Scott TX32 Bedienungsanleitung
LCD TV TX32
To our customers
LCD (Liquid Crystal Display) screens, like plasma and conventional CRT
(Cathode Ray Tube) screens, are also susceptible to ‘screen burn-in’ or
‘image retention’ which can be found on the screen as visible fixed lines and
shades and can’t be removed. To avoid such permanent damage to the
screen, it is advisable to take the following preventive actions:
(1) Avoid displaying still (inactive) images for more than two hours.
(2) Change the screen image aspect ratio from time to time.
(3) If it is necessary to display still images for a long time, lower the contranst
and brightness.
(4) Turn on the DPMS function (if available) when displaying PC input image.
Thank you for your attention and we hope you enjoy your new TV.
The apparatus shall not be exposed to dripping or splashing
and that no objects filled with liquids, such as vases, shall be placed on the apparatus
Apparatus with class 1 construction shall be connected to a mains socket outlet with a
protective earthing connection.
Warning-------------------------------------------------------------------------------------------2
Safety Instructions------------------------------------------------------------------------------3-4
Introduction--------------------------------------------------------------------------------------- 5
Connection Operations------------------------------------------------------------------------- 6-10
Remote Control----------------------------------------------------------------------------------- 11-12
Signal Mode---------------------------------------------------------------------------------------- 14
Specifications---------------------------------------------------------------------------------------13
TControl board specification-------------------------------------------------------------------- 15
Function Keys/Receiver PCB------------------------------------------------------------------- 16
Main board SCH------------------------------------------------------------------------------------ 17-25
Main board PCB------------------------------------------------------------------------------------ 26-29
Power Supply board SCH------------------------------------------------------------------------- 30
Power Supply board PCB------------------------------------------------------------------------ 31-36
Power Supply board Specification------------------------------------------------------------- 37-43
Control board Specification---------------------------------------------------------------------- 44-51
Factory menu--------------------------------------------------------------------------------------- 52-53
MSTAR upgrade and debugging--------------------------------------------------------------- 54-66
Warning
Warning
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated”dangerous voltage”within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance(servicing)instructions in the literature accompanying the ap-
pliance.
REGULATORY INFORMATION
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communica-
tion. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be de-
termined by turning the equipment off and on, the user encouraged to try to correct the interfere-
nce by one or more of the following measures:
- Relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
- Consult the dealer or experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CAUTION:
DO not attempt to modify this product in any way without written authorization from supplier. Unauthorized
modification could void the user’s authority to operate this product.
2
O w ner'sM anual
Safety instructions
Safety instructions
Safety instructions
WARNING :
WARNING :
TO Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat source such as radiators,
heat registers, stoves, or other apparatus(including
amplifiers)that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than other. A grounding type plug has
two blades and a third grounding prong. The wide bl-
ade or the third prong is provided for your safety.
When the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsole-
te outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience rece-
ptacles, and the point where they exit from the
apparatus.
11. Only use the attachments / accessories specified by
the manufacturer.
3
Safety instructions
Safety instructions continued
Safety instructions continued
12. Use only cart, stand, tripod, bracket, or table specified
by the manufacturer or sold with the apparatus.
13. Unplug this apparatus during lightning storms or when
unused for a long time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way.
Note
- If the TV is cold, there may be a small “flicker” when you turn it on.
- Avoid touching the LCD screen or holding your finger(s) against it.
CAUTION connecting the Power Cord
CAUTION connecting the Power Cord
Do not overload wall outlets. Overloaded wall outlets could damage the TV and could result to electric shock or fire.
Periodically examine the cord of your appliance; if its appearance indicates damage or deterioration, unplug it. Stop
using it until you have it replaced with a cord authorized by your dealer. Protect the power cord from physical
or mechanical abuse, such as being twisted, kinked or pinched.
On Disposal
On Disposal
- The fluorescent lamp used in this product contains a small amount of mercury
- Disposal of this product must be carried out in accordance to the regulations of your local authority.
4
5
Introduction
Introduction
Connection Options
6
SCART2SCART1
RF IN
NOITPIRCSEDNOITCNUFEMANKCAJMETI
CVBS INPUT
S-VIDEO INPUT C
EA5PHONE Connect the HDUphone
onnect the S-VIDEO output jack of DVD or VCR
PC-RGB INPUT Connect the PC-RGB output jack of PC
PC AUDIO INPUT Connectthe AudiooutputjackofPC
Connect the SCART jack of VCR
SCART
YPbPr IN
Connect the Video output jack of DVD or VCR
Connect the YPbPr output jack of DVD or VCR
TV SIGNAL IN Connect the antenna
HDMI INPUT
AC IN
Switch of the power supply
AC input socket
MAIN POWER BUTTON
Connect the HDMI output jack of PC and DVD
Connect the R/L Audio output jack of DVD or VCR for CVBS/YPbPr/S-VIDEO
CVBS/YPbPr/S-VIDEO
AUDIO INPUT
13 CI SLOT CI Slot for Common Interface
13
Introduction
External Equipment Connections
Power Cord Connection
- Connect the power cord correctly as shown.
Antenna Connection
- Press the POWER switch of your LCD TV to switch on the LCD TV. The power indicator on the front panel lights up in
Red
7
NOTE: Before connecting any external equipment, turn off all main power for safety.
- Antenna or Cable Service without a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
$QWHQQD
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna Socket
RF Coaxial Wire(75ohm)
VHF Antenna
UHF Antenna
Outdoor Antenna
Single-family Dwellings/Houses
(Connect to wall jack for outdoor antenna)
Bronze Wire
Be careful not to bend the bronze wire
when connecting the antenna.
In a poor signal area to improve picture quality,
purchase and install a signal amplifier.
If the antenna needs to be split for two TV’ s,
install a “2-Way signal splitter” in the connections.
If the antenna is not installed properly, Contact
your dealer for assistance .
VHF UHF
Signal
Amplifier
Introduction
AV/S-VIDEO INPUT Connection
NOTE: All cables shown are not included with the TV.
- Match the jacks colors: Video=yellow, Audio left=white,
and Audio right=red.
- Select the AV input source with using the TV/AV button
on the remote control.
- Connect the VIDEO and AUDIO output jack of the DVD or
VCR to the AV IN jacks on the set using the RCA cable.
Scart Connection
NOTE: All cables shown are not included with the TV.
1. Connect the scart connector on the external video device
to the scart connector 1 or 2 on the LCD TV using a scart
cable.
- SCART 1 connector supports full scart functions ( CVBS,
RGB input / output, TV out ).
- SCART 2 connector supports Y /C input and TV output.
2. Press AV / TV button on the remote control to select SC-
ART 1 or SCART 2 which corresponds with your connec-
tion.
Input / Output specification
Connector
SCART
Input Output
Y / C RGB AUDIO(L/R) CVBS TV AUDIO(L/R)
8
DVD or VCR
DVD Back
RCA Audio Cable
RCA Video Cable
TV Back
DVD or VCR
Scart cable
DVD or VCR Back
TV Back
- Select the S-VIDEO input source with using the TV/AV
button on the remote control.
- Connect the S-VIDEO and AUDIO output jack of the DVD
or VCR to the S-VIDEO IN and AUDIO IN jacks on the set.
Do not connect both VIDEO and S-VIDEO
at the same time.
S-VIDEO OUT
Inhaltsverzeichnis
Andere Scott LCD-Fernseher Handbücher
