SCHUNK VERO-S NSE-A3 Series Gebrauchsanweisung

Translation of Original Operating Manual

VERO-S quick-change pallet system

NSE-A3

Assembly and Operating Manual

Superior Clamping and Gripping

Imprint

2 02.00|1376941_NSE-A3 |en

Imprint

This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights

reserved. Any reproduction, processing, distribution (making available to third parties),

translation or other usage - even excerpts - of the manual is especially prohibited and

requires our written approval.

Technical changes:

We reserve the right to make alterations for the purpose of technical improvement.

Document number: 1376941

Version: 02.00 |09/12/2019|en

Dear Customer,

thank you for trusting our products and our family-owned company, the leading

technology supplier of robots and production machines.

Our team is always available to answer any questions on this product and other solutions.

Ask us questions and challenge us. We will find a solution!

Best regards,

Your SCHUNK team

H.-D. SCHUNK GmbH & Co.

Spanntechnik KG

Lothringer Str. 23

D-88512 Mengen

Tel. +49–7572-7614-0

Fax +49-7572-7614-1099

[email protected]

schunk.com

Table of contents

02.00|1376941_NSE-

A3 |en

Table of contents

General .................................................................................................................... 5

1.1

About this manual .................................................................................................... 5

1.1.1

Presentation of Warning Labels.................................................................... 5

1.1.2

Applicable documents................................................................................... 6

1.1.3

Design............................................................................................................ 6

1.2

Warranty................................................................................................................... 6

1.3

Scope of delivery ...................................................................................................... 7

1.4

Accessories ............................................................................................................... 7

Basic safety notes .................................................................................................... 8

2.1

Intended use............................................................................................................. 8

2.2

Not intended use...................................................................................................... 8

2.3

Constructional changes ............................................................................................ 8

2.4

Spare parts................................................................................................................ 9

2.5

Environmental and operating conditions................................................................. 9

2.6

Personnel qualification........................................................................................... 10

2.7

Personal protective equipment.............................................................................. 11

2.8

Notes on safe operation......................................................................................... 11

2.9

Transport ................................................................................................................ 12

2.10

Malfunctions........................................................................................................... 12

2.11

Disposal................................................................................................................... 12

2.12

Fundamental dangers............................................................................................. 13

2.12.1

Protection during handling and assembly .................................................. 13

2.12.2

Protection during commissioning and operation ....................................... 14

2.12.3

Protection against dangerous movements................................................. 14

2.12.4

Notes on particular risks ............................................................................. 15

Product description ................................................................................................. 18

3.1

Description of design and version.......................................................................... 18

3.2

Technical data......................................................................................................... 18

3.3

Technical data for coupling elements of media transfer unit................................ 19

Assembly................................................................................................................. 20

4.1

Pre-assembly .......................................................................................................... 20

4.2

Installing and connecting ....................................................................................... 20

4.3

Fastening and connection ...................................................................................... 22

4.3.1

Mounting..................................................................................................... 25

4.4

Clamping pins SPA 40, SPB 40, SPC 40, SPG 40 ...................................................... 27

4.4.1

Information to clamping pin SPG 40 ........................................................... 30

Table of contents

4 02.00|1376941_NSE-A3 |en

4.5

Clamping slide monitoring ..................................................................................... 30

4.6

Pneumatic circuit diagram...................................................................................... 33

4.7

Screw tightening torques ....................................................................................... 36

4.8

AFS 138 electronic monitoring systems (optional) ................................................ 36

Function .................................................................................................................. 37

5.1

KVS3 138 cone seal................................................................................................. 37

5.2

Media transfer unit................................................................................................. 38

Operation................................................................................................................ 39

Maintenance and care............................................................................................. 41

Troubleshooting ...................................................................................................... 42

8.1

The clamping area does not unlock ....................................................................... 42

8.2

The clamping area does not unlock properly......................................................... 42

8.3

The quick-change pallet system no longer opens quietly...................................... 42

8.4

If the clamping area does not unlock properly ...................................................... 42

8.5

Malfunctions when loading and unloading the change interface with fitted cone

seal.......................................................................................................................... 43

8.6

The cone seal does not seal ................................................................................... 43

8.7

The media transfer unit of the NSE3 138-P is not working.................................... 43

Wear parts set and parts lists .................................................................................. 44

9.1

Wearing part spare lists.......................................................................................... 44

9.2

Parts lists................................................................................................................. 44

Assembly Drawings ................................................................................................. 46

10.1

Assembly................................................................................................................. 46

10.2

Cone seal KVS3 138 ................................................................................................ 47

Translation of original declaration of incorporation................................................. 48

Appendix on Declaration of Incorporation, as per 2006/42/EC, annex II, No. 1 B ..... 49

General

02.00|1376941_NSE-

A3 |en

General

About this manual

This manual contains important information for a safe and

appropriate use of the product.

This manual is an integral part of the product and must be kept

accessible for the personnel at all times.

Before starting work, the personnel must have read and

understood this operating manual. Prerequisite for safe working is

the observance of all safety instructions in this manual.

Illustrations in this manual are provided for basic understanding

and may differ from the actual product design.

In addition to these instructions, the documents listed under

(1.1.2, Page 6) are applicable.

Presentation of Warning Labels

To make risks clear, the following signal words and symbols are

used for safety notes.

DANGER

Danger for persons!

Non-observance will inevitably cause irreversible injury or death.

WARNING

Dangers for persons!

Non-observance can lead to irreversible injury and even death.

CAUTION

Dangers for persons!

Non-observance can cause minor injuries.

NOTICE

Material damage!

Information about avoiding material damage.

1.1

1.1.1

General

6 02.00|1376941_NSE-A3 |en

Applicable documents

• General terms of business*

• Catalogue data sheet of the rotary indexing table *

• Technical data sheet for optional attachments *

The documents marked with an asterisk (*) can be downloaded on

our homepage schunk.com

Design

This guide applies to the following versions

Quick-Change Pallet System

• NSE-A3 138

• NSE-A3 138-V4

• NSE-A3 138-V4-P

• NSE-A3 138-V4-P1

• KVS3 138 cone seal

Warranty

The warranty period is 24 months after delivery date from factory

or 500 000 cycles*, if it is used as intended, under the following

conditions:

• Observe the applicable documents, (1.1.2, Page 6)

• Observe the ambient conditions and operating conditions,

(2.5, Page 9)

• Observance of the specified care and maintenance instructions

(7, Page 41)

Parts touching the workpiece and wear parts are not included in

the warranty.

* A cycle consists of a complete clamping process

("Open" and "Close").

1.1.2

1.1.3

1.2

General

02.00|1376941_NSE-

A3 |en

Scope of delivery

The scope of delivery includes

1 quick-change pallet system in the variant ordered

• 1 module accessory kit consisting of:

4 O-rings Ø 9 x 1.5

6 cover caps

6 fastening screws M8

1 fitting screw M8

• 1 cone seal accessory kit, consisting of:

1 O-ring Ø 6 x 5.5

1 O-ring Ø 110 x 1

• 1 operating manual

Accessories

(see catalog or data sheets when ordering separately)

• SPA40-(-16) cal, SPB-(-16), SPC-(-16), SPG clamping pins

• Plug (conversion)

• Weaker compression spring for cone seal

• AFS3 138 PMI monitoring system

• AFS3 138 MMS monitoring system

• SDE protection cover

• Coupling nipple for pallet

1.3

1.4

Basic safety notes

8 02.00|1376941_NSE-A3 |en

Basic safety notes

Intended use

This product and the compatible add-on components are intended

solely for positioning and clamping workpieces or clamping pallets

on machine tools or other suitable technical devices.

• The product may only be used within the scope of its technical

data, (3.2, Page 18).

• The product is intended for industrial and industry-oriented

use.

• Appropriate use of the product includes compliance with all

instructions in this manual.

Not intended use

The product is not being used as intended if, for example:

• It is used as a pressing tool, a toolholder, a load-handling device

or as lifting equipment.

• It is used for turning applications over 100 rpm without

consulting SCHUNK.

• It is used in working environments that are not permissible.

• People work on machines or technical equipment that do not

comply with the EC Machinery Directive 2006/42/EC,

disregarding the applicable safety regulations.

• The technical data specified by the manufacturer are exceeded

during usage.

Constructional changes

Implementation of structural changes

By conversions, changes, and reworking, e.g. additional threads,

holes, or safety devices can impair the functioning or safety of the

product or damage it.

• Structural changes should only be made with the written

approval of SCHUNK.

2.1

2.2

2.3

Basic safety notes

02.00|1376941_NSE-

A3 |en

Spare parts

Use of unauthorized spare parts

Using unauthorized spare parts can endanger personnel and

damage the product or cause it to malfunction.

• Use only original spare parts or spares authorized by SCHUNK.

Environmental and operating conditions

Required ambient conditions and operating conditions

Incorrect ambient and operating conditions can make the product

unsafe, leading to the risk of serious injuries, considerable material

damage and/or a significant reduction to the product's life span.

• Make sure that the product is used only in the context of its

defined application parameters, (3.2, Page 18).

• Make sure that the product is a sufficient size for the

application.

• Ensure the contact surfaces of the interface and recesses

towards the locating surfaces above the bolting points are kept

clean at all times.

• Under all circumstances, prevent any type of chips from

entering the interface and prevent cooling emulsion from

seeping into the interface. This may occur particularly during

vertical alignment of the clamping pin axis. The best way to

ensure both of these requirements is to use the SDE protection

covers or the cone seal provided for the quick-change pallet

system. If the interface should become filled with cooling

emulsion, initiate the unlocking process and allow the interface

to dry out while in an actuated state. It may be blown out

carefully with compressed air but only when using the required

protective equipment.

• Only use high-quality cooling emulsions with anti-corrosive

additives during processing.

• Protect the cone seal from high-pressure direct spraying with

cooling emulsion.

2.4

2.5

Basic safety notes

10 02.00|1376941_NSE-A3 |en

Personnel qualification

Inadequate qualifications of the personnel

If the personnel working with the product is not sufficiently

qualified, the result may be serious injuries and significant

property damage.

• All work may only be performed by qualified personnel.

• Before working with the product, the personnel must have read

and understood the complete assembly and operating manual.

• Observe the national safety regulations and rules and general

safety instructions.

The following personal qualifications are necessary for the various

activities related to the product:

Due to their technical training, knowledge and experience, trained

electricians are able to work on electrical systems, recognize and

avoid possible dangers and know the relevant standards and

regulations.

Due to its technical training, knowledge and experience, qualified

personnel is able to perform the delegated tasks, recognize and

avoid possible dangers and knows the relevant standards and

regulations.

Instructed persons were instructed by the operator about the

delegated tasks and possible dangers due to improper behaviour.

Due to its technical training, knowledge and experience, service

personnel of the manufacturer is able to perform the delegated

tasks and to recognize and avoid possible dangers.

2.6

Trained electrician

Qualified personnel

Instructed person

Service personnel of

the manufacturer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SCHUNK Industrieanlagen Handbücher

SCHUNK

SCHUNK PZH-plus 20 Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

SCHUNK

SCHUNK CLM Gebrauchsanweisung

SCHUNK

SCHUNK TENDO SVL Gebrauchsanweisung

SCHUNK

SCHUNK KGG 220 Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSE3 138-V1 Gebrauchsanweisung

SCHUNK

SCHUNK EGP 25 Anleitung zur Verwendung

SCHUNK

SCHUNK SRU-plus20-60 Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSR3 138 Gebrauchsanweisung

SCHUNK

SCHUNK SVP-4 Gebrauchsanweisung

SCHUNK

SCHUNK PZH-plus Gebrauchsanweisung

SCHUNK

SCHUNK ADHESO G-5-50-H Gebrauchsanweisung

SCHUNK

SCHUNK AOV-MC Gebrauchsanweisung

SCHUNK

SCHUNK TANDEM KSH3-LH Gebrauchsanweisung

SCHUNK

SCHUNK SWS-I-011 Gebrauchsanweisung

SCHUNK

SCHUNK EGS Series Anleitung zur Verwendung

SCHUNK

SCHUNK ROTA NCR 165 Gebrauchsanweisung

SCHUNK

SCHUNK ROTA NCK plus Gebrauchsanweisung

SCHUNK

SCHUNK MFT Gebrauchsanweisung

SCHUNK

SCHUNK GFS 16 Gebrauchsanweisung

SCHUNK

SCHUNK ROTA TP Gebrauchsanweisung

SCHUNK

SCHUNK SGB Gebrauchsanweisung

SCHUNK

SCHUNK VERO-S NSE-HT mini 88-20 Gebrauchsanweisung

SCHUNK

SCHUNK PZB-plus Gebrauchsanweisung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung

BAC

BAC BCP2D Bedienungsanleitung