Schlage RP200 Bedienungsanleitung
Introduction
The RP200 Light Module works as both a light controller and a signal repeater
to help extend the range of your Z-Wave™ network.
Please go to http://monitoringcontrol.verizon.com and follow the simple steps
provided in the online setup wizard. This will enable you to add your Light
Module to the Home Control Network.
FOR INDOOR USE ONLY!
DO NOT use with non-resistive loads, such as fluorescent lighting, CFL
bulbs or motors.
To reduce the risk of electric shock, this product has a grounding type
plug that has a third (grounding) pin. This plug will only fit into a grounding
type power outlet. If the plug does not fit into the outlet, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Any modification or use other than described may damage the unit and
will void the warranty.
RP200 Light Module
User Guide
Installation
1. Plug the light module into any available outlet.
• The light module can be used to control a lamp.
• The light module repeats the Z-Wave signal. In some homes, the light
module may be used to improve communication between the gateway
device and other Z-Wave devices.
• The light module should be installed into any indoor, three-prong, 120
volt A/C outlet.
2. (Optional) Plug a lamp into the Z-Wave (two-prong) side of the light
module.
• There are two outlets on the light module. One of the outlets has only
two prongs and is labelled with a Z-Wave™ sticker. A lamp (25 watts
minimum and 300 watts maximum) can be controlled by the system if
it is plugged into the Z-Wave™ side of the light module.
• Use only an incandescent light bulb in the lamp that is plugged into
the light module. DO NOT use a CFL (compact fluorescent light bulb)
or any other kind of electric device.
• The other outlet has three prongs and can be used simply as a
pass-through outlet (1500 watts maximum). It is not controlled by the
system, and the system is not affected when it is used.
Max. 300W
Incandescent
Z-Wave™
Side
Pass-through
Side
1
2
©2010 Schlage Lock Company
Verizon RP200 Rev. 12/10-2
Manual Operation
• Press the button once to turn the light on or off.
• Press and hold the button to dim.
• Use the web portal, TV widget or phone application for remote control.
• The pass-through outlet (1500 watts maximum) is not controlled by the
system, and the system is not affected when it is used.
Click or
Hold
Z-Wave™
Side
Pass-through
Side
Specifications
• Power 120 VAC, 60 Hz
• Signal (Frequency) 908.42 MHz
Software Fuse
The RP200 is designed to protect itself against loads that exceed
it’s maximum power rating. The application of a load that exceeds
that rating is quickly sensed by the dimmer and it responds by
immediately shutting off all power to that load. If the dimmer
doesn’t seem to work, or if it only works momentarily, check to
see that the total light wattage doesn’t exceed the 300W rating of
the RP200. If a properly sized load is restored to the dimmer, it
can be operated normally once again.
Over-current protection
The RP200 hardware has an over current detection circuit, which
is final protection against overload. If the software fuse should
fail to shut down the dimmer when overloaded, backup protection
is provided by an internal fuse. This fuse is not user serviceable.
Check your home circuit breakers before concluding that the
product must be returned to the manufacturer for repair at a
nominal charge.
FCC NOTICE
Note: This equipment has been
tested and found to comply
with the limits for a Class B
digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection
against harmful interference
in a residential installation.
This equipment generates,
uses, and can radiate radio
frequency energy and, if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.•
• Increase the separation between the equipment and
receiver.•
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.•
• Consult the dealer or an experienced radio/TV technician for
help.•
IC NOTICE
This Class B digital
apparatus complies
with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
About RP200’s Certification
In addition to compliance with product
safety standards, the RP200 is also
certified to comply with applicable FCC
and IC rules and regulations governing
RF and EMI emissions.
Inhaltsverzeichnis
Andere Schlage Dimmer Handbücher
