SCHUNK ROTA-S flex 550 Gebrauchsanweisung

Translation of original operating manual

Manual chuck

ROTA-S flex

Assembly and Operating Manual

Superior Clamping and Gripping

Imprint

04|ROTA-S flex |en

Imprint

This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights

reserved. Any reproduction, processing, distribution (making available to third parties),

translation or other usage - even excerpts - of the manual is especially prohibited and

requires our written approval.

Technical changes:

We reserve the right to make alterations for the purpose of technical improvement.

Document number: 0889139

Version: 04 |01/04/2019|en

Dear Customer,

thank you for trusting our products and our family-owned company, the leading

technology supplier of robots and production machines.

Our team is always available to answer any questions on this product and other solutions.

Ask us questions and challenge us. We will find a solution!

Best regards,

Your SCHUNK team

H.-D. SCHUNK GmbH & Co.

Spanntechnik KG

Lothringer Str. 23

D-88512 Mengen

Tel. +49–7572-7614-0

Fax +49-7572-7614-1099

[email protected]

schunk.com

Table of contents

04|ROTA-S flex |en

Table of contents

General .................................................................................................................... 5

1.1

Warnings................................................................................................................... 5

1.2

Applicable documents .............................................................................................. 6

Basic safety instructions ........................................................................................... 7

2.1

Intended use............................................................................................................. 7

2.2

Not intended use ...................................................................................................... 7

2.3

Notes on particular risks........................................................................................... 8

2.4

Notes on safe operation......................................................................................... 10

2.4.1

Constructional changes, attachments or modifications............................. 14

2.5

Personnel qualification........................................................................................... 14

2.6

Organizational measures........................................................................................ 14

2.7

Using personal protective equipment.................................................................... 15

Warranty................................................................................................................. 16

Torques per screw ................................................................................................... 17

Scope of delivery ..................................................................................................... 17

Technical data ......................................................................................................... 18

6.1

Chuck data .............................................................................................................. 18

6.2

Clamping force / speed diagrams........................................................................... 19

6.3

Calculations for clamping force and speed ............................................................ 21

6.3.1

Calculation of the required clamping force in case of a given rpm............ 22

6.3.2

Calculation example: required initial clamping force for a given speed .... 24

6.3.3

Calculation of the permissible speed in case of a given initial clamping

force ............................................................................................................ 25

6.4

Grades of Accuracy................................................................................................. 26

6.5

Permissible imbalance............................................................................................ 26

Attachment of the entire manual chuck................................................................... 27

7.1

Handling prior to attachment................................................................................. 27

7.2

Preparing the chuck attachment............................................................................ 27

7.3

Assembly of the entire manual chuck .................................................................... 27

Function .................................................................................................................. 28

8.1

Handling and jaw change ....................................................................................... 28

8.2

Important notes on the ROTA-S plus or ROTA-S plus 2.0 manual chuck............... 29

8.3

Checking the ROTA-S plus or ROTA-S plus 2.0 manual chuck................................ 29

Maintenance ........................................................................................................... 30

9.1

Disassembling and assembling the chuck .............................................................. 30

Table of contents

04|ROTA-S flex |en

9.2

Jaw change ............................................................................................................. 30

9.3

At least once a month ............................................................................................ 31

9.4

In the case of decreasing clamping force or after approx. 200 operating hours .. 31

Spare parts.............................................................................................................. 32

Assembly drawing ................................................................................................... 33

................................................................................................................................ 34

................................................................................................................................ 35

................................................................................................................................ 36

................................................................................................................................ 37

General

04|ROTA-S flex |en

General

This operating manual is an integral component of the product and

contains important information on safe and proper assembly,

commissioning, operation, care, maintenance and disposal. This

manual must be stored in the immediate vicinity of the product

where it is accessible to all users at all times.

Before using the product, read and comply with this manual,

especially the chapter “Basic safety notes”.(2, Page 7)

If the product is passed on to a third party, these instructions must

also be passed on.

Illustrations in this manual are provided for basic understanding of

the product and may differ from the actual product design.

We accept no liability for damage resulting from the failure to

observe and comply with this operating manual.

Warnings

To make risks clear, the following signal words and symbols are

used for safety notes.

DANGER

Danger for persons!

Non-observance will inevitably cause irreversible injury or death.

WARNING

Dangers for persons!

Non-observance can lead to irreversible injury and even death.

CAUTION

Dangers for persons!

Non-observance can cause minor injuries.

NOTICE

Material damage!

Information about avoiding material damage.

1.1

General

04|ROTA-S flex |en

WARNING

Warning about hand injuries

WARNING

Warning about hot surfaces

Applicable documents

General terms of business

Katalogdatenblatt des gekauften Produkts

Calculation of the jaw centrifugal forces

("Technology" chapter in the lathe chuck catalog)

The above mentioned documents can be downloaded at

www.de.schunk.com.

1.2

Basic safety instructions

04|ROTA-S flex |en

Basic safety instructions

Improper handling, assembly and maintenance of this product may

result in risk to persons and equipment if this operating manual is

not observed.

Report any failures and damage immediately and repair without

delay to keep the extent of the damage to a minimum and prevent

compromising the safety of the product.

Only original SCHUNK spare parts may be used.

Intended use

The chuck is used to clamp workpieces on machine tools and other

suitable technical facilities, paying particular attention to the

technical data specified by the manufacturer. The technical data

specified by the manufacturer must never be exceeded.

The product is intended for industrial use.

Intended use also means that the user has read and understood

this operating manual in its entirety, especially the chapter “Basic

safety notes”.

The maximum RPM of the chuck and the required clamping force

must be determined by the user for the respective clamping task

based on the applicable standards and technical specifications of

the manufacturer.

(See also “Calculations for clamping force and RPM” in the chapter

“Technical data”). (6.1, Page 18)

Not intended use

A not intended use of the product is for example:

•It is used as a press, a punch, a toolholder, a load-handling

device or as lifting equipment.

•the product is used for unintended machines or workpieces.

•the technical data is exceeded when using the product.

(6.1, Page 18)

•if workpieces are not clamped properly, paying particular

attention to the clamping forces specified by the manufacturer.

•if it is used in working environments that are not permissible.

•if the product is operated without a protective cover.

2.1

2.2

Basic safety instructions

04|ROTA-S flex |en

Notes on particular risks

This product may pose a danger to persons and property if, for

example:

•It is not used as intended;

•It is not installed or maintained properly;

•The safety and installation instructions, local applicable safety

and accident prevention regulations or the EC Machinery

Directive are not observed.

DANGER

Possible risk of fatal injury to operating personnel if a jaw

breaks or if the lathe chuck fails because the technical data have

been exceeded and a workpiece is released or parts fly off

•The technical data specified by the manufacturer for using the

lathe chuck must never be exceeded.

•The lathe chuck may only be used on machines and facilities

that fulfill the minimum requirements of the EC Machinery

Directive; specifically, they must have effective technical

measures to protect against possible mechanical hazards.

DANGER

Possible risk of fatal injury to operating personnel from clothing

or hair being caught on the lathe chuck and being dragged into

the machine

Loose clothing or long hair may become caught on projecting

parts of the lathe chuck and be drawn into the machine.

•The machines and equipment must fulfill the minimum

requirements of the EC Machinery Directive; specifically, they

must have effective technical measures to protect against

potential mechanical hazards.

•Always wear tight-fitting clothing and a hairnet when working

on the machine and the lathe chuck.

2.3

Basic safety instructions

04|ROTA-S flex |en

DANGER

Risk to life and limb of the operating personnel in case of not

completely clamped workpiece and not removed Allan key

Risk to life and limb of the operating personnel and significant

damage of the machine due to the possibility of parts flying off.

•The machine spindle should only be started when the

workpiece is clamped and the Allan key is removed from the

chuck.

•Unclamping may only be possible when the machine spindle

has come to a standstill.

WARNING

Risk of injury due to dropping the chuck during transport,

installation or removal.

•Take special care in the danger zone when transporting,

installing or removing the chuck.

•Note the relevant load securing regulations for working safely

with cranes, ground conveyors, lifting gear and load-handling

equipment.

WARNING

Risk of injury by catapulted brass cover caps (accessory) of the

clamping bolt in case of rotation of the chuck.

The brass cover caps (accessory) of the clamping bolt must only

be used for stationary use of the chuck.

CAUTION

Danger of slipping and falling in case of dirty environment

where the chuck is used (e.g. by cooling lubricants or oil).

•Ensure that the working environment is clean before starting

assembly and installation work.

•Wear suitable safety shoes.

•Follow the safety and accident-prevention regulations when

operating the chuck, especially when working with machine

tools and other technical equipment.

Basic safety instructions

04|ROTA-S flex |en

CAUTION

Danger of limbs being crushed by opening and closing of the

chuck jaws during manual loading and unloading or when

replacing moving parts.

•Do not reach between the jaws.

•Wear safety gloves.

•Observe the safety and accident prevention regulations during

operation of the chuck, especially in connection with

machining centers and other technical equipment.

CAUTION

Risk of burns due to workpieces with high temperatures.

•Wear protective gloves when removing the workpieces.

•Automatic loading is preferred.

CAUTION

Hazard from vibration due to imbalanced rotating parts and

noise generation.

Physical and mental strains due to imbalanced workpieces and

noise during the machining process on the clamped and rotating

workpiece.

•Ensure the chuck's axial and concentric runout.

•Check options for remedying imbalances on special top jaws

and workpieces.

•Reduce the speed.

•Wear hearing protection.

Notes on safe operation

•The machine spindle should only be started when the

workpiece is clamped and the Allan key is removed from the

chuck.

•Only operate the chuck when all protective equipment has

been fitted and is in full working order.

•Check the manual chuck at least once per shift for externally

visible damage and faults.

2.4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SCHUNK Industrieanlagen Handbücher

SCHUNK

SCHUNK TCU-Z Gebrauchsanweisung

SCHUNK

SCHUNK ROTA THWvario Gebrauchsanweisung

SCHUNK

SCHUNK LDT-xS-0200 Gebrauchsanweisung

SCHUNK

SCHUNK FDB 150 Gebrauchsanweisung

SCHUNK

SCHUNK ZENTRICO THL plus Gebrauchsanweisung

SCHUNK

SCHUNK EGL Series Gebrauchsanweisung

SCHUNK

SCHUNK ROTA THW3 200 Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSR3 138 Gebrauchsanweisung

SCHUNK

SCHUNK TRIBOS SVP-2D Gebrauchsanweisung

SCHUNK

SCHUNK RPE 100 Gebrauchsanweisung

SCHUNK

SCHUNK MFT Gebrauchsanweisung

SCHUNK

SCHUNK SGB 32 Gebrauchsanweisung

SCHUNK

SCHUNK KGG 80 Gebrauchsanweisung

SCHUNK

SCHUNK KGG 60 Gebrauchsanweisung

SCHUNK

SCHUNK SVP-4 Gebrauchsanweisung

SCHUNK

SCHUNK LDL-US-0100 Montage- und Bedienungsanleitung

SCHUNK

SCHUNK DPZ 64 Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSE3 138-V1 Gebrauchsanweisung

SCHUNK

SCHUNK LGZ 16 Gebrauchsanweisung

SCHUNK

SCHUNK ROTA 2B Gebrauchsanweisung

SCHUNK

SCHUNK GAP Gebrauchsanweisung

SCHUNK

SCHUNK TCU-Z Gebrauchsanweisung

SCHUNK

SCHUNK ROTA NCE Gebrauchsanweisung

SCHUNK

SCHUNK GSW-M Gebrauchsanweisung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung

BAC

BAC BCP2D Bedienungsanleitung