Schäfer draft2go Bedienungsanleitung
Foreword
draft2go
BA-49-001-09
1 von 21
Operating instructions
draft2go
dispensing system
Foreword
draft2go
BA-49-001-09
2 von 21
1 Foreword
The operating instructions contained in this manual must be followed for
•Transport
•Commissioning
•Handling
•Maintenance
ATTENTION
Before working with the draft2godispensing sys-
tem, the user / operator must have read and un-
derstood this manual.
This manual, and in particular the safety instructions, must be observed at all times by all
people working on or with the draft2go dispensing system. In addition, all rules and regulations
for accident prevention which apply at the place the container is used, as well as all national
directives (e.g. industrial safety regulations) must be complied with.
It is advisable to keep a copy of this instruction manual at all places where the draft2go dis-
pensing system is being used.
Only original replacement parts may be used.
Table of Contents
draft2go
BA-49-001-09
3 von 21
2 Table of Contents
1Foreword ............................................................................................................................. 2
2Table of Contents ................................................................................................................. 3
3Introduction and basic safety instructions ............................................................................. 4
3.1 Explanation of signs and symbols.................................................................................. 5
4The draft2go dispensing system............................................................................................ 7
4.1 Components of the draft2go dispensing system ............................................................ 8
5Assembly and commissioning ............................................................................................... 9
5.1 Explanation of various components .............................................................................. 9
5.2 Assembling the insulating jacket with KEG .................................................................... 9
5.3 Assembling the dispensing head ................................................................................. 10
5.3.1 Tappet and one-way line............................................................................................................... 10
5.3.2 Attaching the dispensing head to the draft2go KEG ..................................................................... 10
5.3.3 Fitting the beer line to the dispensing head ................................................................................. 11
5.4 Commissioning........................................................................................................... 14
5.5 General tips for tapping beer...................................................................................... 16
6Disassembly and Cleaning .................................................................................................. 17
6.1 Disassembly............................................................................................................... 17
6.2 Cleaning..................................................................................................................... 18
6.2.1 Cleaning the dispensing head ....................................................................................................... 18
6.2.2 Cleaning the insulation.................................................................................................................. 19
7Beverage residues in the draft2go KEG................................................................................ 20
8. Trouble shooting .................................................................................................................... 21
Contact: ..................................................................................................................................... 21
Introduction and basic safety instructions
draft2go
BA-49-001-09
4 von 21
3 Introduction and basic safety instructions
This operating instruction manual serves as the basis for using and operating the draft2go
dispensing system.
PLEASE NOTE
This instruction manual provides information on how to use the
draft2go dispensing system safely. The knowledge and application
of the information described here is absolutely essential to guaran-
tee the appropriate and error-free use of the draft2go system.
Failure to comply with the operating instructions may result in errors that can damage the
dispensing system or lead to the risk of accidents and consequently injury to other persons.
WARNING
The manufacturer refuses to accept any liability arising from use of
the draft2go dispensing system, if the safety instructions contained
in this operating manual have been disregarded.
The draft2go dispensing system may only be operated by persons,
who have read and fully understood this operating manual.
Introduction and basic safety instructions
draft2go
BA-49-001-09
5 von 21
3.1 Explanation of signs and symbols
PROHIBITED
This sign is used to describe a prohibition instruction that must be
followed.
Failure to comply with the information can lead to material damage
as well as slight or moderately serious injury.
WARNING
Indicates a potentially dangerous situation.
Failure to comply with this instruction can lead to material damage
as well as slight or moderately serious injury.
INSTRUCTION
Indicates a rule or instruction that must be followed.
PLEASE NOTE
Indicates general information, useful tips for users and working rec-
ommendations.
Introduction and basic safety instructions
draft2go
BA-49-001-09
6 von 21
Prohibiting signs
Prohibited!
No direct sunlight
Warning signs
Danger warnings!
Instructions
Information signs
Read the instruction manual
The draft2go dispensing system
draft2go
BA-49-001-09
7 von 21
4 The draft2go dispensing system
Thank you for choosing the draft2go dispensing system.
draft2go is an all-in-one dispensing system which is op-
erated without the dispensing technology usually re-
quired in hospitality businesses. Using it for any purpose
other than that described in this operating manual is
considered improper use.
The draft2go system consists of a two-chamber KEG with
gas and beer compartments, an insulating jacket and a
dispensing head.
The KEG is equipped with a flat fitting for the beer com-
partment and an NC valve for the gas compartment.
The draft2go dispensing head is made of high-quality plastic and all components coming into
direct contact with the beer are food-safe.
The flow of beer from the draft2go dispensing head is interrupted by compression of the beer
line tube.
The full KEG should be pre-cooled to 2 - 4°C. At this temperature, the insulating jacket keeps
the KEG at the usual drinking temperature in northern Europe of 4 to 8°C for up to 8 hours. If
the beer is too warm, this can result in excessive foam.
If the KEG is being kept in a standard refrigerator, the manufacturer’s recommend cooling
the KEG at 2°C for 24 hours before use.
PROHIBITED
The draft2go dispensing system must not be exposed to direct sun-
light and temperatures of above 30°C.
The draft2go KEG must never be placed in a deep freeze to cool it
down.
The draft2go dispensing system
draft2go
BA-49-001-09
8 von 21
4.1 Components of the draft2go dispensing system
Delivery scope
draft2go set
The draft2go-KEG is not in-
cluded in the delivery scope.
Item
KEG
Item
Insulation
Item
Dispensing head
1
draft2go KEG
2.1
Insulating base
3.1
Dispensing head
2.2
Drip tray
3.2
Tappet
2.3
Drip tray grill
3.3
One-way line
2.4
Insulating jacket
3.4
Faucet spout
3.5
Operating instructions
3.1
2.4
3.4
2.3
2.2
3.3
3.2
1
2.1
Assembly and commissioning
draft2go
BA-49-001-09
9 von 21
5 Assembly and commissioning
5.1 Explanation of various components
Tap Lever
Stainless steel
faucet spout
NC valve Flat fitting
5.2 Assembling the insulating jacket with KEG
Place the pre-chilled KEG onto the insula-
tor base, so that the NC valve and the re-
cess in the top ring are in line with the drip
tray. Slide the drip tray into place on the
base.
The draft2go dispensing system must al-
ways be placed on a stable surface.
Fit the drip grill into place inside the
drip tray.
Assembly and commissioning
draft2go
BA-49-001-09
10 von 21
5.3 Assembling the dispensing head
5.3.1 Tappet and one-way line
Rinse out the tappet and the beer line under cold running water before
every use. This is easiest when the two components are assembled.
5.3.2 Attaching the dispensing head to the draft2go KEG
ATTENTION
Always attach the dispensing head so that the flat
fitting and the NC valve can be coupled to it.
Put the two sides of the insulator
jacket together, so that the hand-
holds on the jacket are in line with
those on the KEG.
Press the dispensing head onto the flat fitting
and the NC valve and pull it forward until the
dispensing head clicks into place. A clicking
sound can be heard.
Inhaltsverzeichnis
