Schaefer DMD 30 Bedienungsanleitung
User Manual DMD 30/35
2
Kapitelbezeichnung
Kapitelbezeichnung
X.X Unterpunkt
SCHAEFER GmbH
Winterlinger Str. 4
72488 Sigmaringen
Germany
Phone +49 7571 722-0
Fax +49 7571 722-99
info@ws-schaefer.de
www.ws-schaefer.de
Support
If you have any questions regarding this product please contact:
Phone +49 7571 722-51
Fax +49 7571 722-99
Copyright
Duplication (copy, print, microfilm or any other form) as well
as electronic spreading of this document
is only permitted after formal writting consent of SCHAEFER GmbH.
SCHAEFER GmbH reserves the right to carry out alterations
of technical details without prior notice.
For all transactions our General Conditions of Sale
and Delivery shall be applicable.
All rights reserved.
Ress. 010708
Revision: 2009-12-08
3
Index
1 General description ................................. 4
2 Illustration ................................................ 4
3 Configuration ........................................... 5
4 Connection ............................................... 5
5 Programming ........................................... 6
5.1 Encoder or Connector?................................... 7
6 Settings ..................................................... 8
6.1 Input.......................................................................9
6.1.1 Coding ................................................................ 9
6.1.2 Connection ...................................................... 10
6.2 Dot-matrix ....................................................... 11
6.2.1 Presentation .................................................... 11
6.2.2 Frequency ........................................................ 12
6.2.3 Brightness | Intensity .................................. 13
7 Technical data ....................................... 14
8 Models ..................................................... 14
Index
User Manual Dot-Matrix Display DMD 30/35
4
1General description
DMD 30/35 range of dot-matrix display that can be
used as Position Indicators-, direction- or re-starting
Arrows, or a combination of both. The floor Position
as well as the direction arrows can be displayed as
follows: standing, flashing or scrolling.
The displays are available with one digit (DMD 30/35-
H1/V1), with two digits (DMD 30/35-H2/V2) or with
three digits (DMD 30/35-H3). The H1, H2 and H3 dis-
plays have there connections at the side of the display
(as Illustrated below) and the V1 and V2 displays are
connected from above.
All Displays are configured and adjusted by DIP swit-
ches located on the back of the Display. The indicating
characters/figures, including there functions can also
be configured by a PC using SCHAEFER DMD Config-
Kit and can be changed at any time. Two free-defined
special horizontally rolling texts messages (up to 14
characters) can be included. As from software version
2.6 on the DMD up to four special texts can be con-
figured.
General description | Illustration
2Illustration
Illustration
5
Configuration | Connection
3 Configuration
Two different kinds of configuration are possible:
• Configuration of the DMD 30/35 at SCHAEFER
according to the customer requirement
• Configuration of the DMD 30/35 on site.
Therefore a DMD-Config-Kit is needed
(article No. 010575).
4 Connection
In order to connect the DMD 30/35 you require either
a Connector PCB for Binary or Grey code or an Enco-
der PCB for signal per floor.
(including ribboncable 25 cm).
Article No.
Common anode (neg) Common cathode (pos)
Encoder 1 out of 15 008808 008809
Encoder 1 out of 31 008806 008807
Connector 008812
6
5.1 Encoder or Connector ?
Programming
5 Programming
The pin configuration can be modified via PC (DMD-
Config-Kit). Please note that the configuration of the
encoder cannot be changed, especially if pins were
defined as special text.
Pin configuration
5.1 Encoder or Connector ?
The table below gives you a general idea when an En-
coder PCB or Connector PCB should be used.
Depending on the number of Floors, horizontally rol-
ling messages and type of arrows or travel signal used
will depend on whether a connector or encoder is re-
quired.
Note: More than two special texts are
only possible as from software version 2.6
on the DMD.
Travel
GND
Down
Up
Adr 4
Adr 3
Adr 2
Adr 1
Adr 0
V in
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
10
9
8
7
6
5
4
3
2
1
7
5.1 Encoder or Connector ?
Programming
Horizon-
tally
Rolling
Messages
Floors
Codierung (control) Display possibilities
Dual/Gray 1 out of n Arrows Travelling
none
to 5 Connector Connector yes yes
6 to 15 Connector Encoder 1 out of 15 yes yes
16 to 31 Connector Encoder 1 out of 31 yes yes
1
to 4 Connector Connector yes yes
5 to 15 Connector Encoder 1 out of 15 und Connector yes yes
16 to 31 Connector Encoder 1 aus 31 yes no
2
to 3 Connector Connector yes yes
4 to 7 Connector Encoder 1 out of 15 und Connector yes yes
8 to 15 Connector Encoder 1 out of 15 und Connector yes no
16 to 31 Connector Encoder 1 out of 31 no no
3*
to 2 Connector Connector yes yes
3 Connector Encoder 1 out of 15 und Connector yes yes
4 to 7 Connector Encoder 1 out of 15 und Connector yes no
8 to 15 Connector Encoder 1 out of 15 no no
16 to 31 Connector Encoder 1 out of 15 no no
4*
to 2 Connector Connector yes no
3 Connector Encoder 1 out of 15 und Connector yes no
4 to 7 Connector Encoder 1 out of 15 und Connector no no
8 to 15 Connector Encoder 1 out of 15 und Connector no no
16 to 31 Connector no
* Mehr als zwei Sondertexte erst ab SW-Version 1.5 auf der DMD 27 möglich.
8
Settings
6Settings
Different settings can be changed on the display by
means of the buttons and respective DIP switches.
The values are changed by the DIP switches and adju-
sted by the buttons e. g. the brightness of the display
can be adjusted as follows:- Switch the Dot Matrix Dip
switch No3 to the on position. Press the Dot Matrix
button until the required brightness is selected. The
setting is saved after the corresponding DIP switch
has been turned off.
DIP switches
Dot-matrix
DIP switches
Input
Indicator
Dot-Matrix
Button
Input Status
LED
1 2 3 4 1 2 3 4
Input
Button
9
Settings
6.1 Input | 6.1.1 Coding
6.1 Input
6.1.1 Coding
With DIP switch Input 1 in the on position the co-
ding type can be adjusted. By pressing the Input
button the different coding type can be selected. The
Status LED shows the present status. Switch off the
DIP switch to save the selection.
LED: yellow
Binary
LED: yellow
green
1 out of n
(signal per floor)
LED: green
Gray
Button
Button Button
10
Settings
6.1.2 Connection
6.1.2 Connection
DIP switch Input 2 controls the switching variant. By
switching the DIP switch to the on position and pres-
sing the input button, the display can be switched to
common cathode (positive switching) or common an-
ode (negative switching).
Button
LED: yellow
Common
cathode
(Positive switching)
LED: green
Common
anode
(Negative swithing)
Button
DIP switches Input 3 and 4 are reserved for later func-
tions and have no effect.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Schaefer Monitor Handbücher
