Schacht Wolf Pup Bedienungsanleitung

WOLF PUP LOOMTM

& WOLF PUP LT LOOMTM

Assembly InstructIons

FL3000

FL3006

FL3009

Find out more at schachtspindle.com

Schacht Spindle Company 6101 Ben Place Boulder, CO 80301

p. 303.442.3212 f. 303.447.9273

WOLF PUP

WOLF PUP LT

– 2 –

WOLF PUP &WOLF PUP LT

Assembly InstructIons

BEFORE YOU BEGIN

■All Wolf looms assemble in a similar way. Watch the Baby Wolf assembly video on our

Youtube channel (www.youtube.com/user/schachtspindle).

■You’ll nd a complete labelled diagram of the Wolf loom in your Maintenance and

Warranty manual and at schachtspindle.com.

■Wolf loom legs are called out by where they cross each other. The legs that touch the

ground at the front of the loom are called “inside” legs because they are covered by the

“outside” legs when they cross at the loom center.

■The beater is at the front of the loom.

■The brake is on the right side of loom.

beater

brake

outside

leg

inside

leg

fold knob

brake release

pedal

ratchet

advance lever

ratchet gear

ratchet pawl

– 3 –

Hardware bag 2:

1X 3/8" cap nut for warp beam crank

handle

1X 3/8" washer for warp beam crank

handle

3X extra 8/32" hex nuts for shafts

2X #12 SAE washers

2X 1/4-20 slim lock nuts

2X 1/4-20 x 2" Phillips truss head

machine screws

2X 1" black spacers

TOOLS

#2 Phillips screwdriver

5/8" and 7/16" or adjustable wrenches

string

masking tape (optional)

PARTS

Wrapped onto warp beam:

3X apron bars

2X lease sticks (with holes)

1X front beam extension

8X heddle bars

Accessory pack:

1X brass reed hook

1X warp beam crank handle

8X 29" apron cords (or 2X 12-foot

apron cords for cherry looms)

2X wheels

1X Treadle Tracker

300X heddles

24X tie-up cords (Pup LT only)

Maintenance and Warranty Manual

Hardware bag 1:

4X 1/4-20 x 1-1/2" Phillips truss

head machine screws

4X 1/4-20 lock nuts

3X 8-15 x 1-1/2" Phillips at head

sheet metal screws

UNFOLDING THE LOOM

1. Remove all plastic wrap from the loom.

Remove both shipping braces by slightly

loosening the back beam knobs and front

beam screws holding them in place. Discard

the braces and tighten the knobs and screws.

Do not remove the string attaching the

beater to the castle.

2. Slightly loosen the black fold knobs on

each side of the loom (Figure 1). Generally, a

single turn will do.

Loosening the knobs all the way or

removing them can cause the loom to

collapse, which could result in injury.

3. Stand at the side of the loom. Hold the

front and rear beams as you allow the loom

to unfold all the way. Push the fold knobs to

the bottom of the slots and tighten them. FIGURE 1: UNFOLDING THE LOOM

slot in

castle

FRONT OF

LOOM

shipping brace

front

beam

screw

fold

knob

back

beam

knob

Phillips truss head

machine screw

washer lock nut slim lock

nut

cap nut

Phillips flat head sheet

metal screw

– 4 –

INSTALLING THE BEATER PEGS

4. Loosen the wing nuts holding the top

of the beater and remove the beater top.

Remove the reed from the beater.

5. Insert a 1/4-20 x 2" Phillips truss head

machine screw through a 1" black spacer,

then through the beater side from its

outer side (Figure 2).

6. From the inside of the beater, secure

the screw with a #12 washer and a 1/4-20

slim lock nut. You may nd it helpful to

hold the lock nut in place with a wrench.

7. Repeat on the other side of the beater.

After both pegs are installed, remove the

string tying the beater to the castle.

ATTACHING THE FRONT BEAM

EXTENSION

8. Use three 8-15 x 1-1/2" Phillips at

head sheet metal screws to attach the

front beam extension to the outside of the

front beam (Figure 3). It helps to lubricate

the screws with bar soap or paste wax.

ATTACHING THE WARP BEAM

CRANK HANDLE

9. The warp beam crank handle attaches

to a threaded rod on the inside right leg

(Figure 4). Locate the washer, cap nut,

and the warp beam crank handle in the

accessory pack. Place the 3/8" washer and

then the metal handle on the rod, with the

wooden handle facing out. Secure with the

the 3/8" cap nut.

When you’re weaving, the crank should

be pushed off of the cap nut. To engage

the crank for turning the warp beam, pull

the hexagonal hole in the crank onto the

cap nut.

FIGURE 2: INSTALLING BEATER PEGS

beater

side

1" black

spacer

1/4-20 x 2"

Phillips truss

head machine

screw

#12 SAE

washer

1/4-20 slim

lock nut

FIGURE 3: ATTACHING FRONT BEAM

EXTENSION

front beam front beam extension

8-15 x 1-1/2" Phillips flat head

sheet metal screws

FIGURE 4: ATTACHING WARP BEAM

CRANK HANDLE

3/8"

washer

cap nut

threaded rod

wooden

handle metal

handle

– 5 –

ATTACHING THE APRON BARS

For cherry Wolf looms, see the special

instructions for attaching the apron bars.

10. There is one cord for each hole in the

cloth and warp beams. Insert one end of a

cord through a hole in the beam and pull

the cord through. Then insert the other

end through the second hole in the end

of the cord that you just put through the

beam. Pull rmly on the cord to tighten

(Figure 5A). Repeat across the cloth beam

and the warp beam.

11. To attach the apron bar to the apron

cords, take a pinch of the cord about

4" from the end (Figure 5B). Insert the

pinched cord through the second hole in

the cord. Pull on the pinched cord until

a new loop forms that is large enough

for the apron bar to slip through (Figure

5C). Slide the apron bar through the loop

(Figure 5D) and pull tight. Repeat until all

cords are attached to the apron bar. Attach

the other apron bar to its beam in the

same way.

INSTALLING THE HEDDLES

12. Determine how many heddles you

want on each shaft. Count out the desired

number, then thread a string through the

holes at each end of the heddles and tie

them (Figure 6). String a group of heddles

for each shaft.

13. Slide each group of heddles onto a

pair of heddle bars (Figure 7). To make

threading easier, it is important to orient

the heddles in the same direction on each

pair of heddle bars.

On inserted eye heddles, the red end

of the heddles goes at the bottom for

left-handed threading or at the top for

right-handed threading.

14. Optional: To keep the heddles from

sliding around during the next steps, tape

each group of heddles to their heddle bars

with masking tape.

15. Lift the shaft frame closest to the front

of the loom and prop it up using a book

loop

FIGURE 5: INSTALLING APRON CORDS

A B

Visit youtube.com/user/schachtspindle for an

apron cord installation video.

FIGURE 6: THREADING HEDDLES ONTO

STRING

FIGURE 7: SLIDING HEDDLES ONTO

HEDDLE BAR

– 6 –

or small block of wood. The bottom of the

shaft frame should be raised 3 to 4 inches

(Figure 8).

16. Working from the rear of the loom,

lower a pair of heddle bars with heddles

into the castle in front of the raised shaft

frame.

17. Insert the heddle bars into the slots

on one side of the shaft frame. Bend the

heddle bars and insert the other ends into

the other sides of the shaft frame. Remove

the string ties and any tape you used.

18. Repeat Steps 16 through 17 on the

remaining shafts, working from the back

of the loom and adding heddles to shafts

from front to back of the loom.

WOLF PUP LT:

INSTALLING THE TIE-UP CORDS

19. There is one tie-up cord for each

hole in the lamms. Put the loop end of a

tie-up cord through each hole and pull the

button end through the loop until the cord

is secure against the lamm (Figure 9).

20. Tie the lamms to treadles by slipping

a tie-up cord into the slot in the treadle

(Figure 9). Work from the front lamm to

the rear lamm for each treadle. After you

have completed your tie-up, check each

treadle by pushing it all the way to the

oor and releasing it, making sure that the

knob of each tie-up cord is up against the

treadle and that each cord hangs straight

down to the treadle.

There is a 1/2" round depression on the

underside of each treadle end to prevent

the tie-ups from slipping off when the

loom is folded.

FIGURE 8: INSTALLING HEDDLE BARS

heddles

shaft frame

heddle bar

rear castle

cross brace

heddle bar

FIGURE 9: INSTALLING TIE-UP CORDS

lamm

tie-up

end of treadle (rear)

button

– 7 –

INSTALLING THE WHEELS

21. Skip this step if you will install a stroller

on your loom. With the loom unfolded,

install the wheels. Use two 1/4-20 x 1-1/2"

Phillips truss head machine screws and

two 1/4-20 lock nuts to attach each wheel

to the rear leg brace (Figure 10).

INSTALLING THE TREADLE

TRACKER

22. With the clip on the treadle tracker

facing the front of the loom, insert the

treadle tracker into the slot in the top of

the rear castle cross brace (Figure 11).

USING THE BEATER PIN

23. The small metal pin attached to the

inside right leg holds the beater upright

during warping. Leave the beater pin in its

holder when you’re weaving or folding the

loom (Figure 12A). To engage the pin for

warping, align the hole in the right outside

leg with the slot in the beater side. Insert

the pin through the hole and into the slot

(Figure 12B).

REMOVING THE BACK BEAM

24. The back beam can be removed for

better access to the heddles when you

thread the loom. Loosen the back beam

knobs on each side of the back beam and

lift the beam out (Figure 13). To replace

the back beam, slide the beam back into

the legs and tighten the knobs.

When you move the loom, be sure to

lift it using the cloth and warp beams,

not the front and back beams.

FIGURE 13: REMOVING BACK BEAM

back beam knob

FIGURE 11: INSTALLING TREADLE

TRACKER

slot

castle and shafts (viewed from above)

rear cross castle

brace

FIGURE 12: USING THE BEATER PIN

beater

hole

slot

beater side

right outside leg

FIGURE 10: INSTALLING THE WHEELS

1/4-20 x 1-1/2" Phillips truss

head machine screws

lock nuts

rear leg brace

(viewed from

back of loom)

– 8 –

Wolf PuP & PuP lt AccessorIes

WOLF TRAP

SECTIONAL BEAM

LOOM BENCH

ADJUSTING THE FRICTION BRAKE

25. The friction brake can be adjusted by

tightening or loosening the eye bolt. This

will increase or decrease the tension on

the spring, which will in turn increase or

decrease the tension on the brake bar and

the brake cable.

Always press down on the brake pedal

while you are winding on the warp

or advancing the warp on the cloth

beam.

FOLDING THE LOOM

26. To prevent treadles from dragging on

the oor when the loom is folded, attach

every treadle to at least one tie-up cord.

27. Start folding the loom: Loosen the fold

knobs one full turn and pull them up in

their slots (Figure 1, page 3).

28. With one hand on the rear beam and

one hand on the front beam, push the

loom together as far as it will go. Tighten

the fold knobs. •

FIGURE 13: ADJUSTING FRICTION BRAKE

eye

bolt

spring

brake bar

brake cable

WOLF STROLLER

HIGH CASTLE TRAY DOUBLE BACK BEAM

Andere Handbücher für Wolf Pup

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Schacht Weberei Handbücher

Schacht

Schacht CRICKET LOOM Bedienungsanleitung

Schacht

Schacht Wolf Pup 8.10 Bedienungsanleitung

Schacht

Schacht WOLF PUP & PUP LT Bedienungsanleitung

Schacht

Schacht WOLF PUP 8.10 LOOM Bedienungsanleitung

Schacht

Schacht TABLE LOOM Bedienungsanleitung

Schacht

Schacht Wolf Pup Installationsanleitung

Schacht

Schacht CRICKET QUARTET Bedienungsanleitung

Schacht

Schacht FLATIRON BULKY PLYER FLYER HEAD Kurzanleitung

Schacht

Schacht BABY WOLF FL3001 Bedienungsanleitung

Schacht

Schacht TL1105 Bedienungsanleitung

Schacht

Schacht Wolf Pup Bedienungsanleitung

Schacht

Schacht WOLF SECTIONAL BEAM Bedienungsanleitung

Schacht

Schacht Wolf Pup Bedienungsanleitung

Schacht

Schacht BABY WOLF FL3001E Bedienungsanleitung

Schacht

Schacht CRICKET QUARTET SL2045-05 Bedienungsanleitung

Schacht

Schacht CRANBROOK LOOM Bedienungsanleitung

Schacht

Schacht CRANBROOK Bedienungsanleitung

Schacht

Schacht FL3053 Bedienungsanleitung

Schacht

Schacht TL1105 Bedienungsanleitung

Schacht

Schacht WOLF PUP 8.10 HEIGHT EXTENDER Bedienungsanleitung

Schacht

Schacht SL2225 Bedienungsanleitung

Schacht

Schacht WOLF PUP 8.10 STROLLER Bedienungsanleitung

Schacht

Schacht FL3109 Bedienungsanleitung

Schacht

Schacht MIGHTY WOLF FL3002E Bedienungsanleitung

Beliebte Weberei Handbücher anderer Marken

Ashford

Ashford RIGID HEDDLE LOOM Bedienungsanleitung

AVL Looms

AVL Looms Dobby V Series Bedienungsanleitung

ROJ

ROJ SUPER ELF S3 Bedienungsanleitung

Louet

Louet Spring Bedienungsanleitung

Toyota

Toyota JAT810 Bedienungsanleitung

Toika

Toika JAANA Bedienungsanleitung

Leclerc Looms

Leclerc Looms COMPACT 4 SHAFTS Bedienungsanleitung

Leclerc Looms

Leclerc Looms VOYAGEUR Bedienungsanleitung

Toyota

Toyota JAT710 Bedienungsanleitung

Ashford

Ashford Katie Table Loom Bedienungsanleitung

Louet

Louet Jane Montageanleitung

Toyota

Toyota JAT810 Bedienungsanleitung

Ashford

Ashford WARPING FRAME - Large Bedienungsanleitung

Ashford

Ashford KIWI Bedienungsanleitung

Toika

Toika LAILA Bedienungsanleitung

Louet

Louet Delta Bedienungsanleitung

Leclerc Looms

Leclerc Looms COMPACT 8 SHAFTS Bedienungsanleitung

Louet

Louet David-III Montageanleitung