scope ActiveCore Bedienungsanleitung
RefrigerationRefrigeration
Freezer
User Guide – ActiveCore Freezer
Thank you for purchasing a SKOPE refrigeration product.
Safety
Always observe safety precautions when using any electrical appliance. Read these instructions carefully and retain them
for future reference.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Do not use this appliance for other than its intended use.
• Do not insert fingers/foreign objects into any holes.
• Only use this appliance with the voltage specified on the cabinet rating label.
• Ensure the appliance has adequate ventilation as this is essential to economical, high performance.
• Be careful not to touch moving parts and hot surfaces.
• For your own safety and that of others, ensure that all electrical work is done by authorised personnel.
• If the power supply flexible cord becomes damaged, it must be replaced by an authorised service agent or similarly qualified
person in order to avoid a hazard.
• Ensure all necessary safety precautions are observed during installation or removal of the refrigeration unit.
• The appliance is not designed to be stable while in motion. Use extreme caution when moving or transporting it.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• If the cabinet is to be scrapped, ensure the cabinet is unplugged from the power supply and cut off the mains flex close to the
back of the cabinet. Be mindful of the risk of animals or children becoming trapped in the appliance - either remove or secure
drawers if necessary.
• Refrigerant must be removed by a qualified service person and the cabinet recycled/disposed of in accordance with local
regulations.
Service & Support
We know you will get years of satisfaction from your new SKOPE product when you follow a few simple preventative
maintenance guidelines. Helpful information is available on the SKOPE website.
www.skope.com/serviceandsupport
WARNING
• Ensure the appliance is disconnected from the power supply before performing any cleaning or maintenance.
• Do not cover the grilles or block the entry or exhaust of airflow by placing objects up against the refrigeration unit.
• Should manual defrosting be necessary, turn off the refrigeration system and allow the ice to melt by air
circulation. Do not use mechanical methods to remove ice, as this may damage the refrigeration circuit.
• Do not use any electrical devices or appliances inside the food storage compartment.
WARNING
•
Ensure the doors are held shut when moving or transporting the freezer.
This cabinet is designed to operate within a specific climatic class environment.
See the cabinet rating label inside the cabinet for climate class number.
The cabinet includes relevant hazard symbols that may be associated with the
freezer. Refer to the information below for symbol description.
Climate class Ambient temperature Relative humidity WARNING
The refrigeration system contains flammable R290 refrigerant.
Do not tamper with it.
The refrigeration system must only be serviced by qualified
personnel.
3 25°C 60%
4 30°C 55%
5 40°C 40%
7 (tropical) 35°C 75%
RefrigerationRefrigeration
Freezer
Installation Guidelines
When installing this freezer, ensure the installation guidelines below are considered and met .
Ventilation Requirements
This freezer must have the following ventilation clearances at all times.
In certain climatic conditions, condensation may
form on the back of the cabinet. If this is observed, ensure air circulation between cabinet and wall by adhering two of the
enclosed self-adhesive blocks to the cabinet back as shown.
Ventilation
Ensure all ventilation
requirements below are
met.
Door Opening
Allow adequate space for
the door/s to open and
close properly.
Sunlight
Do not install the freezer
in direct sunlight.
Uneven Surface
Do not install the freezer
on an uneven surface.
Surface
The installation surface
must be capable of
supporting the loaded
cabinet.
Power Supply
Do not overload the power
supply.
Blocking Ventilation
Do not store boxes or items in
front or on top of the freezer.
Climate Class
The freezer must be
installed in an environment
within its climate class.*
The climate class is stated
on the cabinet rating label
inside the freezer, and
specified on the back page
of this user guide.
No below clearance required
Min. 300 mm above*
No behind
clearance
required
Vented top sign*
Min. 300 mm above*
No side
clearance
required
Rear top sign*
50mm
Adhesive Blocks
If required use two adhesive blocks on the rear of the cabinet. Position
the blocks on the left and right hand sides of the cabinet, approximately
in the centre and 50 mm from the cabinet edge.
RefrigerationRefrigeration
Freezer
Door Handles
The door handles may be packed inside the freezer.
Shelves
The wire shelves sit on shelf clips. The shelf clips twist onto the shelf support strips in the cabinet interior. The shelves
may be positioned at different heights to suit various product. Use the numbers on the shelf support strips to assist with
setting the shelf clips at the same height.
Loading product
Let the freezer run for 30 minutes before loading it with product for the first time. When loading the shelves with
product:
To fit a door handle To remove a door handle
1. A metal spring is fitted inside the
handle mounts. Ensure the springs
point up.
1. Peel back the door gasket from
behind the handle mounts on the
inside of the door frame.
2. Unscrew the handle mounts through
the holes on the inside of the door
frame, and remove the handle.
3. Only unscrew the top and bottom
screws. Do NOT unscrew the middle
screw.
3. Place BOTH handle mounts
simultaneously onto both door
brackets. Then push the handle
down onto the brackets until the
handle locks in place.
4. Remove the bracket/s from the
handle mount by pressing the
bracket in and down until it unclips
from the handle mount.
4. If the handle doesn’t lock into place,
check that the spring clips are
pointing up and try again. If only one
end of the handle locks into place,
remove the door handle and refit
with both handle mounts located
onto the brackets.
5. Fit and screw the bracket/s back
onto the door. Ensure the catches
are pointing up as pictured.
6. Clip the gasket back into place on
the inside of the door frame. If the
gasket is out of shape, use a hair
drier to heat and reshape it.
To fit a shelf clip:
Twist anticlockwise onto
the shelf support strip.
To remove a shelf clip:
Pull the centre tab up and
twist off clockwise.
To adjust the shelf clip
height:
Pull the centre tab up and
slide up or down as
required. Once in position,
ensure it clicks into place.
Handle
Bracket
Front of
door
Bracket
Bracket
Handle mount
Handle
Bracket
Catch
Catch
Spring clip
(pointing up)
Shelf Loading
Do not overload the
shelves.
Shelf Flexing
Remove product if the
shelf is flexing.
Shelf Overhang
Do not let product
overhang the shelves.
Front
Top
Back
MAX
46kg
per shelf
Internal Airflow
Leave 25 mm space
between product and
the back of cabinet
interior
Cabinet Floor
Do not load product
on the cabinet floor.
Use the shelves.
Load Limit
Do not load product
above the load limit
indicators on the
cabinet interior sides.
LOAD LIMIT
Door Lock/s
The freezer may be fitted with bracket locks or key locks, located above or below each door. Bracket locks require a lock
(padlock or similar) through the brackets to lock the door. Key locks can be locked with the supplied key.
Electronic Controller
The electronic controller regulates the freezer’s temperature, signals alarms and captures operational
information. The freezer temperature is factory set for storage of perishable product (all shelves maintain
L1 temperature range: less than -18°C (can spike up to -15°C
).
To customise the freezer settings to your requirements and view historical data, download the
SKOPE-connect app from the Google Play Store or Apple App Store, and connect via Bluetooth ®.
Lights
The freezer lights switch on and off automatically depending on freezer use.
Cleaning
Ensure the freezer is unplugged from the power supply before cleaning.
Wipe the inside and outside of the cabinet with a damp cloth, taking care to keep moisture away from electrical parts.
The condenser coil must be kept clean. SKOPE strongly urges cleaning the condenser coil every three months.
Do NOT use hard or sharp tools to clean the coil as these may cause damage.
Clean the Coil
1. Unplug the freezer from the power supply, and unplug any lit sign panels.
2. Remove the front panel from the top of the
cabinet.
WARNING: Front panel is heavy, a two person lift is
recommended.
3. Brush the condenser coil with a soft brush to
remove any dust and fluff.
4. Refit the sign assembly and reconnect to the
power supply.
Important
When refitting, ensure the tabs on the back of the
sign are located in the notches on top of the cabinet,
and that the sign is pushed fully in and secure.
Coil
Tab and notch
PRN80226 Rev. 1.0 Apr. 2022
RefrigerationRefrigeration
Freezer
Andere scope Gefrierschrank Handbücher
