Sceptre ST15 Bedienungsanleitung
i
PREFACE
About this manual
This manual is designed to assist you in setting up and using the LCD Monitor.
Information in this document has been carefully checked for accuracy; however,
no guarantee is given to the correctness of the contents. The information in this
document is subject to change without notice. This document contains
proprietary information protected by copyright. All rights are reserved. No part
of this manual may be reproduced by any mechanical, electronic or other means,
in any form, without prior written permission of the manufacturer.
Copyright
Copyright 1999, All Rights Reserved
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•=Reorient or relocate the receiving antenna.
•=Increase the separation between the equipment and the receiver.
•=Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•=Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturers may
void the user’s authority to operate this equipment.
i
i
NOTE:
A shielded-type power cord is required in order to meet the FCC emission limits
and also to prevent interference to the radio and television reception. It is
essential that only the supplied power cord be used.
Use shielded cables only to connect I/O devices to this equipment.
Canadian DOC Notice
For Class B Computing Devices
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B repecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
Cet appareil numérique de la classe B repecte toutes les exigences du Règlement
ii
i
Important Safety Instructions
Please read the following instructions carefully. This manual should
be retained for future use.
1. To clean LCD Monitor screen, first, make sure the Monitor is in the power off
mode. Unplug the Monitor from its power source before cleaning it. Do not
spray liquid cleaners directly onto the unit. Stand away from LCD Monitor and
spray cleaning solution onto a rag. Without applying excess pressure, clean the
screen with the slightly dampened rag.
2. Do not place LCD Monitor near a window. Exposing the Monitor to rain, water,
moisture or sunlight can severely damage it.
3. Do not lay anything on top of Monitor-to-PC signal cord. Make sure the cord is
placed in an area where it will not be stepped on.
4. Do not apply pressure to LCD screen. Excess pressure may cause permanent
damage to the display.
5. Do not remove the cover or attempt to service this unit by yourself. You may
void your warranty. Servicing of any nature should be performed only by an
authorized technician.
6. Safe storage of LCD Monitor is in a range of –20 ~ 60°C(or –4 ~ 140°F).
Storing LCD Monitor outside this range could result in permanent damage.
7. If any of the following occurs, immediately unplug your Monitor and call an
authorized technician.
•=Monitor-to-PC signal cord is frayed or damaged.
•=Liquid has been spilled into LCD Monitor, or it has been exposed to rain.
•=LCD Monitor has been dropped or the case has been damaged.
iv
Contents Of This Manual
Chapter 1 : Quick Installation 1
Chapter 2 : Installation
2.1 Unpacking 2
2.2 Positioning 3
2.3 Connecting the AC Power Adaptor 3
2.4 Setting Up the LCD Monitor 5
2.5 Power Management System 5
Chapter 3 : Display Controls
3.1 User Controls and Indicator 6
1
CHAPTER 1
Quick Installation
1. Read Important Safety Instructions section thoroughly
(on page iii, Preface of this manual) before installing LCD
Monitor.
2. Make sure your computer system and LCD Monitor are both turned
off before any cable connection started.
3. Connect signal cable to the computer .
4. Connect the power cord into the jack of LCD Monitor and plug the
other end of power cord into a wall socket.
5. Turn the computer on.
6. Turn on LCD Monitor DC power switch at the rear of monitor.
And now that, installation has been completed enjoy your LCD Monitor .
2
CHAPTER 2
Installation
2.1 Unpacking
Before you unpack LCD Monitor, prepare a suitable workspace for your
Monitor and computer. You need a stable and clean surface near a wall
power outlet. Also ensure that LCD Monitor has enough space around it to
allow for airflow. Even though LCD Monitor uses very little power, some
ventilation is needed to ensure that the Monitor doesn’t become too hot.
After you unpack LCD Monitor, make sure the following items are
included in the box and in good condition.
♦=LCD Monitor mounted on its stand
♦=Monitor-to –PC 1.8M signal cable
♦=AC Adaptor
♦=Power cord
♦=This user’s manual
If you find that any of these items is missing or appears damaged, contact
your dealer immediately. Do not throw away the packing material or
shipping carton in case you need to ship or store LCD Monitor in the
future.
3
2.2 Positioning
Take a moment to prepare a suitable place to set up your workstation. You
need a stable flat dust-free surface with good ventilation. Even though LCD
Monitor has been designed using components that don’t use much power,
they still generate quite a bit of heat. Set up your LCD Monitor so that the
screen doesn’t face a window where sunlight often comes in. The reflection
of sunlight makes LCD Monitor screen difficult to read or view.
Warning!
•=When positioning the equipment, make sure that the main ports and sockets
are easily accessible.
•=Do not place your LCD Monitor close to a heat source.
•=Do not place the LCD Monitor in direct sun light or near a window. Moisture
and direct sunlight exposure may cause LCD monitor serious damage.
2.3 Connecting the AC Power Adaptor
1) Connecting the Power Cord to the AC Adaptor.
Plug the power cord into the receptacle of the Adaptor.
This power connector plugs into the LCD Monitor’s power conn port.
4
2) Connecting the AC Adaptor to the monitor.
Plug the adaptor’s power connector into the monitor.
3) Connecting the power cord to an AC power source
Your power outlet (mains)
connecting may be different from
that shown here.
The plug should match the standard
for your area.
The plug on the power cable will
vary according to the electrical
standard for your area.
NOTE: DO NOT remove or defeat the plug ground (the third prong)
Note, for added protection, we recommend you use a “Surge Protector” device
plugged between the AC Adaptor and the electrical wall outlet to prevent the
effects of sudden current variations from reaching the LCD Monitor. The sudden
peaks of electricity are not good for the Moniotr.
5
2.4 Set Up the LCD Monitor
Please follow the steps below to set up the LCD Monitor.
1) Step 1: Connect the Power Cord into the AC Adaptor.
2) Step 2: Connect the Power Connector cable between the AC Adaptor
and the LCD Monitor connector port located on the rear side of the
LCD Monitor.
3) Step 3: Plug the Power Cord from the adaptor into an electrical wall
outlet.
4) Step 4: Turn “ON” the LCD Monitor’s Power Switch.
2.5 Power Management System
This LCD Monitor complies with the VESA DPMS (version 1.0p)
power management proposal. The VESA DPMS proposal provides
four phases of power saving modes by detecting horizontal or vertical
sync signal. Please refer to Power Management section of
Specification on Appendix for power consumption at each different
mode.
When LCD Monitor is in the power saving mode, monitor screen will
be blank and power LED indicator shows color in amber.
6
CHAPTER 3
Display Controls
3.1 User Controls and Indicator
Operation of LCD Monitor is quite simple due to its intuitive,
ergonomic design. A description for each of LCD Monitor function
controls and indicator is provided below. Figure 3-1 shows the
function controls as seen on the front panel of the Monitor.
Figure 3-1: Function Controls and Indicator
3
2
1
Inhaltsverzeichnis
Andere Sceptre Monitor Handbücher
Sceptre
Sceptre X22 Bedienungsanleitung
Sceptre
Sceptre U27 Bedienungsanleitung
Sceptre
Sceptre X270 Bedienungsanleitung
Sceptre
Sceptre U658CV-UMR Bedienungsanleitung
Sceptre
Sceptre X322BV-SR Bedienungsanleitung
Sceptre
Sceptre C328W-1920R Bedienungsanleitung
Sceptre
Sceptre E195BV-SRR Bedienungsanleitung
Sceptre
Sceptre X 7G Naga V X7g-NagaV X7g-NagaV Bedienungsanleitung
Sceptre
Sceptre X405BV Bedienungsanleitung
Sceptre
Sceptre U515CV-UMR Bedienungsanleitung
Sceptre
Sceptre LCD Monitor X9S-NagaV Bedienungsanleitung
Sceptre
Sceptre X22 Bedienungsanleitung
Sceptre
Sceptre E27 Bedienungsanleitung
Sceptre
Sceptre U415CV-UMS Bedienungsanleitung
Sceptre
Sceptre E325 Bedienungsanleitung
Sceptre
Sceptre X322BV-SRN Bedienungsanleitung
Sceptre
Sceptre E328BD-SR Bedienungsanleitung
Sceptre
Sceptre U435CV-UMRD Bedienungsanleitung
Sceptre
Sceptre U505 Series Bedienungsanleitung
Sceptre
Sceptre X325BV-FSR Bedienungsanleitung
