Savant VOM-VP02H Bedienungsanleitung

The Video Processing Output Module, VOM-VP02H, is used to overlay

TrueCommand OSD onto the currently playing video stream. Each

card allows for connection of up to two (2) OSD video streams and

two (2) displays.

Box Contents

(1) VOM-VP02H-06

(1) HDMI Locking Cable (3 feet) (CBL-3LHDMI-xx)

(1) Quick Reference Guide (this document)

Speciﬁcations

Environmental

Refer to the SmartMediaPro chassis speciﬁcations.

Dimensions and Weight

Height

1.31 in (3.33 cm) - Faceplate

Width

5.11 in (12.98 cm) - Faceplate

Depth

6.98 in (17.73 cm) - Faceplate and Board

Weight

Shipping Weight: 1 lb (0.45 kg)

Power

Power is supplied through the SmartMediaPro chassis when module is

inserted (Do not hot plug module).

Power is supplied through the SmartMediaPro chassis when module is

inserted (Do not hot plug module).

Compliance

Safety and Emissions

FCC Part 15 | CE Mark | C-Tick

RoHS

Compliant

Minimum Supported Release

Savant OS

da Vinci 5.2.1

Rear Panel

Graphics

Input 1 and 2

19-pin type A HDMI female digital video/audio

input

Connect to HDMI or Thunderbolt (with

adapter) on Pro Host for TrueCommand OSD.

HDMI 1 and 2

19-pin type A HDMI female digital video/audio

input

Connect to display for TrueCommand OSD

overlay.

Module

Removal Slot

Insert the module removal tool (included with

chassis) into this slot and pull outwards to

remove the module.

Retaining

screws

M3 x 6 mm Phillips head ﬂush mount screws,

Pre-installed in chassis.

Used to fasten the module to the chassis.

IMPORTANT! Module Installation Precautions

ELECTRIC DISCONNECT!

Power Oﬀthe controller by setting the power switch on the rear of

the chassis to Oﬀ(O) and remove the power cord before inserting

or removing any module from the SmartMediaPro chassis. Failure

to do so may cause damage to the equipment.

IMPORTANT! Electrostatic Discharge (ESD) Warning:

Observe the following precautions to avoid damage from electrostatic

discharge (ESD) when handling modules.

•Use an approved ESD wrist or ankle-grounding strap. Ensure the

grounding strap makes good skin contact.

•Connect the clip end of the ground strap to a threaded grounding

stud on the chassis.

•When returning a replaced module to Savant, place the module in the

clamshell package in which it was originally shipped in or a static

shielding bag.

NOTE:

The wrist strap only protects the component from ESD voltages on the

body; ESD voltages on clothing can still cause damage.

VOM-VP02H-06 | 009-0410-02 | 150306

45 Perseverance Way, Hyannis, MA 02601

savant.com | 508.683.2500

Video Processing Output Module VOM-VP02H

Quick Reference Guide

For Product Info

Module Installation

Refer to Module installation Precautions above before installing

module.

1. Power Oﬀthe SmartMediaPro Chassis using the power switch

located on the rear of the chassis and disconnect the AC power

cord.

2. Remove the two (2) M3 x 6 mm retaining screws. Set screws

aside as they will be used later in procedure.

3. Align the module board with the two rails located at the bottom

of the opening and gently slide the module all the way until a

slight resistance is felt. This is where the connector on rear of

the PCB gets seated into the chassis connector.

4. Gently press on the module the rest of the way until it seats into

the connector at the rear of the slot and the plate seats against

the chassis.

5. Insert the screws removed in step 2 and tighten.

Module Removal

Refer to Module installation Precautions above before removing

module.

1. Power Oﬀthe SmartMediaPro Chassis using the power switch

located on the rear of the chassis and disconnect the AC power

cord.

2. Remove the two (2) M3 x 6 mm retaining screws. Set screws

aside as they will be used later in procedure.

3. With the notch in the module removal tool (included with

SmartMediaPro chassis) facing downward, insert the tool into

the slot in the module faceplate.

4. Lower the tip of the tool downward to ensure it is hooked

behind the faceplate and with slight outward pressure, pull the

module outward. A slight resistance will be felt as the module is

unseated from the chassis side of the connector.

5. Slide module out until it is completely removed from chassis.

6. If the module is being replaced, refer to the Module Installation

instructions for proper installation procedure.

7. If the module is not being replaced, install a blank plate using

the two (2) M3 x 6 mm screws removed in step 2. This will

ensure that proper airﬂow through the chassis is retained as well

as preventing dust and debris from entering the chassis.

Wiring and Connections

IMPORTANT!!

The SVR-5000S can only have a single display port connected, a second OSD server is required when using an SVR-5000S host.

VOM-VP02H-06 | 009-0410-02 | 150306

45 Perseverance Way, Hyannis, MA 02601

savant.com | 508.683.2500

Dieses Handbuch passt für folgende Modelle

Andere Savant Steuereinheit Handbücher

Savant

Savant CLI-10K4IN-00 Bedienungsanleitung

Savant

Savant SKL-3040-00 Bedienungsanleitung

Savant

Savant SSC-P008 Bedienungsanleitung

Savant

Savant SmartView VOM-SV02 Bedienungsanleitung

Savant

Savant CLI-8000 Series Bedienungsanleitung

Savant

Savant SAV-LMP-0300 Bedienungsanleitung

Savant

Savant ITP-E8000 Series Bedienungsanleitung

Savant

Savant Smart Host Rack Mountable Bedienungsanleitung

Savant

Savant Pro Host SVR-5200S-00 Bedienungsanleitung

Savant

Savant Pro Host Bedienungsanleitung

Savant

Savant IP Audio 125 with Savant Music 2.0 Bedienungsanleitung

Savant

Savant Pro Host Bedienungsanleitung

Savant

Savant GPM-CP2R20120-21 Bedienungsanleitung

Savant

Savant SKL-3040-00 Bedienungsanleitung

Savant

Savant SKL-3040-00 Bedienungsanleitung

Savant

Savant CLI-PTAC1K1 Bedienungsanleitung

Savant

Savant CLI-1WIRE2 Bedienungsanleitung

Savant

Savant VOM-VP01F Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung