SDC 631RF Bedienungsanleitung
P:\INSTALLATION INST\Power Supplies\INST-631RF_631RFA.vsd Rev C 01-12
REGULATED POWER SUPPLY
INSTALLATION INSTRUCTIONS
MODEL 631RF/631RFA
SECURITY DOOR CONTROLS
801 Avenida Acaso, Camarillo, Ca. 93012
(805) 494-0622 • Fax: (805) 494-8861
www.sdcsecurity.com • E-mail: service@sdcsecurity.com
POWER SUPPLY SPECIFICATIONS
Input Voltage: 115/230 VAC @ 60hz
Input Current: 0.8 amps Max.
Output Voltage: 12/24VDC (Special Applications)
Output Current: 1.5 amps
Ripple Voltage: 0.05 Volts Max
Battery Charger Max Current: 0.25 amps
Maximum recommended battery size: 7ah
(Replace batteries every three years)
To determine standby battery capacity, refer to
Batter Discharge table (INST-BDT).
Compatible UL listed Fire Devices:
Smoke detector manufactured by ESL, Model 521B,
521BXT with Model 506 module.
Suitable Uses:
Electric Lock Power Supply
Access Control Power Supply
Burglar Alarm System Power Supply
NOT INTENDED TO POWER A LOCAL
BURGLAR ALARM INDICATING DEVICE.
TEST UNIT YEARLY
COMPONENT LOCATIONS
STANDARD BOX
POWER
SUPPLY
BOARD
CONTROL
MODULE
CONTROL
MODULE
BATTERY 1
4ah
BATTERY 2
4ah
MAIN SYSTEM ON-OFF
OR
FIRE PANEL CONNECTION
Fire Panel
Contact (N/C)
Master ON/OFF
Switch (N/C)
+_
C
Figure C
C
+_
Min. Switch
OR
Contact Ratings
100mA @ 30vdc
12VDC
+_
12VDC
+_
JUMPER SET
FOR 24 VDC
+
-
JUMPER SET
FOR 12 VDC
12VDC
+_
+
-
12 Volt mode Battery
Connections
+
C
-
Battery
Charger
Indicator Fuse
AC Power
LED
Primary
Fuse 250V
1.5Amp
Battery
Input
Voltage Output
Terminals
12V
S
H
O
R
T
O
P
E
N
24V
VOLTAGE
SELECT
System Status
LED
Voltage
Adjust
Note:
Power must be
turned off before
changing voltage
jumper
See figures b & c for examples of
Master System On/Off Control
OR
Power Supply control from
the Fire Control Panel
FIGURE A
“A” OPTION BOX
POWER
SUPPLY
BOARD
CONTROL
MODULE
CONTROL
MODULE
BATTERY 2
4ah or 7ah
CONTROL
MODULE
CONTROL
MODULE
BATTERY 2
4ah or 7ah
FIGURE B
24 Volt mode Battery
Connections
NOTE:
Power limited cable
must maintain a 1/4”
or more spacing from
battery cables or
primary power wires.
_
Battery
+Power limited
Class 2 output
631RF
High voltage
Input
+- +-
C
Wire Routing
P:\INSTALLATION INST\Power Supplies\INST-631RF-CUL_631RFA-CUL.vsd Rev A 04-13
REGULATED POWER SUPPLY
INSTALLATION INSTRUCTIONS
MODEL 631RF-CUL/631RFA-CUL
801 Avenida Acaso, Camarillo, Ca. 93012
(805) 494-0622 • Fax: (805) 494-8861
POWER SUPPLY SPECIFICATIONS
Input Voltage: 115/230 VAC @ 60hz
Input Current: 0.8 amps Max.
Output Voltage: 12/24VDC (Regulated)
Output Current: 1.5 amps
Ripple Voltage: 0.05 Volts Max.
Battery Charger Max. Current: 0.25 amps
Maximum recommended battery size: 7ah
Recommended Battery: SDC Model RB12V7
(Replace batteries every 3 years)
To determine standby battery capacity refer to
Battery Discharge Table (INST-BDT).
Suitable Uses:
Electric Lock Power Supply
Access Control Power Supply
TEST UNIT ANNUALLY
Note: Power limited
cable must maintain a
1/4” or more of spacing
from battery cables or
primary power wires.
Battery
+C
_
HIGH
VOLTAGE
INPUT
POWER LIMITED
CLASS 2 OUTPUT
+_
+_+_
+_
COMPONENT LOCATIONS
MODEL 631RF-CUL/631RFA-CUL
BATTERY 1
4ah
POWER
SUPPLY
BOARD
BATTERY 1
4ah
STANDARD BOX
CONTROL
MODULE
CONTROL
MODULE
AC Power
LED
Note:
Power must be turned off
before changing voltage
jumper.
Voltage Adjust
Battery
Charger
Indicator
Battery
Input
Primary
Fuse 250V
1.5 Amp
Fuse
+_C
System Status LED
YEL = System OK
RED = No AC Input
GRN = No DC Output
S
H
O
R
T
O
P
E
N
12V 24V
Voltage
Select
Voltage Output
Terminals
BATTERY 2
4ah or 7ah
“A” Option Box
CONTROL
MODULE
CONTROL
MODULE
POWER
SUPPLY
BOARD
CONTROL
MODULE
CONTROL
MODULE
BATTERY 2
4ah or 7ah
COVER BATTERY MONITOR LEDS
GRN = AC
RED = BATTERIES
ORG = NO/LO BATTERY
MAIN SYSTEM ON-OFF Min. Switch or
Contact Ratings
100mA @ 30VDC
+_CMaster ON/OFF
Switch (N/C)
12VDC
+_+_
+_
12 Volt Mode Battery
Connections
Monitor Board
Install Jumper
12VDC
+_+_
12VDC
+_+_
24 Volt Mode Battery
Connections
Monitor Board
Remove Jumper
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere SDC Stromversorgung Handbücher
