Schweigen Endline Isodrive 1350 Bedienungsanleitung

02.2018 / V1.0 www.schweigen.com.au

INSTALLATION GUIDE

Endline Isodrive

System 1350

Page 2

Welcome

Thank you for purchasing your new Schweigen Endline Isodrive system.

To get the maximum output from the Isodrive 1350 motor, please read through this guide before use and

installation.

This guide contains important information on the correct use and maintenance of the unit, as well as important

safety notes. This will ensure your personal safety and the lasting value of your Isodrive system.

Please always retain your proof of purchase to aid in any warranty queries.

This appliance and its packaging are produced by processes that minimise waste and respect the environment.

Please help us to continue this eort to protect the environment by using the appliance eciently and dispose

of the packaging in a responsible manner.

Page 3

Index

1. Welcome _____________________________________________________________________________________ 2

2. Your Safety

Receiving your Isodrive Motor____________________________________________________________________ 4

Before Installation ______________________________________________________________________________ 4

Electrical Cord __________________________________________________________________________________ 4

Motor Features ________________________________________________________________________________ 5

General Notes on Installation and Use ____________________________________________________________ 5

Recommended Installation Distance _____________________________________________________________ 5

Minimum Mounting Height ______________________________________________________________________ 6

Avoidance of Back Flow _________________________________________________________________________ 6

Replacement of Supply Cord _____________________________________________________________________ 6

Why Flexi-duct _________________________________________________________________________________ 6

3. Description

Isodrive Motor - Box Contents ___________________________________________________________________ 7

Dimensions ____________________________________________________________________________________ 7

Installation Overview ___________________________________________________________________________ 8

4. Motor Installation

Wall Installation __________________________________________________________________ 8

Full Housing Assembly - Cross Section ____________________________________________________________ 10

Removable Motor Assembly _________________________________________________________ 11

Wall Aperture Cut Out ______________________________________________________________ 12

Motor Housing to Wall Fitment _______________________________________________________ 12

Front View of Motor Housing (view from behind front grille) _________________________________ 13

Installation using Optional Rear Clamp Assembly _________________________________________ 13

Attaching Optional Fire Ember Mesh Guard (Exploded view)__________________________________ 14

5. Flexible Ducting Installation

Flexible Ducting __________________________________________________________________ 15

Shallow Space ___________________________________________________________________ 15

Important Note __________________________________________________________________ 15

Securing Flexible Duct _____________________________________________________________ 16

6. Parts List

Parts List for Endline Isodrive 1350 Motor _______________________________________________17

7. Maintenance

Cleaning ________________________________________________________________________ 18

8. Specications/Warranty/Disclaimer ________________________________________________________ 18

Page 4

2. Your Safety

This appliance is not intended for use by person/s

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and/

or knowledge. Unless the person has been given

supervision or instruction concerning the use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they do

not play with the appliance, it is not a toy.

Do not install Isodrive motor to a non-Schweigen

and/or non-silent rangehood. If you fail to do so, your

warranty will be voided.

The manufacturer declines all responsibility in case of

failure to adopt proper safety measures.

Ensure that the location in which this appliance is

installed, has good and permanent ventilation.

Please consult local laws and regulations and install

in accordance.

Use an electrical connector with earth that is correct

for your location.

Check that the voltage in your area corresponds to

the appliance as indicated on the rating label.

Before Installation

We recommend this appliance to be installed or

repaired by a qualied Schweigen Home Appliances

technician.

Please see our website www.schweigen.com.au

for recommended installers.

It is dangerous to modify any part of this appliance.

Modication of any kind, will immediately void the

warranty.

Electrical Cord

Ensure the supply cord is not exposed to heat,

chemicals or sharp objects. If the supply cord is

damaged, it must be replaced by the manufacturer,

service agent or a similarly qualied person in order

to avoid a hazard. The power supply cord connection

MUST BE installed in such a way that access is easy

in case of emergency.

RECEIVING YOUR ISODRIVE MOTOR

Please read this section thoroughly before attempting to operate the appliance.

Inspect your product upon receipt. Any damage or defects MUST be reported

within 48 hours, or no claim will be recognised.

DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED.

If this product is installed damaged, the supplier, nor the retailer, will be responsible

for the costs associated with the repair, replacement, removal or re-installation of

the appliances.

Page 5

2. Your Safety

This guide is for the installation of the Isodrive motor

system after the rangehood has been mounted.

(Refer to rangehood installation manual on how to

install the rangehood).

NOTE: All exi ducting measurements are referring to

inside measurements, unless otherwise mentioned.

Motor Features

• IPX4 degree of weather protection.

• Super quiet, long vane, backward curved

centrifugal fan.

• Airow is dependant on installation and the

ducting used. Using single 200mm exi-duct will

deliver up to 1350m3/hr. The use of a smaller

than 200mm exi ducting would result in a

loss of airow and it is not recommended.

• Simple installation: Industrial quality motor and

fan made in Germany and rated at 40,000 hours.

• Motor is a high eciency PSC type and rated at

88W costing around the same as two 40W light

globes to run.

• WARRANTY 10 YEARS covers faulty

manufacturing or components. It does not cover

normal wear

and tear.

General Notes on Installation

and Use

This fan unit is designed to be installed using 200mm

exi ducting.

This fan is suitable for connection to ducting runs

with a minimum inlet area of 17,000mm2and length

up to 10m maximum (check with supplier if longer

duct length required). Where possible exible ducting

must be extended suciently to present a smooth

air passage with bends of at least the radii of twice

the diameter of the duct. Excessive bends in the

ducting will compromised extraction.

WARNING: The Endline Isodrive 1350 Motor System

must be installed into an external wall cavity. The

motor can not be installed into an internal wall

cavity or ceiling space where a build up of grease can

occur and become a potential re risk. This will void

warranty.

NOTE:Fan module and dual foil exi-duct are

acoustically matched. Use of semi-rigid or rigid

ducting will result in increased noise and may void

warranty. See installation instruction notes ‘Why exi-

duct’.

Recommended Ducting

Installation Distance

Schweigen recommends a length of 4 to 6 metres

of exi ducting, with at least 1 to 2 bends for optimal

performance. Any shorter distances may result

in higher airow noise. The maximum ducting

installation length is 10 metres. Check with supplier if

longer duct length is required. Do not reduce

the 200mm exi duct size at any time and avoid

sharp bends.

Page 6

Minimum Mounting Height

This fan unit is intended for mounting at a minimum

height of 2.1 metres (measured to the lower part of

the fan impeller) above a oor or the ground.

Avoidance of Back Flow

Care should be taken to avoid the back ow of gases

into the room from the open ue of gas or other open

re appliances.

Replacement of supply cord

If the supply cord is damaged, it must be replaced by

a service agent or suitably qualied person in order to

avoid a hazard.

NOTE: Do not use with a timer.

Why Flexi-duct?

Some internet sites strongly recommend the

use of rigid ducting over fully exible ducting.

This may well be the case with conventional

rangehoods with internal motors but not with

external motor rangehood.

Schweigen’s unique Isodrive system works in the

opposite way to conventional rangehoods, pulling air

through the hood and acoustically matched ducting,

producing almost silent high volume ow. The use

of a complete rigid or semi-rigid ducting system will

allow an organ piping eect to occur; like a didgeridoo

where a noise is produced at one end of a hollow rigid

pipe and the noise is amplied out the other.

The Isodrive system drives the noise outside the

house.

WARNING:

Installation without the use of at least the minimum

recommended length of acoustically matched

exi-ducting in the system will void performance

expectations. Any installation problem must be

reported to Schweigen. Call outs relating to incorrect

installation will result in a service fee direct to the

customer. Schweigen takes no responsibility for

problems caused by faulty installation, this may void

warranty.

A preferred installer list can be obtained from

Schweigen website www.schweigen.com.au or

by calling 1300 881 693.

2. Your Safety

Page 7

3. Description

Endline Isodrive System 1350

Included in the box:

1. Isodrive 1350 motor + housing

Approx. 5 metre, 10amp cable and standard male plug

2. Flexible ducting

Approx. 6 metres, 200mm (210mm OD1) diameter

3. Bell-mouth adopter ring 200mm

4. Back Draught Shutter

Not included in the box:

Optional Accessories

5. Fire guard - Part number: P3024

6. Rear mounting bracket - Part number: EL RMB

build assy

360mm

335mm

257 mm

372mm

360mm

440mm

372mm

257mm

21mm

395mm

21mm

Side viewAngle view

Dimensions

198mm

334mm

Page 8

4. Installation

Wall Installation

1. Remove the Endline Isodrive 1350 Motor System

from the packaging.

2. Undo the 2 screws holding front grille and the

deector, and remove them from housing (See

gure 1A, pg.10).

3. Remove the foam packaging material that is

behind the grille.

4. Remove the motor from the housing and set

safely aside before proceding with the installation:

Lift the motor mounting bracket side anges up

and over the locating stops and remove the motor

assembly (See Figure 1B and Figure 2 on page 11).

5. Cut a wall aperture with measurements of 340mm

horizontally and 265mm vertically ensuring the

vertical cuts are at 90 degrees to the horizontal

cuts (See Fig.3, pg.12); if you have less than

40mm of depth in the wall aperture — or the wall

requires extra stability for the motor housing to

be installed — you may need to reinforce the wall

with noggins and use the optional rear mounting

bracket (See Optional Accessories,

page 7, and Figure 6, page 13).

6. To prevent water ingress apply a high quality

adhesive sealant to the rear of the front ange of

the motor housing, ensuring that the entire gap

between ange and wall is sealed (See Figure

1A, pg10; and Figure 4, pg.12) and secure motor

housing to wall using 4 attachment screws (see

gures 1A, 4, 5). Remove excess sealant that is

extruded from the joint.

Male plug to rangehood plug

Motor Housing

Male plug to

mains power

Rangehood

Female plug

to motor

200mm exible ducting

Inside wall

Grille

Outside wall

1OD refers to outside dimension.

Installation Overview

Page 9

Note: If you require extra support to stabilise the

motor housing, you may use the optional accessory:

rear clamping assembly (attachment screws not

necessary), (see Fig.6, pg. 13).

7. Once the motor housing has been screwed and

tted securely to the wall. Insert the motor

assembly, making sure the internal electrical plug

is connected into the mounted power outlet inside

the housing (see Fig.1A, pg. 10, Fig.1B, & Fig.2,

pg.11).

8. Install the Front Grille and Deector, and secure

using grille attachment screws (see Fig. 1A, pg.10).

NOTE: A Fire Ember Mesh Guard may be required

when installing the Endline Isodrive 1350 Motor

System in a BAL (Bushre Assessment Level area).

This is an optional accessory (see pg.7 and Fig.7,

pg.14).

DO NOT increase the length of exi duct beyond

the recommended installation lengths. See

Recommended Installation Distance on page 5.

5. Installation

Page 10

5. Installation

Grille

Housing

attachment

screws

Deector

Completely seal the joint between outer ange and wall to prevent water ingress

into building. Seal the full perimeter using premium quality bonding urethane.

Base of housing has a one degree downwards slope from rear to front.

This will ensure drainage through the front grille drain holes

Anchor housing to wall structure by screwing through housing ange.

Ensure that ange perimeter is sealed against wall structure to prevent

water ingress into building

Vertical wall with suitable anchorage for housing

Removable fan and shutter assembly

Side rails -- Motor assembly support

Power supply

cord must be

at the top

1 Degree

Flange to locate

against stop

NB: Do not

cover or

restrict the

outlet.

Grille

attachment

screws

Stop

Air inlet

Note:

Minimum

inlet area

17,000 mm2

Duct attachment bellmouth

for 200mm ducting

Housing

attachment

screws

Figure 1A

Full Body Assembly Cross Section

Inhaltsverzeichnis

Andere Schweigen Belüftung Handbücher

Schweigen

Schweigen Hi Flow VX120 Bedienungsanleitung

Beliebte Belüftung Handbücher anderer Marken

Pichler

Pichler Ventech LG 150 Bedienungsanleitung

Hitachi

Hitachi RAF-50RPA Bedienungsanleitung

Daikin

Daikin FWF02B7TV1B Bedienungsanleitung

Paul

Paul santos 570 DC Bedienungsanleitung

Meltem

Meltem M-WRG-K Bedienungsanleitung

nilan

nilan Compact P Bedienungsanleitung

Whalen

Whalen VW series Montageanleitung

marinco

marinco N20803W Bedienungsanleitung

Venmar

Venmar Solo 1.5 Benutzerhandbuch

Xpelair

Xpelair Xplus2 EC RFH Bedienungsanleitung

Vents

Vents Micra 60 Bedienungsanleitung

Broan

Broan XB110H Bedienungsanleitung

Fantech

Fantech VHR704R Bedienungsanleitung

DewStop

DewStop Breeze Easy Bedienungsanleitung

DuraVent

DuraVent DCL Bedienungsanleitung

Broan

Broan HRVH100SE Bedienungsanleitung

Trane

Trane GGAA Montage- und Bedienungsanleitung

Miele

Miele AWG 102 Bedienungsanleitung