Sceptre D54 Bedienungsanleitung
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained
for future use.
1. To clean the monitor screen, first, make sure the monitor is in the power off
mode. Second, stand away from the monitor and spray cleaning solution onto
a rag. Without applying excess pressure, clean the screen with the slightly
dampened rag. Do not spray liquid cleaners directly onto the unit.
2. Do not place your monitor near a window. Exposing the monitor to rain, wa-
ter, moisture or sunlight can severely damage it.
3. Do not obstruct the ventilation openings. They are necessary for air circula-
tion and for protecting the device against overheating.
4. Do not lay anything on top of the monitor-to-PC signal cord. Furthermore,
make sure the cord is placed in an area where it will not be stepped on.
5. Do not remove the cover or attempt to service this unit by yourself. You may
void your warranty. Servicing of any nature should be performed only by an
authorized technician.
6. Safe storage of the monitor is in a range of minus 20 to plus 60 degrees Cel-
sius. Storing your monitor outside this range could result in permanent
damage.
7. If any of the following occur, immediately unplug your monitor and call an
authorized technician.
♦=The power monitor-to-PC signal cord is frayed or damaged.
♦=Liquid has been spilled into the monitor, or it has been exposed to rain.
♦=The monitor has been dropped or the case has been damaged.
♦=The device shows obvious signs of a defect.
8. Please turn to your service center for all questions concerning service and
repair to guarantee the devices performance reliability.
— ii —
FEDERAL COMMUNICATIONS COMMISSION
(FCC STATEMENT)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
•=Reorient or relocate the receiving antenna;
•=Increase the separation between the equipment and receiver;
•=Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected;
•=Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturers may
void the user’s authority to operate this equipment.
A shielded-type power cord is required in order to meet the FCC emission
limits and also to prevent interference to nearby radio and television
reception. It is essential that only the supplied power cord be used.
Use only shielded cables to connect I/O devices to this equipment.
Canadian DOC Notice
For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
— iii —
Table of Contents
Chapter 1_________________________________________1
Introduction____________________________________________ 1
Unpacking __________________________________________ 1
Getting Started _________________________________________ 2
Connecting the Monitor and Stand________________________ 2
Choosing a Workstation________________________________ 3
The AC Connection ___________________________________ 4
The Signal Cable Connection____________________________ 4
Monitor Adjustments __________________________________ 5
Chapter 2_________________________________________6
The On-Screen Display (OSD)_____________________________ 8
The Display Controls__________________________________ 6
Adjusting the Brightness and Contrast_____________________ 7
OSD Main Menu _____________________________________ 8
Color Setup ________________________________________ 10
OSD Window Status _________________________________ 12
Reset and Degauss ___________________________________ 13
Self-Test Screen_____________________________________ 14
Summary of OSD Icons _______________________________ 15
Appendix A ______________________________________17
Trouble Shooting_______________________________________ 17
— 1 —
CHAPTER 1
Introduction
Congratulations on your purchase of the new high performance 17" Monitor.
Much consideration has gone into the design of the monitor in order to meet your
requirements for full compatibility and versatility as well as quality.
Using state-of-the-art electronics, the monitor can support a resolution of
1280x1024, and the on-screen display allows you to customize the display settings
to suit your individual needs. User display settings will be automatically saved to
memory. In addition, at the touch of a button the user can, at any time, return to the
factory default display settings.
Other ergonomic features include a non-glare screen, tilt and swivel and just two
multi-function display controls that allow you to make all monitor display adjust-
ments.
Unpacking
Please make sure the following items are in the shipping package and found in
good condition:
•=17" Monitor
•=Tilt and swivel stand
•=Power cord
•=Signal cable (attached to monitor)
•=This manual
If any of the above are missing or appear damaged, please contact your dealer
immediately.
Connecting the Monitor and Stand
— 2 —
Getting Started
This chapter covers setting up the monitor and stand in a suitable workplace, and
connecting the power cord and signal cable.
Connecting the Monitor and Stand
♦=Align the stand’s four tabs with the slots in the bottom of the monitor.
♦=Insert the tabs into the slots.
♦=Slide the stand toward the front of the monitor. You will hear the
spring lock click into place
♦=If you need to remove the stand, push the spring lock and slide the
stand away from the front of the monitor.
Figure 1: Monitor and Stand Connection
Chapter 1
— 3 —
Choosing a Workstation
Keep the following in mind when choosing a work place for the Monitor.
♦=Place the monitor on a stable even surface.
♦=Access to an electrical outlet and telephone jack.
♦=Ensure at least three inches clearance at the rear of the monitor to allow
for sufficient airflow.
♦=Position the Monitor a little above eye-level to reduce neck-strain.
♦=Do not place near a window. Exposing the Monitor to direct sunlight
for extended periods may damage the unit.
♦=You may want to use a desk lamp to adjust the ambient lighting for
your viewing comfort.
♦=A viewing filter is recommended to reduce eye stress and fatigue.
Power On/Off Button
Power LED
Figure 2: The Workstation
3"
The AC Connection
— 4 —
The AC Connection
♦=Locate the AC port on the rear of the monitor (refer to Figure 3).
♦=Plug the female end of the AC cord into the AC port.
♦=Plug the male end into the power supply.
Figure 3: Connecting the Power Cord
The Signal Cable Connection
♦=Make sure that the monitor is powered Off. When powered off the
Power LED (see Figure 2) will not be lit.
♦=Locate the VGA port on the rear of the PC. The signal cable has a
standard 15-pin mini D-sub (VGA) connector. If you are having trou-
ble locating the VGA port, please refer to the documentation, which
came with your PC.
♦=Connect the Signal cable to the PC’s VGA port.
Figure 4: Connecting the Signal Cable
Chapter 1
— 5 —
Monitor Adjustments
The monitor is capable of both tilt and swivel adjustments.
Figure 5: Tilt Adjustment
♦=With the tilt feature, the monitor is capable of vertical adjustments of
+50°to -15°.
♦=The swivel feature allows for horizontal monitor adjustments of +45°to
-45°.
Figure 6: Swivel Adjustment
This concludes Chapter 1. The next chapter covers the on-screen display (OSD)
features.
50°
15°
50°
45°
— 6 —
Chapter 2
12 3 4
Contrast (and OSD Increase/Decrease) Control
When the OSD Main Menu is not engaged, turn the Contrast Control (1) to adjust the
display contrast level to accommodate the ambient lighting conditions of your specific
working environment. When the OSD Main Menu is engaged, turning this control
adjusts the display-setting values.
Brightness (and OSD On/Off) Control
When the OSD Main Menu is not engaged turn the Brightness Control (2) to adjust
the display brightness level. Pushing the Brightness Control calls up the OSD Main
Menu. Turn the control to scroll through the menu options.
Power LED
The Power LED (3) informs you of the monitor’s current operating status. The Power
LED will light Green when the monitor is powered On. In Standby mode the LED
lights Amber. When powered Off the LED is not lit.
Power On/Off Button
Push the Power Button (4) to power the monitor On or Off.
Contrast Brightness LED Power Button
F
i
g
ure 7:
F
unction Controls
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Sceptre Monitor Handbücher
Sceptre
Sceptre U435CV-UMR Bedienungsanleitung
Sceptre
Sceptre C27 Bedienungsanleitung
Sceptre
Sceptre U558CV-UMR Bedienungsanleitung
Sceptre
Sceptre C275 Bedienungsanleitung
Sceptre
Sceptre X23 Bedienungsanleitung
Sceptre
Sceptre X322 Series Bedienungsanleitung
Sceptre
Sceptre X405 Bedienungsanleitung
Sceptre
Sceptre X322BV-SR Bedienungsanleitung
Sceptre
Sceptre U550CV-UMR Bedienungsanleitung
Sceptre
Sceptre E246W-1080P Bedienungsanleitung
Sceptre
Sceptre X22 Bedienungsanleitung
Sceptre
Sceptre E328 SR Color Series Bedienungsanleitung
Sceptre
Sceptre U435CV-UMRD Bedienungsanleitung
Sceptre
Sceptre E325LD-MQR Bedienungsanleitung
Sceptre
Sceptre X240 Bedienungsanleitung
Sceptre
Sceptre U550CV-UM08R Bedienungsanleitung
Sceptre
Sceptre E408BD-FMQR Bedienungsanleitung
Sceptre
Sceptre E22 Bedienungsanleitung
Sceptre
Sceptre X325BV-FSR Bedienungsanleitung
Sceptre
Sceptre E20 Bedienungsanleitung
