Savant PRO REM-1000 Kurzanleitung

45 Perseverance Way, Hyannis, MA 02601

Savant.com | 508.683.2500

Savant Pro Remote and Base

REM-1000

Deployment Guide

Document Number:

009-1398-01

Document Date:

October 2016

Document Supports:

da Vinci 8.0

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

Contents

To access the link to the topics in this document, click the topic page.

Important Safety Information .............................................................................................3!

1!Introduction..........................................................................................................................4!

2!Deployment Steps .............................................................................................................5!

3!System Overview ...............................................................................................................6!

4!Remote Base Hardware Overview ..............................................................................7!

5!Provisioning to the Network - SmartConnect ........................................................8!

6!RacePoint Blueprint® Configuration............................................................................10!

7!Upload Configuration .......................................................................................................11!

8!Install Savant Pro App and Sync with Pro Remote ..............................................12!

8.1!Download and Install Savant Pro App...........................................................................................12!

8.2!Create Account for Savant Pro 8 App and Sync to Pro Remote........................................13!

8.3!Sign into Savant Pro 8 App to Sync the Pro Remote..............................................................14!

9!Firmware and Software Updates.................................................................................15!

9.1!Pro Remote Base Firmware...............................................................................................................15!

9.2!Pro Remote Software...........................................................................................................................16!

Additional Documentation...................................................................................................17!

Appendix A: Network Requirements ...............................................................................18!

Important Notice......................................................................................................................19!

Regulatory..................................................................................................................................20!

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

Important Safety Information

Before installing, configuring, and operating Savant® equipment and other vendor equipment, Savant recommends

that each dealer, installer, or integrator, access and read all the required technical documentation. Savant technical

documentation can be located by visiting the Savant Customer Community. Vendor documentation is supplied

with the equipment.

Read and understand all safety instructions, cautions, and warnings in this document and the labels on the

equipment.

Safety Classifications in this Document

Note:

Provides special information for installing, configuring, and operating the equipment.

IMPORTANT!

Provides information critical to installing, configuring, and operating the equipment.

CAUTION!

Provides special information on avoiding situations that may cause damage to equipment.

WARNING!

Provides special information on avoiding situations that may cause physical danger to the

installer, end user, etc.

Electric Shock Prevention

ELECTRIC SHOCK! The source power poses an electric shock hazard that has the potential to cause serious

injury to installers and end users.

ELECTRICAL DISCONNECT:The source power outlet and power supply input power sockets should be easily

accessible to disconnect power in the event of an electrical hazard or malfunction.

Weight Injury Prevention

WEIGHT INJURY! Installing some of the Savant equipment requires two installers to ensure safe handling during

installation. Failure to use two installers may result in injury.

Safety Statements

Follow all of the safety instructions listed below and apply where applicable. Additional safety information will be

included where applicable.

1.!Read these instructions.

2.!Keep these instructions

3.!Heed all warnings.

4.!Follow all instructions.

5.!Do not use this apparatus near water.

6.!Clean only with a dry cloth.

7.!Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.!Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

9.!Plug into a surge protected outlet or receptacle.

10.!Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

11.!To completely disconnect this equipment from the AC mains, unplug from the outlet or receptacle.

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

1!Introduction

This Deployment Guide will guide the installer through the process of installing, configuring, and adding a Savant

Pro Remote and Savant Pro Remote Base (REM-1000) to the Savant Control system.

Before You Begin

Read through this document in its entirety and ensure that the following items are available:

Savant Pro Remote (SUR-1000).......................................................................................................................................

Savant Pro Remote Base (SRB-1000)............................................................................................................................

Savant Host™ (Smart or Pro) licensed and running da Vinci 8.0 or higher.....................................................

Savant Development Environment (SDE) MacBook®...............................................................................................

(with RacePoint Blueprint® da Vinci 8.0 or higher installed)

Ethernet network meeting Savant Requirements .....................................................................................................

(See Appendix A: Network Requirements)

SSID and Passphrase for the Wi-Fi® Router or Switch.............................................................................................

SmartConnect Application (v1.5 or higher) with Bluetooth support installed on an iOS device ...........

Unique ID (UID) of the Pro Remote Base......................................................................................................................

(The UID can be discovered using the SmartConnect or rpmEmbScanner Applications)

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

2!Deployment Steps

Follow these steps to successfully deploy the Savant Pro Remote. This page can be used as a checklist to record

which steps have been completed.

!System Diagram, Connections, and Additional Information .....................................................................................

See System Overview

!Review the Pro Remote Base status LED and reset button operation .................................................................

See Remote Base Hardware Overview

!Provision Pro Remote Base onto network using SmartConnect.............................................................................

See Provision to the Network - SmartConnect

!Add Pro Remote and Base to a Blueprint configuration ............................................................................................

See RacePoint Blueprint® Configuration

!Upload the configuration to the host .................................................................................................................................

SeeUpload Configuration

!Install Savant App and Sync with Pro Remote ...............................................................................................................

See Install the Savant Pro App and Sync to Pro Remote

!Updating Software in Pro Remote and Firmware in Pro Remote Base ................................................................

See Firmware and Software Updates

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

3!System Overview

The REM-1000 system includes a Pro Remote, Pro Remote Base, and power supply. To power the system, simply

plug the supplied power supply between the Pro Remote Base and a surge protected AC outlet/receptacle. Refer

to the system diagram below.

Additional Information:

Pro Remote Base

•!Powered by a 100-240V AC (60/50 Hz) to 5V DC power supply (supplied)

•!Charges the Pro Remote.

•!Communicates with the Savant Control system over Wi-Fi® (2.4 GHz, 802.11 b/g/n).

See Appendix A: Network Requirements.

•!Communicates with the Pro Remote using Bluetooth v4.0.

•!Receives firmware updates when a newer version is available in the da Vinci software running on the Host.

Pro Remote

•!Powered by rechargeable batteries.

•!Communicates with the Pro Remote Base over Bluetooth.

•!Communicates with the Savant Control system through the Pro Remote Base.

•!A maximum of two Pro Remote and Base assemblies per user zone up to a total of 16 per system are supported.

•!All commands (button presses) made on the Pro Remote are sent through the Pro Remote Base to the Savant

Control system for processing.

•!Automatic software updates are initiated overnight if the Remote is cradled and no A/V services are active.

•!Software updates can be initiated manually from the About page on the Pro Remote.

•!The Pro Remote and Base are paired at the factory and are not interchangeable with other Pro Remotes and Pro

Remote Bases.

•!Pro Remote and Base must be within 30 feet (9.14 m) of each other to communicate.

IMPORTANT WARNING!!! The hole next to the power button on top of the remote is for the microphone. Do NOT

insert any objects into this hole or damage to the remote could occur.

Box Contents and Specifications

!Refer to the Quick Reference Guide (QRG) for this product located on the Savant Customer Community for

Box Contents and Specifications.

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

4!Remote Base Hardware Overview

The REM-1000 includes a Pro Remote and Pro Remote Base. The Pro Remote communicates with its Base using

Bluetooth and the Pro Remote Base communicates with the Savant Control system using the local Wi-Fi network.

A Status LED, situated on the bottom of the Pro Remote Base, informs a user of the state of the Pro Remote Base.

The LED states are described below.

Pro Remote Base LED States

Off: No Power.

On Solid (Yellow): The Base is booting.

Blinks Once (Yellow): The Base is in Access Point Provisioning Mode and ready to be provisioned to

the local network.

Blinks Once (Green): The Base is provisioned to the local network but not communicating with the

Savant Host.

On Solid (Green): The Base is provisioned to the local network and communicating with the Savant

Host.

Rapid Blink (Red): If the reset button on bottom of Base is held down for at least five seconds, the

LED will begin a rapid blink (red). When button is released, the Base will reboot to its factory default

settings. At this point, the LED blinks yellow once per second indicating is in Access Point Provisioning

Mode.

Rapid Blink (Yellow): The locate feature was activated. From the SmartConnect App, tapping the

Remote Base entry in the Devices in Bluetooth section activates the locate feature. Refer to the

Connect to Wireless Network - SmartConnect section step 4 below for more information.

Blinking Yellow/Green: Firmware is updating on the Base.

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

5!Provisioning to the Network - SmartConnect

The Pro Remote Base needs to be provisioned to the local network to be able to communicate with the Savant

Control system. Configuring the network parameters onto the Pro Remote Base is done with the SmartConnect

Application.

Important Notes on Provisioning!

•!Network must use the 2.4 GHz Wi-Fi band

•!SmartConnect v1.5 or higher.

•!iOS device must support Bluetooth v4.0.

Checklist for Network Configuration

The following items are required to provision the Pro Remote Base to the local network.

Pro Remote Base Powered On......................................................................................................................................

iOS Device with SmartConnect (v1.5 or higher) App installed.........................................................................

SSID and Passphrase for the Wireless router or switch......................................................................................

Unique ID (UID) of the Pro Remote Base.................................................................................................................. 

Savant Development Environment (SDE) MacBook®...........................................................................................

Optional: rpmEmbScanner .............................................................................................................................................

(To obtain IP Address of the Pro Remote Base)

SSID Guidelines

Savant Wi-Fi products can connect to a wireless network that meets the following SSID guidelines.

Maximum SSID Length:

32 characters

Maximum Passphrase Length:

WPA/WPA2: 8-50 characters

WEP: 10-26 characters

Wireless Standard:

802.11 b/g/n 2.4 GHz

Supported SSID and Passphrase Special Characters:

Connect to Wireless Network – SmartConnect

Provisioning using SmartConnect is described below.

1.!Power On the Pro Remote Base by plugging the supplied power supply between the Base and a surge

protected 100V – 240V AC receptacle. Refer to the System Overview section for more information.

2.!By default, a new Remote Base is set at the factory to be in Access Point Provisioning Mode (Status LED

blinking yellow). If it is, skip this step. If not, the bulleted items below describe how to set it into this mode.

See the Remote Base Hardware Overview section

for LED states.

•!Insert a pointed object (preferably non-metallic)

into the reset button pinhole. Press and hold the

Reset Button for five seconds until the LED begins

a rapid blink (red), then release.

•!LED will switch to solid yellow while Base reboots.

•!After the reboot (5-10 seconds), the Status LED

starts blinking yellow once per second indicating it

is in Access Point Provisioning Mode and ready to

be provisioned with the local network settings.

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

3.!On the iOS device (iPad®, iPhone® etc.), open the SmartConnect Application .

4.!Locate the Remote Base in the Devices on Bluetooth section. Copy the Unique ID displayed. The Unique ID

(UID) will be used later in the procedure when the REM-1000 system is added to RacePoint Blueprint®.

TIP! To help learn the UID of a specific Remote Base when there is more than one Remote Base entry in

SmartConnect, tap the Remote Base entry under the Devices on Bluetooth section. The Status LED on the

bottom of the base will blink rapidly (yellow) for 5 to 7 seconds. Locate the Remote Base with the blinking LED

and write down the UID displayed.

5.!Tap the Remote Base entry from the Devices on Bluetooth dialog window.

6.!In the Pick a Network dialog window that opens, tap the Join Other Network… selection (image not shown).

7.!In the Other Network dialog window that opens (shown below), enter the following:

TIP!

Tap the Use Current Network SSID

field to auto populate the Name

field with the SSID of the local

network.

SSID of the local network.

Tap Choose in the Security field. In the dialog window that opens, select the security

configured on the local network.

Tap the password field and enter the password to the local network.

8.!Tap Join when complete.

9.!A Provisioning Success dialog window will open informing the user that the device successfully provisioned to

the network. Tap OK.

With the Pro Remote Base provisioned, the LED on the bottom of the Pro Remote Base will blink green

indicating it is provisioned to the network but not yet communicating with the Savant Control system host.

Refer to the Remote Base Hardware Overview section for LED state information.

Additional Information

•!The Remote Base entry is now displayed in the Devices on Wi-Fi section of SmartConnect.

•!If desired, the IP Address can be discovered using the rpmEmbScanner application available through the Launch

menu of the Savant Application Manager (SAM).

Launch > rpmEmbScanner.

The next step is to configure the REM-1000 system into RacePoint Blueprint.

REM-1000-01 Pro Remote Deployment Guide

009-1398-01 | 161020

6!RacePoint Blueprint® Configuration

To add the REM-1000 Remote to RacePoint Blueprint, do the following:

1.!Open the Savant Application Manager (SAM).

2.!Open an existing configuration into Blueprint.

3.!Select Show Library from the Blueprint toolbar to open the Component Library.

4.!Enter REM1000 into the Search bar.

5.!Drag the Savant REM1000 (Savant Pro Remote)into a User Zone/Room of the Zone Component List panel.

Note: The REM-1000 Pro Remote and Base cannot be added to a Global Zone. Up to two REM-1000 Pro Remote

systems per User Zone are supported.

6.!Enter a name into the window that opens. The name entered should describe the component being added to

the configuration. Select Create.

7.!Drag the Savant REM1000 (Savant Pro Remote) icon into the Layout panel of Blueprint.

8.!Close the Components window.

9.!Open the REM-1000 inspector by double-clicking the REM-1000 icon.

10.!Add the 16 character Savant Unique ID of the Pro Remote Base (image below).

•!In the SmartConnect section above, the Unique ID

was discovered and copied. Use that UID.

•!The UID can also be found on a sticker on the front

of the Remote Base.

•!The Unique ID can also be discovered through the

rpmEmbScanner application as long as the Pro

Remote Base is communicating with the local

network. Open rpmEmbScanner through the

Launch menu in the Savant Application Manager.

SAM > Launch > rpmEmbScanner

11.!Close the Inspector.

12.!Select the Generate Services icon in the Blueprint toolbar. The State icon will change to blue or green

indicating the services for the REM-1000 Pro Remote and base has been created.

13.!Select Update All UI Screens > Sync with Services from the Blueprint toolbar to sync the user interfaces such

as the iPad® to the Services created. The State icon will change to green when complete.

14.!Save the RacePoint Blueprint configuration.

File > Save from menu bar.

Andere Handbücher für PRO REM-1000

Inhaltsverzeichnis

Andere Savant Fernbedienung Handbücher

Savant

Savant REM-2000 Kurzanleitung

Savant

Savant REMOTE Bedienungsanleitung

Savant

Savant REM-0300RF-00 Kurzanleitung

Savant

Savant PRO REM-1000 Bedienungsanleitung

Savant

Savant SHC-2000-05 Bedienungsanleitung

Savant

Savant REM-2000 Bedienungsanleitung

Savant

Savant Pro System Kurzanleitung

Savant

Savant RTR-1000 Series Bedienungsanleitung

Savant

Savant Select SSR-1000 Bedienungsanleitung

Savant

Savant RTR-1000 Series Kurzanleitung

Savant

Savant Single-Room Pro Remote Bedienungsanleitung

Savant

Savant SSR-2000 Bedienungsanleitung

Savant

Savant X2 Bedienungsanleitung

Savant

Savant Pro Remote Multi-Room Bedienungsanleitung

Savant

Savant SHC-S2-00 Bedienungsanleitung

Savant

Savant SUR-0500 Bedienungsanleitung

Savant

Savant WP3-0002-00 Series Bedienungsanleitung

Savant

Savant PRO REM-1000 Bedienungsanleitung

Savant

Savant PRO REM-1000 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung