Satchwell MN650 Series Bedienungsanleitung

Satchwell

Data Sheets

DS 10.154 - MN650 Controllers

DS 10.202 - VisiSat Configuration Tool

Multi-Lingual Instructions

MLI 10.154 - Installation Instructions

MLI 10.310 - MN DK Installation Instructions

WIRING AND COMMISSIONING INFORMATION FOR

SATCHWELL MICRONET MN650

CONTROLLERS

APPLICATION

Satchwell MicroNet MN650 Series Controllers are fully-programmable

controllers designed for roof top, unit ventilator, air handling unit (AHU)

and zone heating and cooling applications. These controllers feature

universalinputs (UIs),digital inputs(DIs),triac outputsfor24Vac loads,

analogue outputs (AOs) and support for one MN-Sx digital sensor. The

MN650 controller operates from an external 24Vac or 24Vdc supply.

By setting the controller’s jumper pins, any of the universal inputs may

be configured as an analogue, resistive, or dry (volt free) contact input.

MN650 controllers can operate standalone or be networked in a

MicroNet ARCNET®network or a Native Communications Protocol

(NCP) network. For any model of controller, a PC with VisiSat™

Configuration Tool software is necessary to download and modify

applications.

An optional Real-Time Clock card can be fitted, which maintains

controller time during a power failure. The RTC card contains a 3V,

125mAh Lithium cell which has a life of at least 5 years.

Networked controllers receive time updates automatically from a

MicroNet Manager Interface or Touch Screen time master.

A Satchwell MicroNet Touch Screen or LCD can be mounted onto the

controller, which allows a user to view and modify controller properties.

Please refer to the Touch Screen Engineering Data Sheet (DS

10.050A) or to the LCD Engineering Data Sheet (DS 10.060A).

The controller also features an onboard power capacitor, to preserve

RAM for a maximum of seven days.

SPECIFICATION

Order Type Description Communications Voltage Inputs/Outputs

MN650-ARC MicroNet 650 ARCNET

Controller ARCNET 24Vac

50/60Hz

24Vdc

12 Universal inputs configurable for temperature, digital

input or voltage (0 to 10Vdc) input.

4AOs providing 0 to10Vdc at 1mA. Load resistancemust

be 10kΩor more.

8 DIs - Volt Free Contact (VFC) or wet contact (24Vac or

24Vdc).

8 Triac outputs for 24Vac.

15Vdc (25mA) supply output for humidity and pressure

sensors, etc.

1 S-Link sensor.

MN650-NCP MicroNet 650 NCP Controller NCP

MN650-XCOM MicroNet 650 Dual NCP

Controller Dual NCP

MN650

INSTALLATION

Inspection

Inspect carton for damage. If damaged, notify carrier immediately.

Inspect controller for damage. Return damaged products.

Requirements

(These items are not provided)

•Installer must be an experienced technician.

•Job wiring diagrams.

•Tools:

– Drill and bits for panel mounting screws.

– Digital Volt-Ωmeter (DVM).

– Static protection wrist strap.

•EN 61558 power transformer as described opposite.Three No. 10

self-starting screws for wall mounting or 35mm DIN rail for mounting.

Precautions

General Cautions

Follow Static precautions when installing this equipment.

Use copper conductors that are suitable for 75°C.

Make all connections according to electrical wiring diagram.

Do not route power and output wiring with signal wiring.

Do not run Extra Low Voltage (24Vac or less) wiring in the same

harness as mains wiring.

All installation wiring must conform to BS 6701:2004 and

EN 50174.

Static Precautions

Static charges damage electronic components. The microprocessor

and associated circuitry are extremely sensitive to static discharge.

Use the following precautions when installing, servicing, or operating

the system:

•Work in a static-free area.

•Discharge static electricity by touching a known, securely grounded

object.

•Use a wrist strap connected to earth ground when handling the

controller’s printed circuit board.

European Community Directives

This equipment meets all requirements of European Community

Directives for Low Voltage (72/23/EEC), General Safety (92/59/EEC),

and Electromagnetic Compatibility (89/336/EEC).

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Canadian Department of Communications (DOC)

This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the radio interference

regulations of the Canadian Department of Communications.

Power Supply Wiring Precautions

•This product contains a non-isolated half-wave rectifier power

supply and must not be powered by transformers used to power

other devices containing non-isolated full-wave rectifier power

supplies. Refer to DS 10.250, EN-206, Guidelines for Powering

Multiple Full-Wave and Half-Wave Rectifier Devices from a

Common Transformer for detailed information.

•The 24Vac 50/60Hz supply must comply with EN 61558 and be

capableof supplyingat least13VA.Class 2circuits mustnot intermix

with Class 1 circuits. The supply to the transformer must have a

breaker or disconnect.

•The transformer frame and controller GND terminal must be

connected to earth; see page 7.

Mounting

Panel or DIN Rail Mounting

1. Select mounting location. Allow minimum 150mm clearance

around controller.

2. Do the following to mount controller on a panel:

a. Loosen two screws securing terminal cover and remove cover.

b. If not already fitted, press the wall mounting clip into the back

of the controller.

c. Lift wall mounting bracket clip. (Located on top back of

controller.)

d. Using a No. 10 self-starting screw, install top screw.

e. Lift and level controller.

f. Using two No. 10 self-starting screws, install bottom screws.

g. Re-install terminal cover. (May be left off until wiring is

completed.)

3. Do the following to mount controller on a DIN rail:

a. While pulling down on DIN rail locking bracket, snap controller

base on a 35mm DIN mounting rail.

b. Release DIN rail locking bracket.

Location

The controllers are suitable for indoor use only. When selecting a

mounting location, make certain the following conditions are met:

•Do not install where excessive moisture, corrosive fumes, vibration,

or explosive vapours are present.

•Do not install near large contactors, electrical machinery, Variable

Speed Drives (VSDs) or welding equipment.

•Allow 150mm clearance from contactors, switches, and associated

cabling.

Locate where ambient temperatures do not exceed 50°C or fall below

0°C and relative humidity does not exceed 95% or fall below 5%,

non-condensing.

MOUNTING METHODS

Panel Mounting DIN Rail Mounting

Terminal Connections

Wiring Routing Rules

The following table shows cable types that can be routed together:

Cable Screens

Earth each screen, but at only one end of the cable network, preferably

at the GND terminal (14) of an MN50-MI-NCP/ARC. If earthing a

screen at an MN650 controller, connect to terminal 40 (GND). Keep

wires emerging from screened cable as short as possible (and not

more than 150mm).

Note:Satisfactory NCP or ARCNET communications relieson the LAN

REF potential varying no more than 12V between any two devices in

the network (e.g. between an MN50-MI-NCP/ARC and any controller,

or between any two controllers). If this is not the case, introduce NCP

repeaters or ARCNET routers and connect the network as given in the

MicroNet System Engineering Guide.

Network Wiring

Introduction

Network wiring includes a connection between the controller and a

MicroNet controller network. Depending on the specific controller

model, one of two network types can be used:

•NCP network

•ARCNET network

Note that termination of cable screens can be critical to performance,

particularly in an ARCNET network. Network wire pairs must be

dedicated to MicroNet network communications. They cannot be part

of an active, bundled telephone trunk. If network cable is installed in

areas of high RFI/EMI, the cable must be in conduit.

Refer to the MicroNet System Engineering Guide for further guidance,

including network topologies, wiring, network lengths, termination,

screening and cable types.

NCP Network Wiring

MN650-NCP VARIANT

Controllers may be networked to either a 'main LAN' under an

MN50-MI-NCP or to a 'sub-LAN' under a MicroNet Touch Screen.

Recommended cable for NCP networks is Belden 9502 dual

twisted-pair screened cable for full opto-isolation in areas of high

electrical noise. However, Belden 8762 (single twisted pair cable) can

be used providing that the wiring precautions shown in the MicroNet

System Engineering Guide are followed.

Theterminals touse fornetwork connections dependon whetheror not

a Touch Screen is mounted on the controller.

1. Review the Precautions section.

2. If applicable, fit or remove two links as shown in the following

diagram:

PT No. 3/08455100_0

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

24V

GND

DO1

DO2

DO3

DO4

DO5

DO6

DO7

DO8

DI1

DI2

DI3

DI4

DI5

DI6

DI7

DI8

57 58 59 60 61 62 63 64 65 66 67 68

UI1

UI2

UI3

UI4

UI5

UI6

UI7

UI8

UI9

UI10

UI11

UI12

UI1 COM

UI2 COM

UI3 COM

UI4 COM

UI5 COM

UI6 COM

UI7 COM

UI8 COM

UI9 COM

UI10 COM

UI11 COM

UI12 COM

18 19 20 21 22 23 24 25 26 27 28 29

69 70 71 72

LAN A

LAN A +

LAN B

LAN B +

LAN A REF

LAN B REF

30 31 32 33

73 74 75 76 77 78

AO1

AO2

AO3

AO4

15Vdc

S-LINK

AO1 COM

AO2 COM

AO3 COM

AO4 COM

0Vdc

S-LINK

34 35 36 37 38 39

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

34 35 36 37 38 39

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

73 74 75 76 77 78

Terminals accept one 1.5mm2wire

Terminals 1 to 17 are internally linked.

CommsaS-Link DI (24V) UI AO DO 24Vac DO 240Vac

Commsa

a Comms must always be screened.

9 9 9 9 9 8 8

S-Link 9 9 8 9 9 8 8

DI (24V) 9 8 9 9b

b Screen UI

9c9 8

UI 9 9 9b9 9 9b8

AO 9 9 9c

c Screen AO

9 9 9c8

DO 24Vac 8 8 9 9b9c9 8

DO 240Vac 8 8 8 8 8 8 9

Screens.

Use a terminal block if you

have more than one screen

to earth at the controller.

40 (GND)

3. Connect the network to the controller, as shown in the following

diagrams. Observing correct polarity, connect one pair of the

dual twisted pair to the LAN and connect both wires of the other

pair to one of the LAN isolated (LAN REF) reference terminal(s).

Note: Connect the controller with other NCP devices in a

device-to-device fashion. Do not use wiring trees or stubs.

4. Ground the NCP wiring screen at one end of the cable only, e.g.

at the earth terminal of an MN50-MI-NCP. Mounting a MicroNet

Touch Screen in the controller causes the controller to be on a

sub-LAN of the Touch Screen. If required, continue the MicroNet

sub-LAN from pins 32, 33 and 71 or 72. The main LAN must connect

to pins 30, 31 and 69 or 70.

MN650-XCOM VARIANT

The MN-XCOM variant allows a local MN50-LCD to be connected to

the LAN B at pins 32 and 33.

ARCNET Network Wiring

Controllers may be networked to either a 'main LAN' under an

MN50-MI-ARC or to a 'sub-LAN' under an ARCNET router

(MN50-MI-RTR).

For performance reasons, when transferring network variables

between controllers and Touch Screens, the main LAN should have

only ARCNET routers connected to it, unless there are no sub-LANs.

Recommended cable for ARCNET networks is Belden 9502 dual

twisted-pair screened cable.

1. Review the Precautions section.

2. Ensure both links from the daughter board header are removed.

3. Connect the network to the controller, as shown in the following

diagrams. Observing correct polarity, connect one pair of the

dual twisted pair to the LAN and connect both wires of the other

pair to one of the LAN isolated (LAN REF) reference terminal(s).

4. Connect the controller with other ARCNET devices in a

device-to-device fashion. Do not use wiring trees or stubs.

5. Ground the ARCNET wiring screen at one end of the cable only,

e.g. at the earth terminal of an MN50-MI-ARC.

Thedevices at each end of the network must be biased and terminated

by fitting jumpers to A, B and C of LK4. If the controller is not at one

end, leave the links unset.

A local MN50-LCD can be connected to the controller at pins 32, 33

and 71 or 72 (LAN B):

123 4 5 6789 101112131415161718192021222324252627282930313233

343536373839

4041424344454647484950515253545556575859 60616263646566676869707172

737475767778

This connector must have two links fitted to the

MN-650-NCP only (not the MN-650-XCOM).

Remove both links if using a Touch Screen.

{

MicroNet

NCP

Network

NCP Wiring when Touch Screen is not mounted on Controller:

Refer to the Cable Screens

section.

69 or 70

2nd twisted pair

connectedtoisolated

(LAN REF) reference

LAN A

(LAN A REF)

{

Main LAN

Sub-LAN

NCPWiringwhen TouchScreen

is mounted on Controller:

Refer to the Cable Screens

section.

69 or 70

71 or 72

2nd twisted pair

connectedtoisolated

(LAN REF) reference

LAN A

LAN B

(LAN B REF)

{

Main LAN

MN50-LCD

NCP Wiring when MN50-LCD is connected to the

Controller (no ribbon cable connected):

Refer to the Cable Screens

section.

69 or 70

2nd twisted pair

connectedtoisolated

(LAN REF) reference

LAN A

LAN B

Ensure both links from

daughter board header

are removed.

(LAN A REF)

MicroNet

ARCNET

Network

{

Refer to the Cable Screens

section.

69 or 70

2nd twisted pair

connectedtoisolated

(LAN REF) reference

LAN A

(LAN A REF)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

34 35 36 37 38 39

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

73 74 75 76 77 78

ARCNET termination

and biasing links

LK4

A = Bias-

C = Bias+

B = TM/TERM = Termination

{

Main LAN

MN50-LCD

NCP Wiring when MN50-LCD is connected to the

Controller (no ribbon cable connected):

Refer to the Cable Screens

section.

69 or 70

71 or 72

2nd twisted pair

connectedtoisolated

(LAN REF) reference

LAN A

LAN B

(LAN B REF)

(LAN A REF)

Ensure both links from

daughter board header

are removed.

S-Link Sensor Wiring

1. Review the Precautions section.

2. Connect unscreened cable to terminals 39 and 78. Polarity makes

no difference.

See the MN-Sx data sheet (DS 10.000A) for sensor connection

details.

Universal Input (UI) Wiring

UI Configuration

Each UI must be configured as either a Voltage (0 to 10Vdc),

Resistive/Temperature (0-10kΩ), or Digital Input. This must match the

usage of the UI in the controller application. Configuration is achieved

by placing the shorting block (jumper) onto the appropriate pins:

Refer to the controller’s 'Controller Definition Drawing' in VisiSat for a

picture of the required UI jumper settings for the controller. Factory

default configuration is shown in the following table. If an input is not

used, leave jumper in the default position.

Note: Each device connected to a UI must use a separate signal and

return conductor. If screened cable is used, connect the screen to

ground at one end only.

Voltage UIs

Note: An externally powered 0 to 10Vdc sensor is required. The input

impedance of a voltage input is 430kΩ.

1. Review the Precautions section.

2. Connect positive signal wire from 0 to 10Vdc device to desired

input terminal (18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28 or 29).

3. Connect negative signal wire to one UI common (COM ) terminal

(57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67, 68).

4. Make certain jumper is in Voltage position.

Resistive (Temperature) UIs

1. Review the Precautions section.

2. Connect one wire from the resistive device to desired input

terminal (18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28 or 29). Polarity

is not important.

3. Connect other wire to UI common (COM ) terminal (57, 58, 59, 60,

61, 62, 63, 64, 65, 66, 67, 68).

4. Make certain input configuration jumper is in Resistive position.

Digital UIs

Note: Only dry (voltage free) contacts can be monitored. Maximum

count frequency is once every two seconds.

1. Review the Precautions section.

2. Connect one wire from field contact to desired input terminal (18,

19, 20, 21, 22, 23, 24, 25, 26, 27, 28 or 29). Polarity is not

important.

3. Connect other wire to one UI common (COM) terminal (57, 58, 59,

60, 61, 62, 63, 64, 65, 66, 67, 68).

4. Make certain input configuration jumper is in Digital position.

Wiring for 15Vdc Source

The 15Vdc terminal can provide a 25mA source for use with a DUSF

sensor.Connect load to terminal 38 and 77.

Terminal

Number Input

Number Resistive

ADigital

BVoltage

18 1Link 1A

19 2Link 2A

20 3Link 3A

21 4Link 4A

22 5Link 5A

23 6Link 6A

24 7Link 7B

25 8Link 8B

26 9Link 9B

27 10 Link 10B

28 11 Link 11C

29 12 Link 12C

{

S-Link Sensor 39

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

34 35 36 37 38 39

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

737475 7677 78

B = Digital

C = Voltage

A = Resistive

1 2 3 4 5 6 7 8 9 10 11 12

LK19

LK7

Configure input as Voltage UI

18,19, 20,21,22, 23,24,25, 26,27,28

or 29

57,58, 59,60,61, 62,63,64, 65,66,67

or 68

Refer to the Wiring Routing Rules section.

18,19, 20,21,22, 23,24,25, 26,27,28

or 29

57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67

or 68

Configure input as Resistive UI:

Refer to the Wiring Routing Rules section.

Configure input as Digital UI:

18,19, 20, 21,22,23,24,25, 26, 27,28

or 29

57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 6

or 68

Refer to the Wiring Routing Rules section.

15Vdc load 38

Digital Input (DI) Wiring

The digital inputs may be used as simple equipment status inputs.

1. Review the Precautions section.

2. Connect one wire from field contact to desired input terminal (49,

50, 51, 52, 53, 54, 55 or 56). Polarity is not important.

Triac Wiring

The selected wire gauge must be consistent with load current rating.

Review the Precautions section before wiring.

Triac loads can be powered from either the controller’s 24Vac supply

or from an external 24Vac supply. Where the controller is powered

from a 24Vdc supply, the triac load must be powered from an external

24Vac transformer.

Internally Powered Triac Loads

A suitably rated transformer must be used, with the 24Vac wired to

terminal 1 and the Common wired to terminal 40 (GND). Terminals 1 to

9 are internally linked.

Externally Powered Triac Loads

Each load should be connected and powered as follows:

To wire a floating control 24Vac actuator:

1. Review the Precautions section.

2. Connect 24Vac supply to actuator common terminal.

Connect drive open and drive close actuator terminals to appropriate

triac output terminals.

Analogue Output (AO) Wiring

AO1 to AO4 supply from 0 to 10Vdc to modulate a voltage controlled

device.

•Minimum input impedance for a device or actuator operated by an

AO is 10kΩ.

•The maximum current that a 0-10Vdc output can source is 1mA.

3. Review the Precautions section.Connect positive signal wire to

desired output terminal (34, 35, 36 or 37).

Connect negative signal wire to the corresponding AO COM terminal

73, 74, 75 or 76).

Power Supply Wiring

Notes:

1. If using a touch screen via the ribbon cable, the MN650 must be

supplied from 24Vac, not 24Vdc.

2. This product contains a non-isolated half-wave rectifier power

supply and must not be powered by transformers used to power

other devices containing non-isolated full-wave rectifier power

supplies. If multiple devices are powered from the same

transformer, verify that the transformer is properly sized to power

all equipment simultaneously and all devices contain the same

type of rectifier power supplies or internal isolation. Also verify that

correct polarity has been maintained between all connected

devices. Refer to DS 10.250, EN-206, Guidelines for Powering

Multiple Full-Wave and Half-Wave Rectifier Devices from a

Common Transformer for detailed information.

3. Install wiring according to job wiring diagrams and local electrical

codes.

The wire gauge used must be consistent with load current rating.

24Vac Power Wiring

1. Review the Precautions section.

2. Ensure that the controller GND terminal is connected to Earth

before connecting the power wiring to the controller.

3. Connect power ground wiring to terminal 40 (GND).

4. Connect power 24Vac wiring to terminal 1 (24V~).

24Vdc Power Wiring

1. Review the Precautions section.

2. Ensure that the controller GND terminal is connected to Earth

before connecting the power wiring to the controller.

3. Connect power ground wiring to terminal 40 (GND).

4. Connect power 24Vdc to terminal 1 (24V~).

DI Wiring: Dry Contact (VFC)

Refer to the Wiring Rules section.

49, 50, 51, 52, 53, 54, 55 or 56

10, 11, 12, 13, 14, 15, 16, 17

Terminals 10 to 17 are

internally linked.

DI Wiring: Wet Contact:

Not Connected

49, 50, 51, 52, 53, 54, 55 or 56

10, 11, 12, 13, 14, 15, 16, 17

24Vac or 24Vdc Common 40 (GND)

Note: The source 0V must reference GND (Terminal 40)

Source (24Vac or 24Vdc)

24Vac Common

2, 3, 4, 5, 6, 7, 8, 9

41, 42, 43, 44, 45, 46,

47, 48

Load 18VA max.

24Vac

24Vac230Vac 1 (24~)

40 (GND)

External

transformer

24Vac

40 (GND)

41, 42, 43, 44, 45, 46,

47, 48

24Vac Common

Triacs can switch 18VA max.

Load

Analogue Output

0 to 10Vdc 34, 35, 36 or 37

73, 74, 75 or 76

Refer to the Wiring Routing Rules section.

Primary

Ground Frame of

Transformer to

Known Ground

24Vac Secondary EN 61558.

13VA at 50/60Hz.

1(24V~)

40 (GND)

{

1(24V~)

40 (GND)

24Vdc

Supply

CHECKOUT

Electrical Checkout

1. If controller is part of a MicroNet NCP or ARCNET network, verify

network wiring between controller and other devices is installed

according to job wiring diagram and national and local electrical

codes.

2. If operated from a 24V supply, verify that 24Vac power is provided

from a power transformer conforming to EN 61558 and wiring is

installed according to job wiring diagrams and with national and

local electrical codes.

3. Verify input jumpers are in correct position.

4. Verify outputs are wired according to job wiring diagram and with

national and local electrical codes.

5. Make certain current requirements of the controlled device do not

exceed rating of controller’s digital outputs.

Setting the Address of an NCP/ARCNET Controller

Each controller or other device on the same NCP or ARCNET LAN

needsa uniquenode address. The nodeaddress oftwocontrollerscan

bethe same if they are on different LANs; that is, separated bya Touch

Screen (NCP networks) or router (ARCNET networks).

Set the node address using switches 1 to 7 in bit switch S1. Do this

before powering up and cold starting the controller.

NCP/ARCNET CONTROLLER ADDRESS

Example: Placing switches 1, 3 and 6 in the ON position and switches

2, 4, 5 and 7 in the OFF position sets controller address to 37:

Although the controller’s address is set using the switches, the

controller’s address is activated only after the controller is cold or warm

started, as described on page 8. If the address has not been activated,

you will not be able to connect to the controller from VisiSat.

Cold and Warm Starting the Controller

Cold Start

Caution: If the controller’s Configuration Locked property has not

been set to Yes in VisiSat, the cold start procedure clears all

configuration data from the non-volatile EEPROM of the

controller. This means the control application will be erased.

A cold start is normally performed only once when controller is first

installed and before the controller application is downloaded. A cold

start results in all controller outputs OFF until an application is

downloaded. The cold start is performed using the controller’s switch

S1.

To perform a cold start:

1. Verify all devices connected to controller are in a manually

controlled safe state.

2. Energize controller and verify the following:

•Green ’Heartbeat’ LED (LD5) is steady on for a short period.

•After steady on period, the green LED adopts a normal

'heartbeat' flash rate.

3. Place bit switch 8 in ON position and then return to OFF position.

(green LED will flash rapidly for several seconds and then return to

normal 'heartbeat' rate.)

Notes:

1. Refer to ’Diagnostics LEDs’ section if required.

2. An online controller can also be cold started from VisiSat using

Force Defaults in the controller’s System object in Bubbleland.

Warm Start

A warm start resets the controller and causes any change of address

to be activated. When the controller is warm started, all

EEPROM-resident values are retained. However, controller outputs

cannot be guaranteed to stay at their present state.

To perform a warm start:

1. Verify all devices connected to controller are in a manually

controlled safe state.

2. Do one of the following:

•Select the Force Reset option from the controller’s System

object in Bubbleland (the controller must be online).

•Cold start the controller with the controller’s Configuration

Locked property set to Yes.

•Switch the power to the device Off, then On again.

Diagnostic LEDs

Switch Number OFF Position ON Position

1 0 1

2 0 2

3 0 4

4 0 8

5 0 16

6 0 32

7 0 64

Switch Number OFF Position ON Position

1ON 1

2OFF 0

3ON 4

4OFF 0

5OFF 0

6ON 32

7OFF 0

TOTAL Node Address = 37

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

34 35 36 37 38 39

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

73 74 75 76 77 78

Bit Switch S1 Location

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 2930 31 32 33

343536373839

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 6869 70 71 72

737475767778

Location of LEDs (if fitted)

LD1 (Green)

LD2 (Red)

ARCNET/UART

Status

NCP Activity

Controller

Status

LD5 (Green)

LD3 (Red)

LD8 (Yellow)

LD7 (Yellow)

ARCNET/UART

Status

LD6 (Yellow)

LD4 (Yellow)

CONTROLLER STATUS LEDs

The Controller Status LEDs LD3 and LD5 have the following meanings:

NCP LEDs

LEDs LD7 and LD8 have the following meanings:

ARCNET LEDs

LEDs LD1 and LD2 have the following meanings:

SERVICING

Components within the controllers cannot be field repaired. If there is

a problem with a controller, carry out the following procedure before

contacting your local sales office.

1. Make sure controllers are connected and communicating to

desired devices.

2. Check all sensors and controlled devices are properly connected

and responding correctly.

3. If controller is operating, make sure the correct application is

loaded by using the VisiSat Configuration Tool. For more

information, see the VisiSat Engineering Guide.

4. Cold start the device and reload its application.

5. Record precise hardware setup, indicating the following:

•Controller firmware version number.

•Information regarding the Version number and build number of

the VisiSat Configuration Tool (see 'About VisiSat' option in the

VisiSat Tool Help menu).

•A complete description of difficulties encountered.

•A description of the status of the diagnostic LEDs.

Fuse Replacement

A fuse provides overcurrent protection for the controller. Observing

static precautions, do the following to check and replace fuse.

1. Turn OFF all power to controller.

2. Remove controller covers.

3. Remove fuse using long nose pliers or similar.

4. Check continuity across fuse.

5. If fuse is faulty, replace fuse with same type and rating (1A

anti-surge).

6. Re-install cover.

LD3 (Red, ’Error’ LED) Indicates that the unit has a problem requiring

attention as follows:

•Long pulse at Flasher object rate (see note)

- Node Error.

•50% pulse at Flasher object rate (see note)

- Null Outputs.

•Short pulse at Flasher object rate (see note)

- Unprogrammed.

•Very fast strobe - Uncalibrated.

Note: The pulse rate is determined by the

Flash rate set up in the System Flasher object

in bubbleland (default 1 flash per second).

LD5 (Green

’Heartbeat’ LED) ARCNET only:

•Pulsing (more on than off) - indicates a

duplicate ARCNET node ID

•Pulsing (more off than on) - indicates that

ARCNET is initialising and seeking other

nodes.

NCP/ARCNET:

•Flashing on and off at Flasher object rate

(see note) - indicates unit is running

correctly.

•Fast strobing - indicates that the unit is

initialising and reading/writing to EEPROM.

LD7 (Yellow 'Rx' LED) Indicates successful reception of NCP

data packets.

LD8 (Yellow 'Tx' LED) Indicates successful transmission of NCP

data packets.

LD1 (Green, 'Online' LED) •Constantly on - indicates that the

ARCNET node ison line and connected

to the network (normal use).

•Flashing on and off - indicates

network connection has been lost and

reconnection is being established.

LD2 (Red, 'Error' LED) •Off - indicates initialisation of the

ARCNET device has failed (will occur if

no ARCNET device is fitted (normal)).

•Long on and off periods - indicates

network connection failure

•Short on and off periods - indicates

recent node network connection or

disconnection (possible network

problem if occurring frequently).

•Constantly on - indicates a bus wiring

fault.

•Flashing - indicates that the node isnot

connected to the network (floating

node)

LD4 (Yellow 'Rx' LED) Indicates successful reception of

ARCNET data packets.

LD6 (Yellow 'Tx' LED) Indicates successful transmission of

ARCNET data packets.

12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1920 21 22 23 24 25 26 27 28 2930 31 32 33

34 35 36 37 38 39

40 41 42 43 4445 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 6667 6869 7071 72

73 74 75 76 77 78

Remove and replace

fuse using long nose

pliers or tweezers

Fuse holder Fuse

Satchwell

All brand names, trademarks and registered trademarks are

the property of their respective owners. Information contained

within this document is subject to change without notice. All

rights reserved.

TAC Headquarters

Malmö, Sweden

+46 40 38 68 50

Satchwell Helpline

+44 (0) 1753 611000

satchwell.info@uk.tac.com

DS 10.154A

www.tac.com

03/06

DIMENSION DRAWING

Weights:

MN650 approx. 1000g

RTC Card approx. 6g

Cautions

•Do not apply any voltages until a qualified technician has checked the

system and the commissioning procedures have been completed.

•This is a 24Vac/dc device. Do not exceed rated voltage. Local wiring

regulations and usual safety precautions apply.

•24Vac must be supplied by a transformer conforming to EN 61558.

•If any equipment covers have to be removed during the installation of

this equipment, ensure that they are refitted after installation to

comply with UL and CE safety requirements.

•Do not exceed the maximum ambient temperature.

•Interference with parts under sealed covers invalidates guarantee.

•Do not charge, short-circuit or solder the MN RTC battery. Do not

allow contact with water, nor heat, disassemble or dispose of in fire.

Do not reverse polarity in application.

•The design and performance of TAC Satchwell equipment is subject

to improvement and therefore liable to alteration without notice.

•Information is given for guidance only and TAC Satchwell does not

accept responsibility for the selection or installation of its products

unless information is given by the Company in writing relating to a

specific application.

•All installation wiring must conform to BS 6701:2004 and EN 50174.

•A periodic system and tuning check of the control system is

recommended. Please contact your local sales office for details.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Satchwell Temperaturregler Handbücher

Satchwell

Satchwell DRT Series Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema