Screen Technics ELECTRICINEMA Bedienungsanleitung

ElectriCinema with IR Remote Control &

Installation Instructions

Thank you for purchasing a Screen Technics Projection Screen, please ensure that you

read the following instructions fully before attempting to install this product.

Before you Install Screen

Once you have unpacked the screen from the box, lay the canister on the ground and

carefully remove the black tape holding the screen surface in place – once the surface is

freed from the canister, take the bottom slat rod, which is taped to the canister, and insert it

into the bottom end corner of the screen until it is all the way inserted into the pocket, as

illustrated below. Then install the screen as described to follow.

Wall Mounting Instructions

1. Measure the wall where the screen is to be installed and mark with a pencil the

desired height to top of screen case and also the centre of the screen.

2. Measure the length of screen canister along the top surface and mark the centre

of the canister with a pencil, to assist in lining up the screen when mounting.

3. Determine the best positions for the wall brackets, allowing that in Gyprock or in

low strength walls the brackets will be screwed into a timber stud. In more solid

walls, such as masonry, position the brackets approx 150mm in from the canister

end. The brackets should be no more than 450mm in from each end. You must

use a minimum of 3 off wood screws per bracket or 2 off Dyna-bolts, for masonry

walls and you must be satisfied that the attachment is strong enough for the a

safe installation.

NB: Top of bracket

equals top of screen canister.

4. You may need to remove the bottom clip in order to screw brackets to wall,

please ensure to replace them afterwards.

5. Using two people install the screen by placing the screen canister into the bottom

of the bracket clips and pivoting back the canister to slot the top pins into the T

channels running along the top of the canister (you may have to remove any tape

that is in the way).

6. Holding screen in position tighten up Allen screw at each end and check that the

top pins have hooked into the T section of the screen canister.

7. See Page 5 electrical connection information.

Ceiling Mount Instructions

Below is a photo showing a side view using the brackets for ceiling fixing, you would

follow the instructions for the wall mounting system, with the only difference being

the screen is mounted hard against the ceiling. It is important that adequate support

is supplied by the ceiling structure to support the screen and to ensure a safe

installation. Never rely just on the Gyprock for attachment.

Please follow these instructions to ensure trouble free operation;

• Ensure that the screen is free to descend and that any adhesive tape that has been

placed on the bottom of the screen (to stop movement during transport) has been

removed.

• When installed, the opening in the canister should be down and at the back of the

canister. This will put the motor on the left-hand side of the screen, as viewed by the

audience.

• Cleaning of the screen is best achieved by first dusting the surface with a feather

duster, then to remove any stubborn marks, use a small amount of mild detergent

and warm water on a clean white lint free cloth. Do not use a saturated cloth, as this

may leave a watermark, only a damp one. It is most important that you only treat the

actual mark by this process and not the entire surface.

• The screen comes complete with a IR transmitter and 3-pin plug already attached to

the flex leaving the screen. After installation and turning the power on to the screen

the screen is ready to go, once you have placed and connected the IR Sensor unit

which plugs into the Data cable that exits the canister.

Please note: It adjust the up and down limit positions on ElectriCinema IR Projection

Screens you require an ILT Limit Setting Tool to make adjustments – see price list for

details.

 The Motor is 240 V 50Hz and draws 1.2 A.

 The screen drop is set and tested at the factory. Therefore, any damage caused to the

screen from limit re-adjustment is not covered by warranty.

Should you have any questions regarding the installation of our projection screens please

call our technical sales desk on 02 4869 2100 for assistance.

Cnr Vale & Suttor Roads

Moss Vale

NSW 2577

PH – 02 4869 2100

Fax – 02 4869 2123

Thinking Screens… Think Screen Technics

Andere Handbücher für ELECTRICINEMA

Inhaltsverzeichnis

Andere Screen Technics Projektionsfläche Handbücher

Screen Technics

Screen Technics CINEMASNAP 235 Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA Bedienungsanleitung

Screen Technics

Screen Technics CINEMATECH Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA 235 Leitfaden

Screen Technics

Screen Technics ELECTRICINEMA A Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA 235 Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA Bedienungsanleitung

Screen Technics

Screen Technics MASTERFIT IP Bedienungsanleitung

Screen Technics

Screen Technics ViewMaster Pro Bedienungsanleitung

Screen Technics

Screen Technics TRAPDOOR Bedienungsanleitung

Screen Technics

Screen Technics CINEMASNAP XL Bedienungsanleitung

Screen Technics

Screen Technics CINEMAPRO Bedienungsanleitung

Screen Technics

Screen Technics ELECTRICINEMA A Bedienungsanleitung

Screen Technics

Screen Technics CinemaSnap Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch