Savant SmartControl 2 Kurzanleitung

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

Savant® SmartControl 2 Wireless Controller

SSC-W002G-01

Deployment Guide

Document Number:

009-1519-00

Document Date:

January 2018

Document Supports:

da Vinci 8.5 and higher

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

Contents

To access the link to the topics in this document, click the topic page.

Important Safety Information - Read First ..............................................................................................................................3!

Safety Statements .............................................................................................................................................................................3!

1.!Introduction...................................................................................................................................................................................4!

2.!Deployment Checklist ...............................................................................................................................................................4!

3.!Box Contents and Specifications..........................................................................................................................................4!

4.!Front and Rear Panel Descriptions ......................................................................................................................................5!

5.!Mounting.........................................................................................................................................................................................6!

6.!Connections and Wiring...........................................................................................................................................................7!

7.!Provisioning Controller to the Local Network .................................................................................................................9!

8.!Blueprint Configuration .......................................................................................................................................................... 12!

9.!Additional Information............................................................................................................................................................ 14!

Appendix A: Network Requirements ....................................................................................................................................... 15!

Appendix B: Provision Controller Using Embedded Web UI.......................................................................................... 16!

Appendix C: System Monitor ...................................................................................................................................................... 18!

Important Notice.............................................................................................................................................................................. 19!

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

Important Safety Information - Read First

Before installing, configuring, and operating Savant equipment and other

vendor equipment, Savant recommends that each dealer, installer, etc. access

and read all the required technical documentation. Savant technical

documentation can be located by visiting Savant.com. Vendor documentation

is supplied with the equipment.

Read and understand all safety instructions, cautions, and warnings in this

document and the labels on the equipment.

Safety Classifications In this Document

Note:

Provides special information for installing, configuring,

and operating the equipment.

IMPORTANT!

Provides special information that is critical to

installing, configuring, and operating the equipment.

CAUTION!

Provides special information for avoiding situations

that may cause damage to equipment.

WARNING!

Provides special information for avoiding situations

that may cause physical danger to the installer, end

user, etc.

Electric Shock Prevention

ELECTRIC

SHOCK!

The source power poses an electric shock hazard that

has the potential to cause serious injury to installers

and end users.

ELECTRICAL

DISCONNECT:

The source power outlet and power supply input

power sockets should be easily accessible to

disconnect power in the event of an electrical hazard

or malfunction.

Weight Injury Prevention

WEIGHT

INJURY!

Installing some of the Savant equipment requires two

installers to ensure safe handling during installation.

Failure to use two installers may result in injury.

Safety Statements

Follow all the safety instructions listed below and apply where relevant.

Additional safety information will be included where appropriate.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong is provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip

over.

13. Unplug this apparatus during lightning storms or when unused for long

periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power supply

cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

15. To completely disconnect this equipment from the AC mains, disconnect

the power supply cord plug from the AC receptacle.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

1. Introduction

This Deployment Guide will aid the installer through the process of installing, configuring, and adding a SmartControl 2 (SSC-W002G-01) wireless controller to a

Savant Pro System. Read through this document in its entirety before beginning the installation process. To begin, ensure that the following items are available:

SmartControl 2 Smart Wireless Controller (SSC-W002G) ...................................................................................................................................................

iOS Device with SmartConnect installed......................................................................................................................................................................................

HELPFUL!The SmartConnect application runs on most iOS devices (iPad, iPhone, iPod Touch) and simplifies the

provisioning process. If an iOS device is not available, the SmartControl 2 controller can be provisioned using the

embedded Web UI. See Appendix B: Provision Controller Using Embedded Web UI for more information on this.

Unique ID (UID) of the SSC-W002G ..............................................................................................................................................................................................

Unique ID is available on sticker on bottom of controller.

Savant Development Environment (SDE/MacBook®) .............................................................................................................................................................

RacePoint Blueprint da Vinci 8.5 or higher.

Network meeting Savant requirements........................................................................................................................................................................................

See Appendix A: Network Requirements

SSID and Passphrase for Wi-Fi Router or Switch to the local network ...........................................................................................................................

2. Deployment Checklist

The checklist can be used to record which steps have been completed.

1. Review Front and Rear Panel Descriptions ........................................................................................................................................................................

See Front and Rear Panel Descriptions

2. Mounting and Wiring ...................................................................................................................................................................................................................

See Mounting

See Connections and Wiring

3. Provision Controller to the Network......................................................................................................................................................................................

See Provision to Local Network

4. Add SCC-W002G to an existing RacePoint Blueprint Configuration ......................................................................................................................

See Blueprint Configuration

See Save Configuration, Generate Services, and Upload Configuration

3. Box Contents and Specifications

For Box Contents and Specifications, refer to the Quick Reference Guide to the SmartControl 2 Wi-Fi Controller (009-1505-xx) located on the Savant Customer

Community.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

4. Front and Rear Panel Descriptions

It is important to read and understand the information in this section before beginning the installation process. Understanding the various states of the Status

LED as well as the requirements of each port are an important part of the installation process.

Reset

Press and hold for five seconds while powered; then release. The Status LED will begin blinking rapidly when reset is complete.

After the reset, the controller will be in Provisioning Mode. See Rapid Blink below.

Off

No power applied. Power supply may not be plugged in.

Solid Green

The controller is provisioned to the local network and communicating with the Savant Pro

System Host. This is normal operation mode.

Blinks Once

Is in Provisioning Mode and ready to be added to the local network.

Blinks Twice

Establishing a connection with the local Savant Pro System Host.

Blinks Three Times

Provisioned to the local network and trying to connect to the Savant Pro System Host.

Short Off Blink

Firmware is updating.

Rapid Blink

The reset button on the front panel was held down for at least five seconds and the

controller is performing a factory reset. After the reset, all network settings are cleared

and the factory defaults are restored.

GPIO (Input)

When configured as an input, the processor looks for either a low (<0.8V DC) or high (>2.4V DC).

Minimum 0V DC / Maximum 12V DC.

GPIO (Output)

When configured as an output, the port provides a binary output of 0-12V DC 150ma max.

Relay

Dry contacts to control devices requiring basic on/off operation (normally open/normally closed). Max: 30V DC 1A.

Input Power

5V DC 1.2A – Use the included power supply.

Cable Lance

Use with included cable tie to secure power supply connection.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

5. Mounting

Mount the controller in a place that is dry, well ventilated, and out of direct sunlight.

5.1. Mounting Plate Installation

The mounting plate included in the shipping box can mount the controller to a wall or existing structure. Follow instructions below to mount the

controller.

1. Place the mounting plate onto a wall so the tabs that hold the controller are oriented horizontally.

2. Mark on the wall the two mounting holes. Install wall anchors and screw the mounting plate to the wall.

3. Snap the controller into the bracket so the tabs on the bracket seat into the slots on the side of the controller.

5.2. Rack or Cabinet Installation

When mounting in a rack or cabinet, the controller should be set on a solid, flat, level surface.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

6. Connections and Wiring

The GPIO and relay connections are made using a 6-pin screw down plug-in connector supplied with the controller and power is supplied using the included

power supply. Use the information below when making control and power connections.

6.1. GPIO and Relay

General Purpose Inputs/Outputs (GPIO) are binary I/O ports used on Savant controllers to trigger an action within the system. Events can be to control a

device such as turning on an amplifier (output) or detecting a state change for a device (input) to perform a workflow. The left 3 pins of the supplied

connector are used for the GPIO connections.

Relays are used when a contact closure (normally open/normally closed) is needed to activate a device such as raising or lowering shades, opening or

closing a gate, or sending control signals to an HVAC system are a few examples. The right 3 pins of the supplied connector are used for the relay

connections.

To connect wires into terminal block connector:

1. Remove power if power is applied.

2. Pull to remove the connector from the rear of the controller.

3. With a small flat bladed screwdriver, turn the screws on the top of connector

counterclockwise until the silver crimps in the front open enough to slide the wire into the

square slot.

4. Strip the ends of each wire to ¼inch. Using the diagram to the left, insert the stripped

wires into the proper slots.

5. Turn the screws clockwise until the screw tightens around each wire. Tug on each wire a

bit to ensure they are installed securely. There should be no bare wires protruding from

the rear of the connector.

6. Plug connector back into the rear of the controller.

6.2. GPIO Pull Down Resistor (PD) Usage

GPIO pins are configured as inputs and are pulled high to 12V while the Host is booting up. To make the GPIO signal low during a Host reboot or a power

cycle, attach the GPIO 1 pin to the PD pin. The PD pin is a 1K ohm pull down resistor (to signal earth ground) which keeps the GPIO output below 0.8V

during the processor boot times.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

6.3. Power and Network Connections

Connect the provided power supply between the 5V DC connection on the rear of the controller and a surge protected 120 – 240V AC 50/60Hz outlet

receptacle. The SSC-W002G-01 communicates with the network over the local Wi-Fi network so a wired connection between the controller and the

network is not required.

HELPFUL! No Ethernet connection is needed. The

controller communicates with the Savant Pro

System Host over the local Wi-Fi network.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

7. Provisioning Controller to the Local Network

The controller communicates with the Savant Pro System Host over the local Wi-Fi network. Read through sections 7.1 – 7.3 to understand the process and

guidelines. Follow sections 7.4 and 7.5 to perform the provisioning process.

7.1. Network Diagram (Provisioning Process)

The diagram below demonstrates the provisioning process. Review the diagram for an understanding on how the process works.

1. During the provisioning process, the SmartConnect application communicates

with the controller using Bluetooth signaling.

2. Once the controller is provisioned, it can communicate using the local Wi-Fi

network.

HELPFUL!

- Savant recommends using DHCP reservation. Refer to the owner’s manual for the local router for information on setting DHCP reservations.

- 802.11r (fast roaming) is not supported. If using a router that supports fast roaming, it should be disabled.

7.2. Checklist for Provisioning

The following items are required to provision the controller using the SmartConnect application.

SSC-W002G SmartControl 2 wireless controller .........................................................................................................................................................

iOS Device with SmartConnect App (v1.6 or higher) installed ...............................................................................................................................

Network SSID and passphrase for the wireless router or switch in local network .........................................................................................

Unique ID (UID) of the controller (obtained from sticker located on bottom of controller)......................................................................

Optional: rpmEmbScanner ...................................................................................................................................................................................................

(Used to access the IP Address of the controller)

7.3. SSID Guidelines

Savant Wi-Fi products can connect to a wireless network that meet the following SSID guidelines.

Maximum SSID Length

32 characters

Maximum Passphrase Length

WPA/WPA2:

8-50 characters

WEP:

10-26

Wireless Standard

802.11 a/b/g/n (2.4 or 5 GHz)

Supported SSID and Passphrase special characters.

SmartControl 2 Wireless Controller Deployment Guide

009-1519-00 | 170103

7.4. Install SmartConnect

To connect the controller to the network, the Savant SmartConnect application must be installed and running on an iOS device such as an iPhone® or

iPad®. The SmartConnect Application can be downloaded from the Apple App Store to your iPhone or iPad.

- From the Apple App Store search for Savant Systems LLC.

- Locate the SmartConnect App and download/install onto your iOS device.

For more information, refer to the SmartConnect Reference Guide (009-1046-xx) located on the Savant Customer Community.

HELPFUL INFORMATION!

- SmartConnect v1.6 or higher is required to provision the SSC-W002G-01.

- The iOS device that the SmartConnect application is running on does not need to be connected to the same network the controller is being

added to.

- The SmartConnect is only supported on the iOS platform. Refer to Appendix B: Provision Controller Using Embedded WebUI for instructions

on how to connect the controller to the local network if the SmartConnect application is not available.

- During the provisioning process, the SSC-W002G must be within 30 feet of the device running the SmartConnect app.

- The iOS device must be running Bluetooth v4.0 or higher.

7.5. Provision Instructions

1. If not already powered, plug the provided power supply and cable between the

controller and a surge protected 100 – 240V AC receptacle. Refer to the Power and

Network Connections section above.

2. By default, a new SSC-W002G-01 controller is set at the factory, to be in provisioning

mode. If the Status LED is flashing the Blinks Once sequence, skip this step. If, however,

the LED is blinking a different sequence, follow the bulleted items below to set the

controller to provisioning mode.

- Press and hold the reset button for five seconds until the Status LED blinks green

rapidly, then release.

- After the reboot (1 – 2 seconds), the Status LED will begin the Blinks Once

sequence. This sequence indicates it is in provisioning mode and ready to be added

to the local network.

3. On the iOS device (iPhone, iPad, etc.), tap the SmartConnect (Connect) icon .

4. Locate the SSC-W002g in the Devices on Bluetooth section. Record the Savant ID

(UID) displayed. This UID will be used later in this procedure.

5. Tap the SSC-W002G entry from the Devices on Bluetooth section of the App.

Andere Handbücher für SmartControl 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Savant Controller Handbücher

Savant

Savant SmartControl RS232 Bedienungsanleitung

Savant

Savant SmartControl 25 Bedienungsanleitung

Savant

Savant Director HST-DIRECTOR Bedienungsanleitung

Savant

Savant SSC-W485 Bedienungsanleitung

Savant

Savant SmartControl SSC-W02R Bedienungsanleitung

Savant

Savant Super Pro Host v2 SVR-7100S Kurzanleitung

Savant

Savant FRC-P100-00 Bedienungsanleitung

Savant

Savant QO PBC-1000-10 Kurzanleitung

Savant

Savant SSC-002485 Betriebsanleitung

Savant

Savant S2 Bedienungsanleitung

Savant

Savant SmartControl 7 Bedienungsanleitung

Savant

Savant SSC-0012 Kurzanleitung

Savant

Savant S2 Kurzanleitung

Savant

Savant SmartControl 12 Bedienungsanleitung

Savant

Savant HST-4001 Bedienungsanleitung

Savant

Savant SmartControl 3 Bedienungsanleitung

Savant

Savant SmartControl 12 Kurzanleitung

Savant

Savant SmartLighting SSL-P018 Bedienungsanleitung

Savant

Savant SSC-0008 Bedienungsanleitung

Savant

Savant SmartMediaPro 6 Kurzanleitung

Savant

Savant SmartControl 3 Bedienungsanleitung

Savant

Savant SmartControl 2 Bedienungsanleitung

Savant

Savant Lamp Controller Bedienungsanleitung

Savant

Savant S2 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch