SDX Audio MRDP-C01 Bedienungsanleitung

Sondpex Corporation of America

Princeton, NJ 08540, USA

1-877-997-7888

732-940-4430

support@sondpex.com

www.sondpex.com

Car Stereo Receiver and Audio Player

USER MANUAL AND INSTALLATION INSTRUCTIONS

Model:MRDP-C01

Thanks for your purchase!

Our car audio equipment lets you enjoy diversified functions and

enjoy superior music quality. We hope you enjoy this product.

INDEX

Caution P. 2

Installation P. 3

Specification P. 5

Button and key functions P. 6

Playback operation P. 7

Electrical Connection P. 9

Wiring diagram P. 10

Remote operation P. 11

Troubleshooting P. 13

CAUTION

This unit is designed to operate on 12-volts DC, negative

ground electrical system only, do not attempt to install this unit

in a vehicle having a positive ground system. Please do not

install the unit to a +24V truck, bus or RV, otherwise the

machine will be damaged.

You should not touch the high-polished playback head with any

metallic or magnetic tools.

Please do not replace the power fuse without professional

guidance. Improper use of fuses may cause damage or fire.

To avoid electric shock caused by short circuit, or any

unnecessary damage and fire, please prevent the product from

a wet environment and water.

Metal parts of this unit (especially on the back) become quite

hot during operation, to be careful to avoid touching parts other

than the handle immediately after removing the unit.

Note:

1. When the inside temperature of car is much higher or lower,

please adjust the temperature in car first, then use the machine.

2. Avoid suffering strong attack, which will damage structural

components of the machine.

3. Operate the unit in accordance with the instruction manual,

damage caused by mal-operation is not covered under warranty.

4. Your unit has built-in filtering to eliminate most of the noise that

might come through the power source. However, with some

vehicles, particularly older models, some clicking or other unwanted

noise might be present.

Page 1

Page 2

Installation

Precautions

• Choose the mounting location carefully so that the unit will not

interfere with the normal driving functions of the driver.

• Avoid installing the unit where it would be subject to high

temperatures, such as from direct sunlight or hot air from the heater, or

where, it would be subject to dust, dirt or excessive vibration.

• Use only the supplied mounting hardware for a safe and secure

installation.

• Be sure to remove the front panel before installation.

•If installation angle exceeds 60° from horizontal, the unit might not

give its optimum performance. (A)

Step-by-Step Installation:

Please refer to the illustration and detailed step-by-step installation below:

Front installation (B)

1. Instrument board.

2. Metal mantle

After putting the mantle in the instrument board, bend the steel of the

mantle making it fixed to the instrument board.

3. Fastening bolt.

Rear installation (C)

1. Instrument board

2. Nut

3. Spring washer

4. Bolt

5. Fastening bolt

6. Fixed steel

In order to improve anti-interference, please fix the steel on the car under

frame. You can bend the steel if you need to.

Align the faceplate with the radio making sure the connectors line up

before you push the faceplate into place. (D) (E)

Dismantling:

1. Remove faceplate and then the plastic frame. (F)

2. Insert the dismantling key into the key hole of the device. Wait until the

hook lock unlocks, and then remove the key and unit. (G)

3. Disconnect all the wires of the unit as well as the antenna plug.

Note:

Make sure that the front panel is the right way up when attaching it to

the unit as it cannot be attached upside down.

Do not press the front panel hard against the unit when attaching it. It

can be easily attached by pressing it tightly against the unit.

For safekeeping, always keep the front panel in the supplied

protective case and keep it at moderate temperature.

Do not press hard or give excessive pressure to the display window of

the front panel when attaching it to the unit.

Page 3

Page 4

Specification:

Main Unit

Power supplier…………………………...…12V (DC) negative ground

Dimensions……………………………..……………...189x138x50mm

Installation dimension…………………………………193x141x53mm

Load……………………………………………………………....4-8 Ω

Max output……………………………………………………....25Wx4

RMS output………………………………………………….….20Wx4

Frequency scope………………………………....87.5MHz-107.9MHz

Sensitivity……………………………………………………..…<26dB

MP3

Signal to noise ratio……..……………………………………….>35dB

Frequency………………………………………..(100Hz-10KHz)+6dB

Harmonic voltage distortion (1KHz)…………………………...….<5%

Channel Separation…………………………………………….....>35%

Stereophonic reproduction channel balancing……………………...3dB

Button and Key Function

POWER ON (OFF) / MUTE: When the mp5 is powered off,

short press to turn it on. Press and hold to turn off the unit. When

the mp5 is powered on, short press this button to mute. When the

unit is muted, press the button again or rotate the volume button

to unmute.

MODE CONVERSION: Short press the mode button to switch

audio between FM, audio/video in, or audio/video file. If an

audio/video file is not present, the audio/video input will be

transmitted. In the case of no audio/video input, the radio will

automatically come on when the mp5 is turned on.

VOLUME CONTROL: The volume rotary button regulates the

volume, pushing the button will enable you to select your

favorable Bass, Treble, Balance and Fade.

SETTING: Short press to go into the main menu interface and

you could select system preferences in the software profile, such

as language, page style and desktop.

CLOCK: Press the button, a clock icon will appear in the

center of the screen and will display the current time on the unit.

Press and hold the volume rotary button for 3 seconds to adjust

the time. Rotate the button to adjust the minute, and then press

and hold the button to adjust the hour and finally press and hold

the volume rotary button again to finish the setting.

EQ:Short press the EQ button to select Classic, Jazz, Pop sound

effects or no effect.

USB (HARD DISK) / SD CARD PLAY

When the mp5 is turned on, insert the external storage device

such as a USB flash drive (mobile HDD) or SD card, the mp5

will automatically play the audio files stored in latest external

storage device. When the mp5 is shut down, insert the USB flash

drive (mobile HDD) or SD card and once the mp5 is turned on,

the audio files will be played in USB-SD sequence. Pull out the

played external storage device, the system will automatically

return to FM state. Turn on the mp5 without an external storage

device, the system will automatically go to FM mode. The mp5

is able to play a mobile HDD that has no more than 1T amount.

Page 5

Page 6

PLAYBACK OPERATION

1. See the picture (4.1) to play the audio or video.

Short press to select the file upward or downward.

2. Play/pause

Short press on to play or pause the current music.

Hit this button to select current menu function confirmed by

main menu interface.

3. Backspace button

Short press either the “B/E” or “C” button on the remote control

to leave the current interface and return to the main menu

interface.

4. Shortcut key

(1) Switch the audio/ video button.

(2) Switch to play the files stored in USB or SD card.

5. Play mode for the audio frequency (4.2)

(1) Select the modes between the audio single-song play,

sequence play, shuffle play and cycle play.

(2) Turn on or turn off the shuffle function.

(3) Turn on or turn off browse play function. Each song

will be played for 10 seconds.

AUDIO RECEPTION OPERATION

1. The mp5 can store 18 radio stations (5.1)

FM1FM2FM3

There are 6 stations in every waveband.

2. In the state of audio reception, short press “B/E” to switch

the waveband. Press and hold the button “B/E” to start an

automatic search and memory function, the system will

automatically search the FM or AM radio stations and store

every found station.

3. A short press on means searching the radio station

manually, long press one of the number buttons to store the

current radio station to that number.

4. Frequency Range FM: 87.5MHZ –107.9 MHZ

VIDEO INPUT FUNCTION

Connect the ports of video input and audio input and switch to

the mode of video input, the screen will play the input video files

of the access facility AV. If the audio files of the access facility

are played, the mp5 will play the audio parts and AV IN will

appear as a hint on the screen. (5.2).

CAMERASWITCHING

1. When the car is in the reverse gear state, the screen will

automatically switch to the rear vision picture and the camera

begins to work. (5.3) the current played program will be

muted and the screen won’t display any picture.

2. When the car is in other gears state, the back-vision camera

will be shut down and will return to playing the current

program.

Page 7

Page 8

Electrical Connection

Many vehicles are pre-fitted with ISO connectors behind the dash,

including all the electrical cabling for a car radio. In such cases, the

connections fitted to the vehicle can be directly plugged into the car radio

connectors. Should your car not be pre-fitted with these connectors, we

strongly advise you to obtain the ISO wiring loom fitted with the male

connector for connection to your car radio either from a specialist shop or

from the concessionaire for your vehicle. Once obtained, you will only

need to connect your loudspeakers and the power supply to the ISO

connector, following connection instructions provided with same.

CAUTION:

Make sure your car battery is a 12 volt (6 filler caps) negative ground

system (if not, a converter will be necessary).

Before starting wiring connections, disconnect the power supply by

removing the fuse box.

Connect the power wire to one of the extra terminals of the fuse box.

Connect the black ground wire to a metal part of the car. It is

important to make good contact.

Make other wiring connections as shown

Replace the fuse in the yellow power lead wire.

WARNING:

INCORRECT WIRING OR OPERATION WILL VOID THE

WARRANTY OF THIS UNIT.

THE ISO CONNECTOR MUST NOT BE CUT.

THE UNIT HAS 2 SEPARATE AMPLIFICATION STEPS. WHEN

TWO SPEAKERS ARE CONNECTED DO NOT CONNECT

TOGETHER THE WIRES BUT CHOOSE FRONT OR REAR.

THE RED WIRE MUST BE CONNECTED BY CAR IGNITION

KEY IN ORDER TO AVOID THE CAR BATTERY FROM

BECOMING WEAK WHEN THE CAR WILL BE NOT USED FOR

LONG PERIOD OF TIME.

MRDP-C01 Wiring Diagram

Page 10

Page 9

Remote operation

Remote Control Layout:

Changing the batteries

Change the batteries if the remote only works when close to the unit or

doesn’t work at all. Make sure to distinguish the positive and negative

clearly.

Press the plug and pull out Put the new battery Put the plug into

The battery at the same time in the plug the remote

Note: Before use, make sure to pull out the small piece of plastic

between the battery and the remote control.

Page 11

Page 12

TROUBLESHOOTING

Before going through the check list, check wiring connection, if any of the

problems persist after check list had been made, consult your nearest

service dealer.

Symptom

Cause

Solution

Failure of being

powered on

The car ignition switch

is not ON

If the power supply is

properly connected to the

car accessory terminal

switch the ignition key to

“ACC”

The fuse is blown

Replace the fuse

No sound.

Volume is in

minimum.

Adjust volume to a

desired level

Wiring is not properly

connected.

Check the wiring

connection

Failure of Radio

Antenna is not pulled

out or connection is

wrong.

Properly connect the

antenna and pull it out as

long as possible

Weak signal

Rotate the antenna to

proper direction

The radio station

automatic selection

does not work.

The signals are too

weak.

Select a station manually

Failure of reading

USB or SD/MSD

Poor contact

Pull out the memory card

and reinsert it

Noises and sound

distortion

Speaker cables are

pressed by screws

Check the speaker cables

Speaker cables are

short-circuited

Properly connect wires.

Stop working

CPU can not work

normally

Turn off the power and

power it on again.

Files are damaged

Skip this file and please

select next file

1. Change the fuse

Please make sure the amperage matches will all other fuses before

changing them. If the fuse is burnt check the power supply first and then

change the fuse. If the fuse is burnt again there may be internal problems,

please contact the dealer.

2. Connector cleaning

If the connector of the unit and the panel is dirty the unit may not work

normally. In order to prevent this please remove the front panel and clean

the connectors with spirituous cotton as shown on the picture below.

CAUTION: For safety please switch off the engine and take the key out of

the ignition before you clean the connector. Do not use your fingers or any

metal to touch the connectors.

Note: This manual instruction is for reference. Design and specifications

are subject to be changed without notice.

Page 13

Page 14

Inhaltsverzeichnis

Andere SDX Audio Autoempfänger Handbücher

SDX Audio

SDX Audio RUSX123 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung