Scout URC-21 Series Bedienungsanleitung

Scout URC-21XXX/23XXX Remote

The Scout remote is designed to operate all of the features of our cable box and the

most commonly used features from TVs: Volume Control, Mute, and Power. It's

preset to your cable converter and has preprogrammed technology for easy setup.

It's also guaranteed to operate all infrared remote controllable televisions

manufactured for the U.S. market.

The SETUP button is used to program Scout.

● The TV and CBL buttons are used to power on your TV and cable converter

respectively.

●

The VOL UP/DWN and MUTE buttons are used to control the volume of your

TV or cable converter.

●

The CH UP/DWN buttons are used to change the channels on your cable

converter.

●

The Number buttons (0 - 9) are used for directly accessing the channels on

your cable converter.

●

The LAST button returns you to the previously viewed channel on your cable

converter.

●

The FAV button accesses the favorite channels stored into your cable

converter. For instructions on setting up a Favorite Channel table, refer to

your cable converter manual.

●

The CABLE INTERACTIVE buttons, (at the bottom of the remote) control the

functions of your cable converter and will vary depending on the

manufacturer of your cable converter. Refer to your cable converter manual

for button descriptions.

●

Installing the Batteries

Setting Up Your Scout to Operate Your TV

Searching for Your Television Code

Getting Codes from Your Scout

Volume Lock

Troubleshooting

Installing the Batteries

The Scout requires four new AAA alkaline batteries.

On the back of the Scout, pull back on the tab and lift off the battery cover.1. Match the +and -marks on the batteries to the ones in the battery compartment of the remote.2. Press the battery cover back into place.3. Test the remote control by pressing the TV button. If the batteries are installed correctly, the red

light on the remote will blink once.

Setting Up Your Scout to Operate Your TV

Turn on your TV.1. Press and hold the SETUP button until the Scout's red light blinks twice. Release the SETUP

button.

Enter the first 3-digit setup code for your brand of television. If you entered the code correctly, the

Scout's red light will blink twice.

Aim the Scout at your television and press the TV button. Your television should turn off. If your

television does not turn off, repeat steps 1 - 3 trying each code for you brand of TV until you find the

code that operates your television.

Note: Since the Scout is only designed to operate Televisions and cable converters, the

Scout is not able to operate TV/VCR combinations.

Searching for Your Television Code

Turn on your television.1. Press and hold the SETUP button until the Scout's red light blinks twice. Release the SETUP

button.

Press the following buttons: 9, 9, and 1. The Scout's red light will blink twice3. Aim the Scout at your Television and slowly alternate between pressing the TV and MUTE buttons

until your television mutes (make sure the sound on your TV is turned up). You may have to press

this sequence of buttons up to 100 times to search the entire library of codes.

Once your television mutes, press and release the SETUP button to lock in your code. Your Scout is

ready to operate your television.

Getting Codes from Your Scout

If you need to find out which three-digit code is operating your television after your television is set up, use

this procedure:

Press and hold the SETUP button until the Scout's red light blinks twice, then release the SETUP

button.

Press the following buttons: 9, 9, and 0. The Scout's red light will blink twice.2. For the first digit if your three digit code, press the 1button, wait and count the number of times the

Scout's red light blinks. If the light does not blink when you press the 1button, the digit is zero.

For the second digit of your three digit code, press the 2button, wait and count the number of times

the Scout's red light blinks. If the light does not blink when you press the 2button, the digit is zero.

For the third digit of your three digit code, press the 3button, wait and count the number of times the

Scout's red light blinks. If the light does not blink when you press the 3button, the digit is zero.

Now you have the 3-digit code for your television.6.

Volume Lock

If your television is not remote controllable or, if you have a TV/VCR combination, you can access the

volume of your cable converter. To change the volume setting on the Scout, use the following:

Press and hold the SETUP button until Scout's red light blinks twice, then release the SETUP

button.

Press the following buttons: 9, 9, and 3. The Scout's red light will blink twice.2. Press and release the CBL button. The Scout's red light will blink twice.3. Now whenever you press the VOL UP/DWN buttons on Scout, your volume will be controlled by

your cable converter.

To return the volume to the TV:

Press and hold the SETUP button until Scout's red light blinks twice, then release the SETUP

button. Press the following buttons: 9, 9, and 3. The Scout's red light will blink twice.

Press and release the TV button. The Scout's red light will blink twice.2. Now, whenever you press the VOL UP/DWN buttons on the Scout, your volume will be controlled by

your television.

Troubleshooting

Problem Solution

Red light not blinking when you press a

button? Replace the batteries with 4 new AAA

batteries.