Scinomix Sci-Print VX2 Leitfaden
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 1 of 7
Purpose
This document provides guidance for maintaining the Sci-Print VX2/VXL and SOLO. If
the print head and rollers are not cleaned, adhesive residue build up from the labels can
cause a wide range of problems, including misalignment of text on the label, errors in
printing/applying labels, and improper tube handling in the roller assembly. This is a
supplemental guide to the User Manual for your instrument.
Required Material and Equipment
● Alcohol wipes or
alcohol and lint-free cloth (ex. KimWipe™)
● 4mm Allen Wrench
● 2.5mm Allen Wrench
Intended Audience
Scinomix End users
Procedure
Daily Maintenance (When in Use)
1. Remove any dropped tubes or labels.
a. Turn off internal air pressure with blue air shut off switch.
b. Unlock the roller assembly by pushing in on the black knob in FIgure 1.
and rotating 90 degrees until the word “RUN” is facing the front of the
instrument.
c. Pull the roller assembly out of the left side of the instrument.
Figure 1.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 2 of 7
d. Look inside the roller assembly for any tubes.
Figure 2.
2. Deck plate - Clean the deck after each run with a water-dampened lint-free cloth
(mild detergent can be used if necessary).
3. Red roller and clamp roller - Remove with a 4mm Allen wrench, clean with
alcohol wipe, and replace the red roller and clamp roller.
Note: Ensure the two steel rollers of the clamp roller are centered on the red
roller when reinstalling.
Figure 3.
4. Check the label stock and ribbon to ensure there’s enough for the next run.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 3 of 7
5. Power down the instrument (optional).
Periodic Maintenance (When changing Labels/Ribbon)
1. Clean the following with alcohol wipes.
a. Label tensioner rollers - Clean both pinching rollers with alcohol wipe,
dry with lint-free cloth. (A2+ model printer label tensioner is mounted in a
different position, but functions the same way).
Figure 4.
b. Label gap sensor - Look for any stuck labels, then floss with alcohol
wipe. (Wipe should not be too wet with alcohol). (A2+ model printer label
gap sensor is in the same position, but looks slightly different. Clean the
same way)
Figure 5.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 4 of 7
c. Print Drive Roller - Remove to clean with alcohol wipe. Dry with lint-free
cloth and reinstall. (A2+ model printer rollers are removed by removing
the entire black cap holding them in)
Note: Print Drive Roller has exposed metal at top, where Rewind Assist
Roller does not.
Figure 6.
d. Print head surface - Use one finger, wipe up with alcohol wipe.
Note: DO NOT SCRUB. Scrubbing can damage the print head.
Figure 7.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 5 of 7
e. Peel plate assembly - Removing the peel plate assembly should only be
done if the rollers have labels/adhesive on them, otherwise cleaning the
peel edge with an alcohol wipe can be done while the peel plate assembly
is still mounted on the printer.
If cleaning the rollers - disconnect peel blow tubing, loosen mounting
screw and pull peel plate assembly off the instrument for cleaning. Make
sure the 4 nozzles of the peel blow bar are pointing at the tip of the peel
edge (adjust if necessary using the screw on the top of the peel blow bar).
Note: When remounting the peel plate assembly, make sure the right
edge of the peel plate aligns with the boss. Failing to do so can cause
labels to drift up/down in the print head.
Figure 8. Some peel plate designs have less rollers. Please contact [email protected] if you
would like this updated design.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 6 of 7
f. Rewind Assist Roller (Cleaning this roller is optional) - Remove to
clean with alcohol wipe. Dry with lint-free cloth and reinstall. (A2+ model
printer rollers are removed by removing the entire black cap holding them
in)
Figure 9.
g. Roller clamp - Clean with alcohol wipes (Not necessary to remove).(A2+
model printer roller clamp looks slightly different. Clean the same way).
Figure 10.
2. Dust the surface of the printer and the inside surfaces of the instrument.
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
TS-1022
Required Printer
and Roller
Assembly
Maintenance
Document Owner:
Service Department
Effective Date:
APR-24-2020
Page 7 of 7
If you need additional assistance, please call our service department at
314-298-9800 or email
.
Definitions
N/A
Revision History
Version
Change
Effective Date
Approved by:
A
New
APR-24-2020
B. Petti
File Location: DMS Revision A Approved Date: APR-24-2020 Approved by: BP
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Scinomix Drucker Handbücher
