SEA GATE 2 Bedienungsanleitung

REV 04 - 11/2006

Automazione

Porte e Cancelli

GATE 2 - 24V PLUS

SEA (UK) Limited

Unit 6A Olton Wharf, Solihull B92 7RN

Tel. 0121 706 9629 - Fax 0121 764 56034

London Tel. 0208 360 8022

www.seaukltd.co.uk

e-mail: [email protected]

67410192

ELECTRONIC CONTROL UNIT FOR SWING OPERATORS 24 V D.C.

English

Deutsch

23001135

CONNECTIONS

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

CN1

1 2 3 4 5 6 7 8 9 10 1112

START

START Ped.

CN3

1 2 3 4 5 6 7 8 9 10

STOP

GND

CN4

Battery 24Vdc

1 2

CN2

1 2

GND

24V TXPhotocell

+12V Electriclock

Flashinglamp24V 15W

24 Vdc Accessoires

Common

PHOTOCELL

LIMITSWITCHOp1

LIMIT SWITCH Cl1

LIMIT SWITCH Op2

GND

POWERSUPPLY

AERIAL

230V ACINCOMING

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

CN4

CN3

DIP

CN1

Rv1

Rv2

Rv3

Rv4

RX CN2

LED1

LED10

LED6

LED5

LED4

LED3

LED2

LED9

LED8

LED7

LED1 = Programming Tx/selflearning / LED2 = Photocell / LED3 = Start / LED4 = Stop / LED5 = Start pedestrian / LED6 = Limit switch

opening motor 2 / LED7 = Limit switch closing motor 2 / LED8 = Limit switch opening motor 1/ LED9 = Limit switch closing motor 1 /

LED10 = Power supply / F1 = Fuse battery charge 250mA / RX = 433 Mhz receiver module CN1 = Connector for entries / CN2 = 230V

power supply connector / CN3 = Connector for exits / CN4 = Battery connector / Rv1 = Anti crush sensitivity adjustment / Rv2 = Speed

adjustment of leaves/ Rv3 = Leaf delay adjustment in closing /Rv4 = Pause time adjustment/ P1 = Push button for working time and

radio transmitter memorization / DIP = Dip-switch / T1 = Transformer

DESCRIPTION OF THE COMPONENTS

REV 04 - 11/2006

GATE 2 - 24V PLUS

Automazione

Porte e Cancelli

GENERAL INFORMATION ...........................................................................................................5

START, STOP, PEDESTRIAN START, ANTENNA CONNECTIONS ............................................6

PHOTOCELLS, LIMIT SWITCH CONNECTIONS ........................................................................7

ELECTRIC LOCK, FLASHING LAMP, RECEIVER CONNECTIONS ..........................................8

POWER SUPPLY AND MOTORS ARM - ALPHA - BETA CONNECTIONS................................9

RADIO TRANSMITTER TYPE SETTING (DIP-SWITCH)..........................................................10

WORKING MODE SETTING (DIP-SWITCH)..............................................................................10

FUNCTION LOGIC SETTING (DIP SWITCH).............................................................................11

ADDITIONAL FUNCTIONS (DIP-SWITCH) ................................................................................11

SENSITIVITY REGULATION OF AMPEROMETRIC SENSOR..................................................12

MOTOR SPEED ADJUSTMENT.................................................................................................12

LEAF DELAY ADJUSTMENT IN CLOSING ................................................................................12

PAUSE TIME ADJUSTMENT......................................................................................................12

LEDS DESCRIPTION 12

SELFLEARNING WORKING TIMES ..........................................................................................13

RADIO TRANSMITTER SELFLEARNING .................................................................................14

ALARMS AND MAINTENANCE DESCRIPTION ........................................................................14

TROUBLE SHOOTING ..............................................................................................................15

INSTRUCTIONS AND GUARANTEE..........................................................................................16

INDEX

English

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

GENERAL INFORMATION

GENERAL CHARACTERISTICS

The GATE 2 24V control unit has been designed to manage one or two low voltage swing gate operators with or without

electronic limit switches.

Its dimensions are very sma

matically.

ll and as well as the classic functions refered to by the dip-switch it has several other

features such as motor speed adjustment, amperometric sensitivity for anti crush, adjustment of leaf delay in closing

and alteration of pause time .

The self- learning of working tims is done auto

TECHNICAL CHARACTERISTICS

Control unit power supply

Absorbt power

Max. motor charge

Max. accessories charge

Max. Flash light charge

Environment temperature

Protection fuse (24V accessories)

Function logic

Opening/closing time

Time of pause

Thrust

Slow down

Entries on connecting terminal

Exit on connecting terminal

Board dimensions

Characteristics optional batteries

Characteristics of external enclosure

230V ~

10 W

70 W x 2

24Vdc 200mA

24Vdc 15W max.

-20°C +50°C

1 (250mA)

Automatic / Manual / Security / Dead man

In selflearning in programming phase

Adjustable with trimmer

In selflearning in programming phase

Battery power supply / Total opening /pedestrian

opening / Security /

Stop / limit switch opening and closing

Power supply accessories 24Vdc / Motors 24Vdc /

Flashing lamp 24Vdc / Electric lock 12Vdc /

Power supply TX photocell

156 x 100 mm

12V - 4 Ah / dimensions 90 x 70 x 108 mm

305 x 225 x 125 mm - Ip55

(+6 -10%) - 50/60 Hz

ARRANGEMENTS

For Health and Safety reasons it is important to carefully follow all advice and instructions in this manual. An

incorrect installation or a wrong use of the product can cause injury to persons.

Make sure that the installation has an adequate differential switch as prescribed by the law in force and local isolation at

the control panel.

For the installation of the electric cables use adequate rigid and/or flexible ducts.

Always separate the connection cables of low voltage accessoires from those of 115/230V~ power supply. To avoid any

interference use separate casings.

Max. length of the power supply cable between control unit and motors is 10m, using cables with 2,5 mm

section. 5

START (N.O.)

An impulse given to this contact opens and closes

the automation depending on logic selected. It can

be given by a key switch, a keypad, etc.

To connect the other devices refer to the related

instructions leaflets. (ie. loop detectors and

proximity switches)

PEDESTRIAN START (N.O.)

To obtain partial opening (only one leaf opening) connect the key-

switch wires as in the picture. It is possible to connect other

command devices (push button board, radio receiver, keypad).

Note1: The contact for partial opening is a N.O. Contact (Normally

open)

Note2: Partial opening will always operate the M1 motor.

START - STOP - PEDESTRIAN START - ANTENNA

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

CN1

1 2 3 4 5 6 7 8 9 10 11 12

STOP (N.C.)

The pressure on this button immediately stops the motors in any

condition /position. A start command is needed to re-start movement.

Notice: If stop button not used a link is required between terminals n° 2

and 10.

ANTENNA

Connect the antenna

as in the picture.

N.O.

N.C.

-+ +C C

Photocells 1 Connection

When the photocells beam is crossed, the

automation reverses its movement if in

closing phase.

To use photocell self-testing, connect positive

(+) to terminal 5 instead of 10 (CN3).Tx only

Notice: If photocell not used a link is

required between terminals 5 and 10

(CN1).

+ = 24Vdc - = 0Vdc C = Contact

910

PHOTOCELLS/LIMIT SWITCH

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

CN1

1 2 3 4 5 6 7 8 9 10 11 12

CN3

1 2 3 4 5 6 7 8 9

Limit Switch 1 M2

Limit Switch 2 M2

Limit Switches

They can be of different types:

- inductive limit switch

- mechanical limit switch with lever

- limit switch with spring

- limit switch for motor-reducer with chain.

All these limit switches must be manufactured by

SEAfor compatibility with the connectors

Com = Common

N.B. If limits not used a link is required between

terminal 6 to 10.

Limit Switch 1 M1

Limit Switch 2 M1

Photocell

self-testing

Com

N.C.

CCom

Com

Limit Switches

They can be of different types:

- inductive limit switch

- mechanical limit switch with lever

- limit switch with spring

- limit switch for motor-reducer with chain.

All these limit switches must be manufactured by

SEAfor compatibility with the connectors

Com = Common

N.B. If limits not used a link is required between

terminal 8 to 10.

Electric lock exit

An electric lock of 12Vdc 15W max can be

connected .

The electric lock activates at every

opening cycle for about 1,5 sec. 8

ELECTRIC LOCK/FLASHING LAMP/

RECEIVER

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

C C

CN3

1 2 3 4 5 6 7 8 9

Flashing Lamp 24V 15W

The flashing lamp gives warning that the gate is moving.

To connect, wire the flashing lamp as in the picture.

It is possible to activate a pre-flashing of 3 seconds (Dip 8

to ON position).

+ + -

Connection of a radio

receiver

This connection allows

full opening/closing of

the automation. For the

receiver connection

make reference to the

r e l a t e d i n s t r u c t i o n

manual.

+ = 24Vdc,

- = 0Vdc,

C = Contact NO

Com = Common

CN1

1 2 3 4 5 6 7 8 9 10 11 12

CN1

Com

CN3

1 2 3 4 5 6 7 8 9

Motor 2

Output for Motor 2

connection

M+ = OPEN/CLOSED

M- = CLOSED/OPEN

Power input

Input for the connection of the electric power.

P = PHASE - LIVE

N = NEUTRAL NOTICE: for the connection to the

electric power see the law in force.

POWER SUPPLY - MOTORS ARM-ALPHA-BETA

GATE 2 - 24V PLUS

REV 04 - 11/2006

Automazione

Porte e Cancelli

C C

CN3

CN2

1 2

ARM

M+

4ALPHA STD

BETA

ARM

BETA

M+

M- M-

ALPHA STD

ALPHA PLUS

Motor 1

Output for Motor 1

connection

M+ = OPEN/CLOSED

M- = CLOSED/OPEN

ALPHA PLUS

3 4 5 6 7 8 9 10 11 12

CN1

Com

C C

CN1

C C

DIP-SWITCH (TYPE OF RADIO TRANSMITTER)

GATE 2 - 24V PLUS

REV 04 - 11/2006

DIP

Automazione

Porte e Cancelli

1 2 3 4 5 6 7 8

POSITION

OFF / OFF

ON / OFF

SETTING DIP1 AND DIP2 ACCORDING TO THE TYP OF RADIO TRANSMITTER USED

Radio transmitter SMART Dip-switch and/or radio transmitter HEAD Dip-switch

Radio transmitter SMART Fixed code and/or radio transmitter HEAD Rolling code

DIP

1 / 2

ON / ON

Radio transmitter HEAD e-copy

Erase the radio transmitter*

1 / 2

*Modality to erase learned radio transmitter.

Set the Dip 1 and 2 on ON.

Press and keep pressed P1 of the control unit for 10 seconds, the LED will switch on to confirm the executed cancellation.

Bring back the dip-switches into the position regarding the type of transmitter to be memorised.

DIP-SWITCH (OPERATION MODE)

POSITION

OFF / OFF

ON / OFF

SETTING OF DIP6 AND DIP7 RESPECTIVELY THE DESIRED WORKING MODE

Position to select the operational mode: two motors with limit switch

Position to select the operational mode: only one leaf with limit switch (M1)

DIP

6 / 7

OFF / ON

ON / ON

Position to select the operational mode: two leaves without limit switch (see note)

Position to select the operational mode: one leaf without limit switch (M1) (see note)

6 / 7

2. Switch on the power keeping push button P1 on the board pressed continuously.

3. The LED blinks slowly to confirm the memorisation of the operational mode.

4. Switch off the board and reset Dip 6 and 7 to OFF position. Now start self learning mode as explained on the next page.

Note:

To use the board without limit switch it is neccessary to bridge the limit switch inputs in closing to common

(Terminals 6 to 10 for single leaf operation and terminals 6 and 8 to 10 for paired operation).

1. ATTENTION! With power switched off, choose the type of gates (one or two motors) and if limit switches are

fitted, select the operation mode using DIP 6 and 7 and program as below. When set proceed with self-learning.

Andere Handbücher für GATE 2

Inhaltsverzeichnis

Andere SEA Steuereinheit Handbücher

SEA

SEA GATE 2 Bedienungsanleitung

SEA

SEA USER 1 - 24v DG R1 Bedienungsanleitung

SEA

SEA GATE 2 - 24V PLUS Bedienungsanleitung

SEA

SEA GATE 2 DG R1B Bedienungsanleitung

SEA

SEA SWING 2 DG R2F Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

SEA

SEA GATE 1 DG R1 Bedienungsanleitung

SEA

SEA USER 1-24V Bedienungsanleitung

SEA

SEA CUBE R. NW Bedienungsanleitung

SEA

SEA SLIDE DG R2F Bedienungsanleitung

SEA

SEA 23001157 Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

SEA

SEA USER 1 - 24v DG R1 Bedienungsanleitung

SEA

SEA SWING 2 Bedienungsanleitung

SEA

SEA 9521 Bedienungsanleitung

SEA

SEA USER1-24V Bedienungsanleitung

SEA

SEA USER 1 - 24v DG R1 Bedienungsanleitung

SEA

SEA UNIGATE 1I Bedienungsanleitung

SEA

SEA GATE 1 DG R1 Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

SEA

SEA Orion Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

SEA

SEA GATE 1 DG R2BF Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung