SCS TMTOOL Montage- und Bedienungsanleitung

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com

Verication Tester for WSMONITOR

Installation, Operation and Maintenance

January 2016

USER GUIDE TB-9048

Description

The SCS TMTOOL Verification Tester is designed to

simplify the process of calibrating SCS WSMONITOR

series Workstation Constant Monitors. The SCS

TMTOOL Verification Tester provides an efficient and

accurate means to perform ANSI/ESD S20.20 required

Compliance Verification per ESD TR53.

Frequency of recalibration should be based on the

critical nature of those ESD sensitive items handled and

the risk of failure for the ESD protective equipment and

materials. In general, SCS recommends that calibration

be performed annually.

Use the SCS TMTOOL Verification Tester to perform

compliance verification testing of the SCS WSMONITOR

series. It can be used at the workstation where the

monitors are installed, virtually eliminating downtime.

Testing takes a few minutes, verifying that the monitor is

operating within tolerances (adjustment is not possible).

The TMTOOL Verification Tester is to be used with the

following items:

WSMONITOR1

WSMONITOR1-230VAC

WSMONITOR2

WSMONITOR2-230VAC

WSMONITOR3

WSMONITOR3-230VAC

Packaging

1 Verication Tester

1 Certicate of Calibration

Operation

WSMONITOR1

1. Ground the TMTOOL Verification Tester by

connecting its GROUND lead to electrical ground.

2. Power the WSMONITOR1 monitor.

3. Insert the OPERATOR LEFT lead from the

Verification Tester into the OPER jack located on

the front of the WSMONITOR1 monitor.

Made in the

United States of America

Figure 1. SCS TMTOOL Verication Tester

Figure 2. Connecting the Verication Tester to the

WSMONITOR1 monitor

4. Press and hold the OPERATOR LEFT button on the

Verification Tester. The LED on the WSMONITOR1

should illuminate green. Release the button. The

LED should flash red, and the audible alarm should

sound briefly.

5. The monitor is within specifications if it responds as

described above.

WSMONITOR2

1. Ground the TMTOOL Verification Tester by

connecting its GROUND lead to eletrical ground.

2. Power the WSMONITOR2 monitor.

3. Insert the OPERATOR LEFT lead from the

Verification Tester into the operator jack located on

the front of the WSMONITOR2 monitor.

4. Insert the BENCH lead from the Verification Tester

into the BENCH SYSTEM GROUND jack located on

the back of the WSMONITOR2 monitor.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com

5. Press and hold the OPERATOR LEFT button on the

Verification Tester. The OPERATOR LED on the

WSMONITOR2 should illuminate green. Release

the button. The LED should flash red, and the

audible alarm should sound briefly.

6. Press and hold the BENCH button on the

Verification Tester. The BENCH LED on the

WSMONITOR2 should flash red, and the audible

alarm should sound. Release the button. The LED

should illuminate green red, and the audible alarm

should not sound.

7. The monitor is within specifications if it responds as

described in steps 5 and 6.

WSMONITOR3

1. Ground the TMTOOL Verification Tester by

connecting its GROUND lead to eletrical ground.

2. Power the WSMONITOR3 monitor.

3. Insert the OPERATOR LEFT lead from the

Verification Tester into the operator jack located on

the left remote of the WSMONITOR3 monitor.

4. Insert the OPERATOR RIGHT lead from the

Verification Tester into the operator jack located on

the right remote of the WSMONITOR3 monitor.

5. Insert the BENCH lead from the Verification Tester

into the BENCH SYSTEM GROUND jack located on

the back of the WSMONITOR3 monitor.

6. Press and hold the OPERATOR LEFT button on

the Verification Tester. The LEFT OPERATOR

LED on the WSMONITOR3 should illuminate green.

Release the button. The LED should flash red, and

the audible alarm should sound briefly.

7. Press and hold the OPERATOR RIGHT button on

the Verification Tester. The RIGHT OPERATOR

LED on the WSMONITOR3 should illuminate green.

Release the button. The LED should flash red, and

the audible alarm should sound briefly.

8. Press and hold the BENCH button on the

Verification Tester. The BENCH SYSTEM

GROUND LED on the WSMONITOR3 should flash

red, and the audible alarm should sound. Release

the button. The LED should illuminate green red,

and the audible alarm should not sound.

9. The monitor is within specifications if it responds as

described in steps 6-8.

Figure 4. Connecting the Verication Tester to the

WSMONITOR3 monitor

BACK

FRONT

Figure 3. Connecting the Verication Tester to the

WSMONITOR2 monitor

FRONT BACK

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332 • (919) 718-0000 • Website: StaticControl.com

Specifications

Dimensions:

2.4" L x 4.0" W x 1.0" H

(6.1 cm L x 10.2 cm W x 2.5 cm H)

Weight:

0.4 lbs

(0.2 kg)

Made in China

Limited Warranty, Warranty Exclusions, Limit of

Liability and RMA Request Instructions

See the SCS Warranty -

http://staticcontrol.descoindustries.com/warranty.aspx

Inhaltsverzeichnis

Andere SCS Prüfgeräte Handbücher

SCS

SCS WSMONITOR2 Plus Bedienungsanleitung

SCS

SCS 770030 Bedienungsanleitung

SCS

SCS 770065 Bedienungsanleitung

SCS

SCS TB-9029 Bedienungsanleitung

SCS

SCS TB-9031 Bedienungsanleitung

SCS

SCS 770716 Installationsanleitung

SCS

SCS 746 Bedienungsanleitung

SCS

SCS 770758 Montage- und Bedienungsanleitung

SCS

SCS 770734 Bedienungsanleitung

SCS

SCS 770065 Bedienungsanleitung

SCS

SCS 724VK2 Bedienungsanleitung

SCS

SCS 740 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung