Schleifenbauer PDU Bedienungsanleitung



 

V2.52 Schleifenbauer PDU

User manual



Page 1 of 54

V252_User manual

Schleifenbauer PDU




Index 

Layout of this manual 4
UC_What’s new 4
Introduction 5
Power distribution meets intelligence 5
Interfaces 5
Accessories 5
Colored housing 6
Measurements 6
Part I - Installation of hardware 7
Safety warnings 7
Expert personnel 7
Technical installation requirements 7
Visual inspection 7
Testing 8
Cleaning 8
Contents of the package 8
Additionally needed tools 8
Mounting the PDU in cabinets 8
How to mount a PDU horizontally (19 inch)? 8
How to mount a PDU vertically (= 0U)? 9
How to install on a flat surface?...table top mount 9
How to prevent hot spots in a cabinet? …sunken installation
9
How to mount a PDU without tools? 9
How to achieve maximum mounting flexibility? ...mounting
with profile clamps 9
Cabling the PDU: ethernet, databus and sensors 10
How to connect the PDU to LAN? 10
How to connect a databus? 10
How to connect sensors to a PDU? 10
How to connect a NO/NC contact on Classic PDU and
ethernet PDU? 11
How to connect NO/NC contact on a g3 PDU? 11
Part II - User manual 12
How to maintain a PDU? 12
How to be sure the status of switchable outlets will not
change during firmware upgrade or restarting of the
controller? 12
Life-Supporting Policy 12
Part IIA - Locally monitoring: device display 13
How to change settings locally via PDU display? 13
How to stop a blinking display? … local alert reset 14
Why do alerts occur? 14
How to check the load balance, the temperature / humidity
or the status of the NO/NC contact? 14
How to get back to the first page? 15
How to check an outlet status locally? 15
How to check input and/or outlet measurements? 15
How to read measurements of optional sensors and what
options are possible? 16
Option 1: load page 16
Option 2: sensor pages 16
How to read Branch Residual Current measurements? 17
Data center practice: Residual Current Monitoring in
relation to Residual Current Devices 17
Where to measure residual current? 17
How to find the PDUs unit address, tag, name or location? 17
How to check the way the PDU is connected to the LAN? 18
How can I check in which mode and with what protocol the
PDU is running? 18
How to check the installed firmware version? 19
How to check for traceability information ? 19
Part IIB - Remote operating and monitoring: Web interface 20
Introduction 20
How to enlarge a pane in L sized screens? 21
How to select English or German language? 21
How to change and save settings in the web interface? 21
Dashboard – tab 22
System status 22
Load 25
Interfaces 25
Sensors – tab 26
Inputs – tab 27
Outlets – tab 28
System – tab 30
Identification 31
Configuration 32
Reset 32
Settings 33
Interfaces – tab 36
Part III - Administrator manual 37
Specific manuals 37
How to change SNMPv3 settings? 38
How to use the ‘connected devices’ section in the web
interface? 39
How to add new devices on an existing ring? How to solve
duplicate devices? 39
How about login profiles, usernames and passwords? 40
How to change factory passwords? 41
How to change the Ethernet link settings? 41
Network configurations 42
DHCP and default address 42
How to configure the IP settings manually? 42
How to setup IPv6? 43
IPv6 Autoconfigure (SLAAC) 43
Static IP 43
How to configure IPv6? 44
How to set up IPv6 address filtering? 45
How to send SNMP Traps with IPv6? 45
How to stop the alert signaling? ...auto reset alert 46
Firmware downgrade / upgrade 46
How to upgrade the firmware? ...using SPST 46
How to upgrade the firmware? ...using USB 47


Page 2 of 54
 V252_User manual
Schleifenbauer PDU




Schleifenbauer databus: what is it? 48

How to prevent data losses because of cable cuts? ...ring

redundancy 49

How to make a databus using Schleifenbauer Gateway? 50

How to connect the databus to LAN without a Gateway?

...using a PDU! 51

PART IV - Problem Solving 52

How to perform a “Software reset”? And why? 52

Remotely 52

Locally 52

How to perform a “Factory reset”? 52

How to reset peak current?.....and other dips or peaks 53

Recycling 54

PRODUCT SPECIFICATIONS 54

SERVICE AND SUPPORT 54



Page 3 of 54

V252_User manual

Schleifenbauer PDU



LAYOUT OF THIS MANUAL

This manual is split in three sections. You can focus on the section that fulfills your need when installing, operating and/or

managing the PDU.



The “How to....” section is meant to guide you directly to a solution for a problem you are faced with. It is not necessary to

read the complete manual.



Part I

Installation manual

Prepare PDU for use:



●safety issues

●mounting the PDU

●cabling the PDU



Part II

User manual

Operator and user part:



●operating/read out via the PDU-display

●operating/read out via the web interface

●problem solving



Part III

Administrator manual

Admin part:



●configure via the web interface

●set up via the web interface

●problem solving



Part IV

Problem Solving

In this chapter you can find the frequently asked questions

(FAQs)



WHAT’S NEW

●Firmware upgrade via USB port

●Near zero cross switching of outlet relays

●Support for 54 metered and/or switched outlets

●Voltage drop alert is now based on the input line voltage rather than a fixed value for 120 and 230 Volt operation.



Page 4 of 54

V252_User manual

Schleifenbauer PDU



INTRODUCTION

POWER DISTRIBUTION MEETS INTELLIGENCE

The Schleifenbauer Intelligent Power Distribution Unit (PDU) is designed to distribute power for many years and without

problems. It is equipped with a Schleifenbauer databus which makes it possible to read and manage many PDUs with a

single IP address. An ethernet port was added to the individual PDUs so that alongside the advantages of a databus, a

whole range of new options has become available.

Schleifenbauer PDUs bring together or merges the interests between IT and infrastructures, making it a real bridge builder.

The PDU may contain:

●metered outlets

●switched outlets

●metered and switched outlets

●passive outlets

Monitoring capabilities will be described in detail within this manual in coming sections.

INTERFACES

In the Admin part of this manual you will find information about the “Interfaces” with which we mean the technology to

communicate via your LAN with the Schleifenbauer databus. There are several possibilities:

●(embedded) web interface

●Modbus/TCP

●SNMP

(Simple Network Management Protocol)

●(SP)API

(Schleifenbauer Products Application Programming Interface)

ACCESSORIES

The following accessories can be purchased from Schleifenbauer, additionally. Please check the Installation Section for

more details regarding mounting brackets.

●C14/C20 plugs if C13/C19 outputs are used

●Different types of attachment brackets

o19” rack mounting brackets

oTabletop mounting brackets

oMounting plates for sunken installation

oProfile clamps

oToolless Mounts

●Customer Specific solutions related tools



Please check www.schleifenbauer.eu for further details regarding the accessories.

 



Page 5 of 54

V252_User manual

Schleifenbauer PDU



COLORED HOUSING



Standard the housing color of the Schleifenbauer PDUs is black. It is also possible to anodizing the housing in 5 other

colors.



01. black

02. green 

03. orange

04. blue

05. red

06. Yellow



Not shown but available is “natural”



Note:



actual colors may vary!

MEASUREMENTS

Measurements of the input and the outlet level can be found below:



Measurement

Unit

Remark

Energy

(kWh)

total & subtotal

Voltage

(V)

with voltage dip registration

Current

(A)

with peak value registration and drop detection.

Power factor

(%)



Apparent power

(VA)



Real power

(W)



Temperature

(°C)

with optional sensor

Relative humidity

(%)

with optional sensor

NO/NC contact

0-2

devices equipped with a USB-port can operate two NO/NC contacts

(see chapter “How to connect a NO/NC contact)



 



Page 6 of 54

V252_User manual

Schleifenbauer PDU



PART I - INSTALLATION OF HARDWARE

Please use the information in this chapter to inspect, install and connect the Schleifenbauer Intelligent PDU and all

optional mentioned accessories.



The PDU must be installed in a restricted access location

Socket-outlet must be installed near the equipment

Socket-outlet must be easily accessible

Installation by expert personnel only

After installation: default passwords / RC4 keys MUST be changed (see: Part III - Administrator manual)

SAFETY WARNINGS

This manual contains important safety instructions that should be followed during installation and operation of the PDU.

Please read this manual carefully since there may be serious or fatal personal injury and damage to the equipment if the

safety instructions, warnings and directions are not followed. Please save this document for future use.

EXPERT PERSONNEL

Installation, maintenance and inspection of the Schleifenbauer Intelligent PDU must be carried out by adequately trained

persons according to NEN EN 50110-1, with full observance of the specifications of NEN EN 50110-1 and NEN 3140.

TECHNICAL INSTALLATION REQUIREMENTS

Before installing and putting the system into operation, check whether the characteristics of the electrical system to which

connection is to be made correspond to the product specifications.

●The Schleifenbauer Intelligent PDU has been designed for connection to electrical systems that comply with IEC

60364 or in the Netherlands, NEN 1010.

●The voltage, maximum permitted current and the number of phases must be correct. This information is

displayed on the front side of the PDU.

●The maximum permitted power must be taken into account with regard to the maximum length and the diameter

of the connecting lead.

●The values and characteristics of the in-series protective devices must match the PDU and the protective

elements included in it.

●The environmental factors must correspond to the product specifications.

VISUAL INSPECTION

After opening the cardboard box and removing the packaging material, the PDU should be checked visually. The PDU

should not be put into operation if damage is detected such that safe and proper operation cannot be guaranteed. In such

cases, please contact Schleifenbauer Products BV.

Note that, in the case of PDUs that are equipped with an over voltage protection, the overvoltage protection and the

respective overcurrent protection (if applicable) must be inspected on a regular basis.



Page 7 of 54

V252_User manual

Schleifenbauer PDU



TESTING 

Each Schleifenbauer PDU is individually tested according to the NEN 3140 standard. Test reports are available on request.



For measurement of insulation resistance, the measuring voltage used must be lower than or equal to the

voltage according to the product specification.



CLEANING

The PDU may only be cleaned by wiping off the outside with a clean dry cloth.

CONTENTS OF THE PACKAGE

The Schleifenbauer Intelligent PDUs are shipped in a cardboard box. Where applicable, dispose the packaging material in a

responsible manner, in accordance with local regulations. All of the materials used for packaging can be recycled.

Immediately after receipt, check whether you have received all of the goods.



The following items are delivered for each PDU:

●fixing materials: these can be attached to the PDU (19’’ or table-mounting brackets), or are delivered separately if

they have been ordered separately;

●the installation manual (1 per shipment);



Please note that the PDU User Manual can be found online at http://schleifenbauer.eu

ADDITIONALLY NEEDED TOOLS

The following tools are needed to install the PDUs:

●cage-nuts with bolts and washers

●suitable screwdriver.

MOUNTING THE PDU IN CABINETS

How to mount a PDU horizontally (19 inch)?

Each 19’’ rack bracket of a PDU has holes for horizontal mounting in 19” racks. The holes are

positioned so that an appropriate fixing hole is always available for a PDU with a profile height of

1.5 U. Using one or two of the 4 holes allows mounting without wasting space.



 



Page 8 of 54

V252_User manual

Schleifenbauer PDU



How to mount a PDU vertically (= 0U)?

In the case of a PDU for vertical mounting, the connection lead is fed through a hole in the upper, bottom or front face.

There are 4 options for horizontal mounting:



How to install on a flat surface?...table top mount

Gives the profile possibility to be mounted to a flat surface (tabletop).This

arrangement is used for:

●vertical mounting to the bracing beams in the 19” cabinet

●fixing to a mounting plate

●mounting between the 19” uprights: the profile attaches to the front

of the uprights

The holes on the brackets are located as far as possible to the outside so

that it can also fit and tighten the bolts if a swivel gland has been placed

on the short side.



How to prevent hot spots in a cabinet? …sunken

installation

When power leads might block the flow of hot exhaust air, especially in

case of a 600mm wide cabinet, it is necessary to create flow space. This

can be done by using the “sunken installation brackets”. Because of the

shape of the bracket, it is possible to ‘partially sink’ the profile into the

cabinet and save space.

These mounting plates can be used for many different cabinets.



How to mount a PDU without tools?

Toolless mounting is created by making attachment points on the rear of

the PDU housing. There is a wide range of cabinet brackets available, all in

which you can hang the PDU without using tools.

Toolless Mounting can be done as single PDU or double PDUs (see photo).



Mounting brackets can be custom made by Schleifenbauer.



How to achieve maximum mounting flexibility?

...mounting with profile clamps

The clamps, made of spring steel, can be installed in the position of your

choice. The clamp fits around the PDU profile and is secured with a

fastening screw. Best is to use one clamp for every 50 cm of profile length.



Page 9 of 54

V252_User manual

Schleifenbauer PDU



CABLING THE PDU: ETHERNET, DATABUS AND SENSORS

How to connect the PDU to LAN?

10/100 Mbps LAN Ethernet port

Connecting the PDU to a Local Area Network (LAN) provides

communication through an Ethernet network, if the PDU is connected

exclusively, or simultaneously with the databus.

The RJ45 connector for the network cable must be plugged into the

Ethernet port:

●Connect the RJ45 Ethernet cable to the Ethernet port on the PDU

and to the Ethernet connector on the LAN device; when

connected, the orange LED – marked “lnk” - will blink



How to connect a databus?

There are three black communication ports. One is marked as sensorport,

the other two as databus ports (in and out).

The left databus port is the “incoming” databus port. The right databus

port is “outgoing”. This is a MUST HAVE for devices in bridge mode. For

devices in hybrid mode it is a NICE TO HAVE.

The serial databus in the Schleifenbauer PDU uses CAT5 patch cables.

The terms IN and OUT are arguable. Data will be send and received            

by both ports but to close the databus ring, it is recommended to follow             

the connection diagram. See it as the best way to daisy chain PDUs.



How to connect sensors to a PDU?

The PDU has a RJ12 connector sensor port for connecting a digital

temperature sensor, a combined sensor for temperature/humidity or one

or multiple dry switch contacts.



Plug and play

The PDU registers which sensor is connected and automatically adapts

the menu in the display to the sensor(s) that it has detected.



Use Schleifenbauer sensors only



Page 10 of 54

V252_User manual

Schleifenbauer PDU



Inhaltsverzeichnis

Andere Schleifenbauer Stromverteilungseinheit Handbücher

Schleifenbauer

Schleifenbauer V2.62 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung