Scotts LSS10172S Bedienungsanleitung

Model LSS10172S

OWNER’S MANUAL

Cordless 7.2 Volt Lithium Shrub Shear

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

CA Compliant Charger Included (Model No. HYCH0900400U)

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS,

SERVICE QUESTIONS? GO TO SCOTTS.AMERICANLAWNMOWER.COM OR CALL

1-800-618-7474 BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.

Thank you for your purchase.

BATTERY MUST BE

CHARGED BEFORE FIRST

USE. TWO TO THREE INITIAL

CHARGING/DISCHARGING

CYCLES MAY BE REQUIRED

TO ACHIEVE MAXIMUM RUN

TIME/CAPACITY.

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

WARNING: Personal Injury and Damage! Keep

your hands and feet away from the cutting tool,

especially when the products are switched on!

Never adjust the cutting head when the product is

in the “on” position. Do not touch moving blades.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances, basic

safety precautions should always be followed to

reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

AVOID DANGEROUS ENVIRONMENTS - Do

not use this product in the rain or in damp or wet

conditions. Do not operate in gaseous or explosive

atmospheres. Motors in these products normally

spark, and the sparks might ignite fumes.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Use of rubber gloves and protective footwear is

recommended when working outdoors.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product. Use face or dust mask if environment

is dusty.

DANGER: Risk of cut. Keep hands away from

blades.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

WARNING: Switch off before adjusting or cleaning.

CAUTION: The blades continue to move for a few

seconds after the tool is switched off.

AVOID UNINTENTIONAL STARTING - Do not carry

this product with finger on switch.

IMPORTANT! Any use which is not expressly

permitted in the manual may result in damage to

the tool and place the use in serious danger.

Please carefully read the restrictions in the

operating instructions.

IMPORTANT! Before each use check for damaged

or worn parts. Check for alignment of moving parts,

binding of moving parts, breakage, mounting and

any other condition that may affect its operation.

Any part that is damaged should be properly

repaired or replaced. For assistance call our

customer service help line at 1-800-618-7474.

STORE INDOORS-When not in use, this product

should be stored indoors in a dry location out of

reach of children.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate this product

when you are tired or under the influence of drugs,

alcohol or medications.

DANGER: If blade jams on any electrical cord

or line, DO NOT TOUCH THE BLADE! IT CAN

BECOME ELECTRICALLY LIVE AND VERY

DANGEROUS. Release the unit in the safest

manner possible. Disconnect the damaged

electrical cord or line from the power source. If

possible, do so safely, if in doubt, call an electrician

or the electrical contractor for assistance. Failure to

heed this Danger can result in serious personal

injury and possible death.

LIGHTING - Only operate this tool in daylight or

good artificial light.

DON’T OVERREACH - Keep proper footing and

balance at all times.

DANGER: Make sure trigger switch is off and

safety button is not pushed when clearing jammed

material from blades.

MAINTAIN TOOL WITH CARE-Keep blades sharp

and clean for best performance and to reduce the

risk of injury. Keep handle dry, clean and free from

oil and grease.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

Model LSS10172S

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Always wear eye protection.

Do not use in rain or electrical storms.

WARNING! Wear protective gloves!

WARNING! Keep bystanders away.

WARNING! Wear safety footwear!

CAUTION! Wear ear protection!

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

EXPLANATION OF SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

CHARGING THE BATTERY

 The battery must be fully charged before using

for the first time. The charging time is 3 to 5

hours. (See page 5 for instructions.)

 The battery charger supplied matches the

lithium battery installed in the tool. DO NOT

use any other charger to recharge the tool.

 To protect the lithium battery against deep

discharging, when the battery is flat, the tool

will automatically switch off via a protective

circuit.

If the On/Off switch is used continually at this point,

the lithium battery can be damaged. Do not try to

continue to use the tool before recharging the

battery.

GENERAL SAFETY

FCC Warnings:

Please note that changes or modifications to this

product not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and

receiver.

-- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV

technician for help.

Model LSS10172S

PRODUCT SPECIFICATIONS

Model: LSS10172S

Input: 7.2V DC, 2.0 Ah -Lithium-ion battery

Battery capacity: 2000mAH -3.54inch (90mm) grass shear blade width

No load speed: 2600 SPM -6,69inch (170mm) shrub trimming blade cutting length

Charger (adaptor) input:100-120V, 50/60Hz AC -5/16 inch (8mm) shrub trimming blade max. cutting diameter

Battery charging time: 3 - 5 hours -Tool-less blade changing system

PARTS LIST

1 Grass cutter blade

2 Blade release button

3 Safety lock button

4 On/Off trigger switch

5 Shrub trimming blade

6 Blade guards

8 Rotating angle button

7 Battery charger

Model LSS10172S

GENERAL INSTRUCTIONS

PACKING LIST

- Shear with Grass Cutter Blade Assembled

- Shrub Trimming Blade

- Blade Guards

- Battery Charger

- Owner’s Manual

UNPACKING

Carefully remove the product from the box. Make

sure that all items listed in the packing list are

included.

Inspect all items carefully to make sure no breakage

or damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

tool.

WARNING: If any parts are damaged or missing

please do not operate this product until the parts are

replaced. Failure to heed this warning could result

in serious personal injury. Call our customer service

help line at 1-800-618-7474 for assistance.

CHARGING PROCEDURE

1. Insert the charger cable into the charging inlet

on the tool.

2. Make sure the wall outlet in your home is normal

household voltage (AC120V, 60 Hz). Insert the

battery charger plug into the wall outlet.

3. The red LED (A) charging indicator lights up to

tell you that the battery pack is on charge. The

battery is fully charged when the red LED

charging indicator is no longer lit.

 During the charging process, it is normal for

the handle of the tool to warm up.

 When not using the tool for extended periods,

disconnect the battery charger from the socket.

 When the trimming shears are charging, you

must not use them.

 Only charge the battery between 0°-37.8°C

(32°-100°F).

 After prolonged use, allow the battery to cool

down before recharging.

STARTING AND STOPPING

Starting:

1. Push the safety lock button and press the

on/off trigger switch at the same time.

2. Release the safety lock button.

Stopping:

1. Release the on/off trigger switch.

OPERATING INSTRUCTIONS

This product is intended for light trimming of

shrubs, hedges and lawn edges. Please note that

this tool is not designed for commercial, trade,

or industrial use. Only use this product for the

purpose specified in these instructions. Any other

use will void the warranty.

GRASS CUTTER BLADE

Use the grass cutter blade for cutting the edges of

lawns and small areas of grass in private gardens

and hobby areas.

The grass cutter blade is not intended for cutting

hedges of chopping material up for composting.

Edging

Guide the tool along the edge of the lawn.

After use install the blade guard.

Tips:

Do not force the unit through dense growth, and

if the blades slow down, reduce your speed.

Avoid trimming too close to dirt, sand or gravel,

as this could dull the blades and reduce the

cutting efficiency.

Do not allow the blade to contact paved surfaces,

stones or garden walls, as this will rapidly wear

down the blade.

SHRUB TRIMMING BLADE

Use the shrub trimming blade for trimming and

shaping individual bushes, shrubs, and climbing

plants in private domestic and hobby gardens.

The shrub trimming blade is not intended for cutting

grass / edging.

Cutting shrubs

 Before using, check the shrubs for foreign

objects e.g. wire, etc.

 When using the tool hold it away from yourself

and stand in a secure position with your weight

evenly balanced on both feet.

 When cutting, move steadily along the line of

cut, so that stems are fed directly into the cutter

blades.

 After use, install the blade guard.

Model LSS10172S

GENERAL INSTRUCTIONS

Recommended cutting/trimming times:

Cut hedges with deciduous leaves in June

and October.

Cut evergreen hedges in April and August.

Cut conifer and other fast growing shrubs

approximately every six weeks from May

through October.

CHANGING BLADES

CAUTION: Blades can cause injury. Wear gloves

when changing blades.

CAUTION: Do not press the safety lock button of

the shear during blade changes.

Removing the blades:

1. Press the blade release button (A) and slide the

blade downward to remove as shown. (Fig.1)

2. Once you have removed the blade you will be able

to see the toothed wheels of the gear unit

(Fig. 2). Make sure that no dirt gets into the gear

unit when you change the blade.

To assemble, proceed in the reverse order.

Adjusting the handle angles:

To push inside the

rotating angle button

then rotate the

machine handle. (Fig.

There are 3 positions

（-30 ° to +30 °）

engraved on housing.

After you choose the position that you want, then

release the rotating angle button.

Model LSS10172S

Fig. 1

Fig. 2

Gear

Fig. 3

MAINTENANCE / CLEANING / STORAGE

MAINTENANCE:

CAUTION: Blades can cause injury. Do not press

the safety lock of the shear during maintenance

work.

Note: To ensure long and reliable service, regularly

carry out the following maintenance:

 Check for obvious defects such as a damaged

or loose blade, housing, or components.

 If the tool should stop working properly, repair

should be carried out by a qualified individual,

using identical replacement parts.

CAUTION: Never clean the trimming shears in

water (especially running water), as there is a risk

of personal injury and damage to the shears.

To obtain good cutting results, always make sure

the blades are sharp, and clean them from time to

time with a soft dry cloth.

For easier operation and longer blade life, use light

machine oil to lubricate the trimming and grass

shear blades before and after each use.

Check the condition of the cutting edges of the

blades, and always immediately remove notches

and burrs caused by stones, etc.

There are no parts inside the equipment which

require additional maintenance.

CLEANING / STORAGE

 Clean the exterior of the tool thoroughly

using a soft brush and cloth. Do not use water,

solvents, or polishes.

 Remove all debris from the tool.

 After use, cover the blades with the guards

provided.

 Charge the battery 3 to 5 hours before storing.

 If the tool is to be stored for an extended period

of time or during winter storage, charge the

battery at least once every there months to

protect it from damage.

 Store the tool in a dry secure place out of reach

of children.

 Do not place any other objects on top of the

tool.

 This tool must not be stored in temperatures

over 40°C (104°F) or under direct exposure to

sunlight.

 Do not store the tool in places with static

electricity.

CALL US FIRST !!

Call us first with questions about operating or maintaining your product

at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on scotts.americanlawnmower.com.

PARTS AND SERVICE

Always mention the model number when ordering kits/items for this tool.

No. Kit/Item Number Description QTY

1 LSS-GSA Grass shear blade assy

kit

2 LSS-HTA Shrub shear blade assy

kit

3 LSS-PR-CHK Charger 1

For parts or service, please call 1-800-618-7474 or visit us online at

scotts.americanlawnmower.com. Be sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model/ serial number of this tool is found on a plate or label attached to the housing. Please

record the serial number in the space provided below.

MODEL NUMBER LSS10172S _

SERIAL NUMBER_______________

Model LSS10172S

BATTERY DISPOSAL

The RBRC indicates that the costs to recycle the battery at the end of its useful life has already been paid by The Great States Corporation

American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal solid waste or in the trash. RBRC in

cooperation with The Great States Corporation American Lawn Mower Company has provided an environmentally friendly and easy way to

recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY for information on where to drop off the spent

battery.

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OWNER’S MANUAL

LSS10172S Cordless 7.2V Lithium Shrub Shear

Rev. 11/26/2018

WARRANTY POLICY

Scotts Warranty policy

 2 Year limited warranty on all Scotts electric hand tools from date of purchase when used for personal, household, or family use.

The Great States Corp. (GSC) warrants to the original owner that this Scotts product and service part is free from defects in materials

and workmanship and agrees to repair or replace any defective product or part for the warranty period as stated above.

 Warranty voided if used for commercial or industrial purposes or any other improper use as determined by GSC.

 Warranty does not include repairs necessary due to operator’s abuse or negligence (including overloading the product beyond

capacity or immersion in water), or the failure to assemble, operate, maintain or store the product according to the instructions in

the owner’s manual.

 This warranty does not cover

 Wear items, including but not limited to - drive belts & gears, tines, cutting blades, mower blades, saw chains, mulching

blades, blower fans, spool covers, trimmer line, blower and vacuum tubes, guide bars, high pressure hoses, wheels,

handles, augers, worn bags, power cables, and other items subject to wear over time.

 Wear on batteries, including but not limited to – drops, wear and breakage on charger, exposure to extreme temperature

swings (hot or cold), battery left on charger too long, battery left uncharged for too long, and misuse or abuse of the

battery.

 This warranty does not cover damage caused by cold, heat, rain, excessive humidity or other environmental extremes.

 This warranty does not cover normal deterioration of the exterior finish or normal wear and tear on the products including, but not

limited to scratches, cracks, dents, or damage caused by outside chemicals.

 This warranty is not transferable and only applies to new products sold directly from an authorized retailer. This warranty does not

apply to any product, new or used, purchased through unauthorized third-party channels. For information on authorized dealers,

contact our customer support hotline at 1-800-618-7474 (Mon-Fri 8am-5pm Est)

 Any incidental, indirect or consequential loss, damage, or expense that may result from any defect or malfunction of the products is

not covered by the warranty.

 The warranty does not include installation, assembly or normal adjustments explained in the operator’s manual. The expense of

delivering the product to the vendor and the expense of returning the product or replacement parts to the owner is not covered by

the warranty.

Additional Warranty Limitations

Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

Products sold damaged or incomplete, sold ―as is, or sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper handling, improper assembly, incorrect voltage, improper wiring, improper

maintenance, improper modification or the use of accessories and/or attachments not specifically recommended is not covered by this

warranty.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

For claims go to scotts.americanlawnmower.com or call our customer support hotline from 8am-5pm EST, Mon-Fri at

1-800-618-7474

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

Indianapolis, IN 46256 USA

Phone 1-800-618-7474

scotts.americanlawnmower.com

Modelo LSS10172S

MANUAL DEL OPERARIO

Cizalla de litio sin cable de 7.2 voltios

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE

FUNCIONAMIENTO, MONTAJE, PIEZAS O SERVICIO TÉCNICO? IR A

SCOTTS.AMERICANLAWNMOWER.COM O LLAME AL 1-800-618-7474 ENTRE LAS

8:00 AM Y LAS 5:00 PM, HORA DEL ESTE DE LOS ESTADOS UNIDOS.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y

seguridad para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el

manual del operario antes de usar este producto.

Cargador Cumple con CA está incluido (Modelo No. HYCH0900400U)

DEBE CARGAR LA BATERÍA

ANTES DE UTILIZARLA POR

PRIMERA VEZ. ES POSIBLE QUE

SE NECESITEN DE DOS A TRES

CICLOS DE CARGA/ DESCARGA

INICIALES PARA OBTENER LA

MÁXIMA CAPACIDAD O TIEMPO DE

FUNCIONAMIENTO.

Guarde estas instrucciones y revíselas con

frecuencia antes de usar la herramienta y para

impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos,

se recomienda respetar siempre las precauciones

de seguridad básicas que se detallan a continuación,

a fin de reducir riesgos de incendios, descargas

eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

EVITE AMBIENTES PELIGROSOS. No utilice este

producto en condiciones de lluvia o tormenta.

Tampoco trabaje en entornos donde existan gases o

sustancias explosivas. Por lo general, los motores de

estos productos producen chispas que podrían

inflamar los gases.

USE ROPA ADECUADA. No use prendas sueltas

ni artículos de joyería mientras trabaja con este

producto. Use protección para cubrir y sujetar el

cabello largo, ya que puede quedar atrapado en las

piezas móviles. Se recomienda usar guantes de goma

y calzado de protección cuando se trabaja al aire libre.

USE GAFAS DE SEGURIDAD. Al trabajar con este

producto, use gafas de seguridad con protectores

laterales que cumplan con la norma ANSI Z87.1.

Protéjase la cara con una mascarilla antipolvo si hay

polvo en el ambiente.

PELIGRO: Riesgo de corte. Mantenga las manos

alejadas de las cushillas.

USE LA HERRAMIENTA CORRECTA. No utilice este

herramienta n trabajos para los que no esté indicada.

ADVERTENCIA: Apague la unidad antes de limpiaria

o de realizer ajustes.

PRECAUCIÓN: Las cuchillas se siguen moviendo

durante algunos segundos después de apagar la

herramienta.

EVITE EL ENCENDIDO ACCIDENTAL. No transporte

el producto con el dedo en el interruptor.

¡IMPORTANTE! Cualquier uso que no esté permitido

en forma expresa en el manual puede provocar daños

a la herramienta y poner al usuario en grave peligro.

Lea detenidamente las restricciones que figuran en las

instrucciones de operación.

¡IMPORTANTE! Revise la herramienta antes de cada

uso para detectar si hay piezas gastadas o dañadas.

Verifique la alineación y las uniones de las piezas

móviles, el montaje, averías y otros factores que

puedan afectar el funcionamiento. Se debe reparar

o reemplazar cualquier pieza dañada, en forma

adecuada. Para recibir asistencia, comuníquese

con nuestra línea de ayuda de atención al cliente

al 1-800-618-7474.

GUARDE LA HERRAMIENTA BAJO TECHO.

Cuando no esté en uso, se deberá guardar en un

lugar cerrado y seco, fuera del alcance de los niños.

PONGA ATENCIÓN. Observe lo que está hacienda.

Use el sentido común. No opere este producto si

está cansado o bajo la influencia de drogas, alcohol

o medicamentos.

PELIGRO: Si la cuchilla se atasca en algún cable o

línea eléctrica, NO TOQUE LA CUCHILLA. PUEDE

ESTAR ELECTRIFICADA Y SER MUY

PELIGROSA. Suelte la unidad de la forma más

segura posible. Desconecte el cable o línea

eléctrica dañada del suministro eléctrico. Si es

posible, hágalo de una manera segura. Si tiene

dudas, llame a un electricista o al contratista

eléctrico para obtener ayuda. El no prestar atención

a este aviso de peligro puede causar lesiones

personales de gravedad y, posiblemente, la muerte.

ILUMINACIÓN. Trabaje con la sopladora de nieve

sólo con luz natural o buena luz artificial.

NO ADOPTE UNA POSTURA INCÓMODA.

Mantenga una base y equilibrio apropiados en todo

momento.

PELIGRO: Asegúrese de que el gatillo esté en

posición de apagado y el botón de seguridad no

esté presionado para luego retirar el material

atascado en las cuchillas.

TENGA CUIDADO AL REALIZAR EL

MANTENIMIENTO. Las cuchillas siempre deben

estar afiladas y limpias para lograr un óptimo

funcionamiento y reducer el riesgo de lesions.

Mantenga el mango seco, limpio y libre de grasa y

aceite.

MANTENER apartados a los niños - todos los

visitantes, niños y animales domésticos deben

permanecer a una distancia segura del área de

trabajo.

ADVERTENCIA: Proposición 65 de California:

Este producto contiene sustancias químicas al

estado de California como causantes de cáncer,

defectos de nacimiento u otros problemas

reproductivos .

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

NORMAS GENERALES DE SEGURIDAD

PARA REDUCIR EL RIESGO DE LESIONES: Antes

de utilizar este producto, cerciórese de que todos los

usuarios lean y comprendan las instrucciones

de seguridad y la demás información incluida en

este manual.

ADVERTENCIA: Daños y lesions personales. Aleje las

manos y los pies de la cortadora, especialmente

cuando el producto está encendido. Nunca ajuste el

cabezal de corte cuando el producto está en la

posición de encendido. No toque las cuchillas en

movimiento.

Modelo LSS10172S

Inhaltsverzeichnis

Sprachen:

Andere Scotts Elektrowerkzeuge Handbücher

Scotts

Scotts LSS10272PS Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung