Satel CA-64 PP Bedienungsanleitung

- 1 -

ZONES & OUTPUTS EXPANDER

WITH POWER SUPPLY

CA-64 PP

SUBPANEL

ca64pp_e 06/04

The CA-64 PP expander (referred to as the subpanel) is a device designed to

interface with the CA-64 alarm control panel. It makes possible extension of the alarm

system by eight zones and eight outputs (4 relay outputs and 4 OC type outputs).

Features of the zones and functional characteristics of the outputs are identical as

those of the main board of the alarm control panel.

NO and NC type detectors can be connected to the expander inputs. The zones can

be configured to work with a single parameter (EOL - the circuit closed with a 2.2kΩ

resistor) and with a double parameter (2EOL - the circuit closed with two 1.1kΩ

resistors). Each of the zones can be individually programmed and assigned one of

a few dozen types of response to violation. Furthermore, every zone can be

individually programmed with possible selection of one of a few dozen types of output

signals.

The module is fitted with a built-in impulse power supply unit of 2.2A capacity. It also

has a short-circuit protection of the supply output as well as battery charging and

testing circuits with disconnection of discharged battery.

MODULE DESCRIPTION

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

TMP COM CLK DAT+12V+12V COM AC AC

Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 C1 NC1 NO1 C2 NC2 NO2 C3 NC3 NO3 C4 NC4 NO4

EXPANDER HOUSING

ANTI-TAMPERING CONTACT

D9 D10

T3.15A

5W0.1ΩJ

350mA

700mA

J28

(RED) (BLACK)

BATTERY

1 2 3 4 5 6 7 8

RESET

CA-64 PP

+12V

OUT8

OUT7

OUT6

OUT5

J12

- 2 -

EXPANDER TERMINALS:

Z1 to Z8 - zone line CLK, DAT - expander bus

C1 to C4 - relay terminal, common +12V - power supply output

NC1 to NC4 - relay terminal COM - ground

NO1 to NO4 - relay terminal AC - module supply 17...24V AC

TMP - input of expander anti-tampering circuit (NC)

J12 - jack - outputs OUT5 to OUT8

The AC terminals serve to connect the secondary winding wires of the mains

transformer. The alternating supply voltage can be 17...24V high. The minimum value

of input voltage with the transformer loaded to the maximum by the module is 16V

(AC).

The set of switches situated on the board is intended for setting up the individual

expander address.

Ten light-emitting diodes (LED) are provided on the board:

OUT1- Eight LEDs situated close to the relays indicate the status of individual

-OUT8 expander outputs.

D9 The LED situated next to the addressing switches indicates the process of

communication between the control panel and the expander. During normal

work of the module the LED blinks with changing frequency.

D10 The LED situated close to the pins designated as J28 is on when the module

is testing the battery status as well as when discharged battery is being

charged.

During testing, the processor reduces the power supply voltage, and the

consumers are supplied from the battery. The testing takes place every

4 minutes and lasts less than 20 seconds.

The J28 pins are used to set up the battery charging current:

350mA- pins shorted,

700mA- pins open.

Two leads (red and black) are used to connect the battery.

The RESET pins are used in production process and should not be shorted.

The TMP input is intended for connecting the expander housing anti-tampering

contact, and, if not used, it should be shorted to ground.

The AC terminals are used to connect the secondary winding wires of the mains

transformer. The alternating supply voltage can have a value of 17...24V.

Also other electric energy consumers (e.g. detectors, modules with no power supply,

alarms) may be connected to the expander power supply unit. However, be careful not

to cause an overload. It is advisable to prepare the power supply load balance. The

total of current inputs for all consumers and battery charging current is not to exceed

the capacity of power supply unit.

- 3 -

OUTPUT TYPES

The expander has two types of outputs. The outputs 1-4 are relay outputs while those

numbered 5-8 are OC type outputs.

RELAY OUTPUT

The output controls the status of the relay situated on the expander board. With this

type of output the Cn, NCn and NOn terminals are galvanically isolated from electrical

circuits of the expander. When the output status LED is on, the Cn terminal is shorted

to the NCn terminal, whereas the NOn terminal is isolated. Consequently, when the

LED is off, the Cn terminal is shorted to the NOn terminal, and the NCn terminal is

isolated.

The output structure is shown in the diagram below. Position of the contacts of the

relay presented in the figure refers to the condition

when the LED is off.

P - relay winding

Dn - light-emitting diode LED

n - expander output number

OC TYPE OUTPUT (collector open)

The output intended for connecting the voltage controlled equipment (e.g.: radio

messaging, signaling devices with own power supply). Direct connection to a load

output (e.g. a relay) is possible provided such a load will not enforce a current flow in

excess of 50mA through the output transistor. When the LED indicating the output

status is on, the Cn output terminal is shorted to ground, and when the LED is off, the

Cn terminal is isolated. The output structure and the ways of connecting a load

are presented in the diagram

on the right.

R - load resistance

Dn - light-emitting diode LED

n - expander output number

(

+13,6V

)

AUX

Output n Cn

10Ω

COM

+Ucc

Output n

+13,6V

NCn

NOn

- 4 -

INSTALLATION

The CA-64 PP (zones and outputs) expander with power supply may be installed in

a CA-64 OBU-EXB housing (with 50W transformer and place for 17Ah battery), which

makes it possible to install any expander with power supply as well as an additional

zones expander without power supply. Begin installation of the housing with

placement of distance pins inside.

EXPANDER CONNECTION AND POWER SUPPLY ACTIVATION

The expander power supply unit should work being permanently connected to 230V

AC mains supply. Therefore, before you commence on the cabling work, make

yourself familiar with the electrical system of the site. Choose a circuit that is always

live to power the module. The circuit should be protected with a suitable fuse.

CAUTION ! Before connecting the power supply unit to the circuit, from which it is to be

supplied, switch off voltage in that circuit.

Prior to the commencement of connecting the module to the existing alarm system,

turn off power supply of the whole system.

The first-time expander activation is preferably to be done without battery connected.

The expander power supply is provided with safeguards, which make it possible to

avoid damages to alarm system components resulting from installation faults.

1. Secure the expander board on the distance pins installed in the housing.

2. Connect the bus leads (the first bus: CK1, DT1, COM; the second bus: CK2, DT2,

COM - as designated on the control panel main board) to the terminals CLK, DAT

and COM. Up to 32 modules of various types can be connected to one bus. There

can be 6 outputs expanders installed in the system (the total - and maximum -

number of outputs is 64) and 6 zones expanders, unless the LCD keypad zones

are used the total - and maximum - number of zones is 64). For details concerning

the cable connections, see the CA-64 alarm control panel manual ”System

Description and Installation”.

3. Using the switches set up the expander address.

The address is to be set up by means of the switches 1 to 5. Status of the other

switches (6, 7, 8) is irrelevant. To determine the expander address, summarize the

numbers corresponding to the switches set in position ON, according to the table:

Switch number 1 2 3 4 5

Numerical equivalent 1 2 4 8 16

- 5 -

Examples of addressing:

address = 4 address =2+8=10 address =1+8+16=25

Five switches allow addresses to be assigned to 32 expanders (Numbers from 0

to 31).

Addresses of expanders connected to one bus may not be repeated, while the

sequence of addressing is optional.

4. Connect the leads of the controlled equipment.

5. Connect the leads of the housing anti-tampering contact to the TMP. Where two

expanders are installed in the housing, the TMP input of one of them is to be

shorted to ground, and the contact leads are to be connected to the TMP input of

the other expander.

6. Connect the consumers power supply leads to terminals +12V and COM on

expander board.

7. Connect the 230V alternating voltage leads to the transformer terminals marked

"AC 230V".

8. Connect the output voltage wires of the transformer winding to the "AC" terminals

on the control panel main board. Do not connect two expanders with power supply

to one transformer.

9. Connect the wire of the electric shock protection circuit to the terminal block

provided next to the transformer and marked with the ground symbol .

CAUTION! As the expander module has no switch enabling disconnection of the

mains supply, it is important that you inform the owner or user of the

equipment, how to disconnect it from the mains (e.g. by showing him the

fuse which protects the expander supply circuit).

10. Using the J28 jumper, set up the battery charging current (350mA or 700mA).

11. Switch on the expander 230VAC power supply. Measure the voltage on battery

cables, making sure it has the correct value of approx. 13.7V, and check that all

consumers are properly powered.

12. Switch off the module power supply and connect the battery. The module will not

become active on connecting the battery alone. The processor enables the

module power supply to be switched over to battery operation after about 12

seconds of steady-state voltage at the AC terminals (as from 230V AC mains

switching-on).

NOTE: If the battery voltage drops below 11V, the module will signal battery

malfunction to the control panel, and when the voltage drops to abt. 9.5V,

the battery will be disconnected.

When all the connections are completed and checked for correctness, you can

proceed to activating the expander zones and outputs.

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

- 6 -

MODULE ACTIVATION

NOTE: In systems having expansion modules with their own power supply, it is

recommended to start the panel first, and then the other components of the

system.

1. Switch on power supply of the alarm system and the expander (the D10 LED will go

on and flash with steady light).

2. Call the function “Expander identification”(ÁService mode; ÁStructure;

ÁHardware) from the keypad. The D10 LED control should start blinking. After

completion of the identification, all the new zones and outputs are programmed to

the factory defaults, the detector type being set to zero (no detector) and the output

type also set to zero (not used).

3. Using the DLOAD64 program, set the zones and outputs parameters.

4. End the service mode operation, saving data in the FLASH memory.

NOTE: In the process of identification, the control panel is saving in the modules

memory a special (16-bit) number, which serves to check the modules

presence in the system. Replacement of the expander with another (even

one having the same address set up on the switches) without a new

identification will trigger an alarm (module tamper - verification error).

NUMERATION OF ZONES AND OUTPUTS

The identification function automatically sets up numeration of zones and outputs in

the system. The numbers 1-16 belong to the main board zones and outputs. Further

numbers are assigned to the first bus expanders (from the lowest to the highest

expander address), and then to the second bus expanders. Separate numeration is

set for zones and outputs, besides, numbers 49-64 may be assigned to LCD keypads.

This should be borne in mind when installing new expanders in the system. If the

subpanel address is lower than the address of an expander previously installed in the

system, or where a subpanel is added to the first bus, and there is already another

expander connected to the second bus, the identification function - according to the

principle described above - will shift the numeration of zones or outputs between the

expanders. The subpanel will take over the zone / output numbers of the previously

installed expander, which, in turn, will be given the numbers of new zones /outputs

added to the system. If this is the case, the previously assigned expander zones

/outputs can be restored by means of the DLOAD64 program. To do so, call the

function ”Advanced settings” (ÁStructure; ÁHardware).

- 7 -

TECHNICAL DATA

Number of zones ...........................................................................................................8

Number of outputs.........................................................................................................8

Supply voltage........................................................................................... AC 17V...24V

Internal power supply voltage, rated..........................................................13.6V...13.8V

Power supply current efficiency................................................................................2.2A

Battery charging current (switch-over).................................................350mA or 700mA

Current consumption (with no load of OC type outputs or active relays)................34mA

Current consumption by active relay ......................................................................20mA

OC type output current-carrying capacity...............................................................50mA

Maximum voltage switched over by relay..................................................................24V

Maximum current switched over by relay.....................................................................2A

Dimensions................................................................................................. 101x142 mm

Latest EC declaration of conformity and product approval certificates

can be downloaded from our Web site www.satel.pl

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.pl

Inhaltsverzeichnis

Andere Satel Extender Handbücher

Satel

Satel ACX-210 Bedienungsanleitung

Satel

Satel INT-IORS Bedienungsanleitung

Satel

Satel ACX-201 Bedienungsanleitung

Satel

Satel CA-64 DR Bedienungsanleitung

Satel

Satel ACX-201 Bedienungsanleitung

Satel

Satel CA-64 EPS Bedienungsanleitung

Satel

Satel INT-R Bedienungsanleitung

Satel

Satel CA-64 ADR Bedienungsanleitung

Satel

Satel INT-E Bedienungsanleitung

Satel

Satel CA-64 PP Bedienungsanleitung

Satel

Satel INT-IORS Bedienungsanleitung

Satel

Satel ACX-200 Bedienungsanleitung

Satel

Satel INT-PP Bedienungsanleitung

Satel

Satel ACX-220 Bedienungsanleitung

Satel

Satel ACX-200 Bedienungsanleitung

Satel

Satel CA-64 O-OC Bedienungsanleitung

Satel

Satel INT-ADR Bedienungsanleitung

Satel

Satel ACX-210 Bedienungsanleitung

Satel

Satel CA-64 EPS Bedienungsanleitung

Satel

Satel INT-R Bedienungsanleitung

Satel

Satel CA-64 OPS-OC Bedienungsanleitung

Satel

Satel CA-64 SR Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung