Seafloor TriDrone Programmierhandbuch

- TriDrone USV

- TriDrone Carry Case

- TriDrone Hardware Kit

- Data Collector Cable

- Accessory Pouch

-Spektrum Remote

Control with case

-USB Drive

-Mast

IMPORTANT

THANK YOU FOR PURCHASING SEAFLOOR SYSTEMS' PRODUCTS FOR YOUR SURVEYING NEEDS.

Please read through all of these Instructions and tips before proceeding with the operation. We do our best

to provide a simple setup process for all applications however please contact your nearest authorized

dealer if you encounter issues.

Always disconnect any power sources connected to your vessel before servicing vessel or accessories.

PRODUCT INCLUDES:

STEP: 1

Remove the vessel from the

case. Remove the remote case

from the top of the lid. Remove all

accessories from accessory pouch

located at the bottom of the case.

QUICKSTART INSTRUCTIONS

TriDrone Portable Remote Surveying Vessel

QUICKSTART INSTRUCTIONS

STEP: 2

Attach the thruster to the rear bracket of the vessel and secure by tightening

retaining screw.

STEP: 3

Insert fully charged 4S battery

and connect to power

distribution cable.

STEP: 4

Open bow hatch lid with provided hatch wrench,

and remove lid.

STEP: 5

Run the data collector cable through the inside of the hull through to the

hull hatch lid.

QUICKSTART INSTRUCTIONS

STEP: 6

Connect data collector cable to

transducer.

STEP: 8

Connect the thruster cable to the bulkhead

located at the stern of the vessel.

STEP: 7

Attach antenna to the mounting screw located at the front of the frame.

QUICKSTART INSTRUCTIONS

Operation: Be sure to observe and follow all local water safety regulations and procedures. Always

operate vessel within line of sight, and immediately stop operation if hazards or safety risks arise.

Your setup is now complete.

Welcome to the Seafloor Squad!

WARRANTY INFORMATION

For warranty information, visit https://www.seafloorsystems.com/terms-and-conditions 4415 Commodity Way, Shingle

Springs, CA, 95682 • 530-677-1019 https://www.seafloorsystems.com/

STEP: 9

Switch power to the "On" position.

STEP: 10

Connect the remote by holding the power button for

approximately 2 seconds. The remote will beep when

activated. You are now ready to survey.

Inhaltsverzeichnis

Andere Seafloor Schiffsausrüstung Handbücher

Seafloor

Seafloor Sonarmite Bedienungsanleitung

Seafloor

Seafloor AutoNav PLUS Bedienungsanleitung

Seafloor

Seafloor HyDrone ASV Bedienungsanleitung

Seafloor

Seafloor EchoBoat 160 ASV Bedienungsanleitung

Seafloor

Seafloor HydroCat 180 Bedienungsanleitung

Seafloor

Seafloor EchoBoat-240 Bedienungsanleitung

Seafloor

Seafloor HydroLite-DFX Bedienungsanleitung

Seafloor

Seafloor AutoNav Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Clarion

Clarion GR10BT Reparaturanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung

Sonic

Sonic 2024 Bedienungsanleitung