Seagate MEDALIST 1080SL Bedienungsanleitung

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Medalist 1080sl

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .

SCSI Interface Drive

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation Guide

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Publication Number: 36325-001, Rev. A, August 1995

Seagate, Seagate Technology and the Seagate logo are regis-

tered trademarks of Seagate Technology, Inc. MedalistSL, Sea-

FAX, SeaFONE, SeaBOARD and SeaTDD are trademarks of

Seagate Technology, Inc. Other product names are registered

trademarks or trademarks of their owners.

Seagate reserves the right to change, without notice, product

offerings or specifications. No part of this publication may be

reproduced in any form without written permission from Seagate

Technology, Inc.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 1

Read before you begin...

. . . . . . . . . . . . . . . . . . 3

Configuring the drive . . . . . . . . . . . . . . . . . . . . 5

Attaching cables . . . . . . . . . . . . . . . . . . . . . . 10

Mounting the drive . . . . . . . . . . . . . . . . . . . . . 11

Configuring the drive and computer . . . . . . . . . . . 12

System setup configuration . . . . . . . . . . . . . . . . 12

Low-level formatting . . . . . . . . . . . . . . . . . . . . 12

Partitioning . . . . . . . . . . . . . . . . . . . . . . . . 13

High-level formatting . . . . . . . . . . . . . . . . . . . 14

NonDOS operating systems . . . . . . . . . . . . . . . 15

Network installation . . . . . . . . . . . . . . . . . . . . 15

Basic troubleshooting . . . . . . . . . . . . . . . . . . . 16

Advanced troubleshooting . . . . . . . . . . . . . . . . 18

Technical support services . . . . . . . . . . . . . . . . 21

Storing and shipping your drive . . . . . . . . . . . . . . 24

Introduction

Thank you for choosing a Seagate drive. The purpose of this

guide is to assist you with installing your new hard drive. Its

organization outlinesthecomplete installation processfromhan-

dling the drive and drive application in Before you begin... to

offering troubleshooting suggestions and technical support infor-

mation. The topics discussed are:

•Handling your drive (see Before you begin...)

•Configuring the drive

•Attaching cables to the drive

•Mounting the drive

•Configuring the computer

•Troubleshooting

•Where to call for Seagate technical support

We hope your installation goes smoothly, but if complications

arise,alistof commonsymptomsandsolutionsisprovidedinthe

troubleshooting section. If the problem persists, contact your

dealerfirst.Yourdealerisfamiliarwith systemintegrationandthe

conflicts that arise. If you need additional help or information

about Seagate products, Seagate technicalsupport numbersare

provided.

Medalist 1080sl SCSI Installation Guide,August 1995 1

Drive features

Formatted Capacity (Mbytes) 1080.23

Total sectors 2,109,840

Cylinders 4,826

Physical heads 4

Sectors per track (average) 109

Bytes per sector 512

Spindle speed 5,376 RPM

Average seek time (msec) 12.5 msec

Cache (segmented) 128 Kbytes

Internal transfer rate (Mbits per second max) 33 MHz to

65 MHz

External transfer rate (Mbytes per second max)

Asynchronous

Synchronous 5.0

10.0

Power on to Ready 20 sec

Seek power (typical) 7.11W

Drive acoustics, Idle mode 30 dBA

2 Medalist 1080sl SCSI Installation Guide, August 1995

Read before you begin...

Note. Throughout this manual the Medalist 1080sl SCSI is

referred to by its model number, ST51080N.

Application. YourSeagate® drive is designed for IBM and IBM-

compatible personal computers, Macintosh and other systems

using the SCSI interface.

Turn off the system power before attempting any installation.

Static discharge. Observe the followingprecautions:

•Keep the drive in its static-shielded bag until you are ready to

complete theinstallation.Donotattach anycablestothedrive

while it is in its static-shielded bag.

•Handle the drive by its edges or frame, and do not touch the

I/O connector pins or the circuit board.

•Before handling any components, put on a grounded wrist

strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet.

•Use antistatic padding on all work surfaces.

•Avoid static-inducing carpeted areas.

Drive handling. The drive is extremely fragile—handle it with

care. Do not attach labels to any part of the drive.

Inspection. After you are familiar with the handling precautions

listed above, inspect the drive. If it appears to be damaged, call

your distributor or dealer immediately.

Warranty. See your authorized Seagate distributor or dealer.

Maintenance and repair. Seagate drives do notrequire mainte-

nance. The head/disc assembly is sealed; if you break the seal,

Medalist 1080sl SCSI Installation Guide,August 1995 3

you voidthe warranty. Seagate customer service centers are the

only facilitiesauthorized to repairSeagate drives. Seagate does

not sanction any third-party repair facilities.

Shipping. Keep your original box and packing materials for

transporting or shipping your drive. The box has a

Seagate

Approved Package

label. Shipping a drive in a nonapproved

container voids the warranty. Call your authorized Seagate dis-

tributor to purchase additional boxes.

Radio and television interference. This product complies with

ClassBlimitsforradionoiseemissionsfromcomputerequipment

as set out in the radio interference regulations of the Canadian

Department of Communications.

Le présent appareil numérique néémet pas de bruits radioélec-

triques depassant les limites applicable aux appareils numéri-

ques de Classe B prescrites dans le règlement sur le brouillage

radioélectrique edicté par le Ministère des Communications du

Canada.

Sicherheitsanleitung

1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umge-

bungstemperatur von 55°C vorgesehen ist.

2. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32

UNC-2Abenötigt.BeiseitlicherBefestigungdarfdiemaximale

Länge der Schrauben imChassis nicht mehr als 5,08 mm und

bei Befestigung an der Unterseite nicht mehr als 5,08 mm

betragen.

4 Medalist 1080sl SCSI Installation Guide, August 1995

3. Als Versorgungsspannugen werden benötigt:

+5V æ 5% 0,65A

+12V æ 5% 0,45A (1,9A fur ca. 10 Sek. fur æ 10%)

4. Die Versorgungsspannung mub SELV entsprechen.

5. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebilde-

tem Servicepersonal durchgeführt werden. Bitte schaffen Sie

Festplatteetiketten nicht weg.

6. Der Einbau des Drives mub den Anforderungen gemäb DIN

IEC 950V DC 0805/05.90 entsprechen.

Configuring the drive

Required materials:

2-mm jumper connector (supplied as spare jumpers)

Your Seagate drive is configured for operation using the options

jumper block (J8) shown in Figure 1 on page 6. The settings for

theavailableconfigurations areshowninFigure2onpage7.The

options jumper block (J8) allows you to:

•Set the SCSI ID

•Connect a remote LED

•Enable or disable parity

•Enable or disable the drive’s terminator

•Select the termination power source

SCSI ID settings. Each device on the SCSI bus must be as-

signed a unique SCSI ID. The drive uses pin-pairs1 and 2, 3 and

4, and 5 and 6 on the options jumperblock (J8) forassigning the

ID. The chart in Figure 2 shows you how to place the jumpers to

Medalist 1080sl SCSI Installation Guide, August 1995 5

J3. Standard

power connector

1234

J1. Interface

connector

J8. Options jumper block

+5V

+5V return

+12V return

+12V

Circuit

board

J1 pin 1

J8 pin 1

Figure 1. Connector and jumper block locations

6 Medalist 1080sl SCSI Installation Guide, August 1995

SCSI ID 0

SCSI ID 1

SCSI ID 2

SCSI ID 3 (default)

SCSI ID 4

SCSI ID 5

Note.

1. All other pins

are reserved. Do

not use them.

2. Jumpers on

pins 28 and 30

and 32 and 34

are spares; these

pins do not

require jumpers.

SCSI ID 6

SCSI ID 7

Remote LED 

connection

Reserved 

Do not use

Remote start

Enable parity (default)

Disable terminator

(default is enable)

Power to drive

terminator only

Power from bus, drive

terminator disabled

Power to drive

terminator and to

SCSI bus (default)

Power to SCSI

bus only

J8. Options jumper block Circuit board

side up.

11

9

7

5

3

13

1

15

17

19

21

33

31

29

27

25

23

Spares

Figure 2. Options jumper settings

Medalist 1080sl SCSI Installation Guide, August 1995 7

assign ID values0 through 7. Be sure that the ID you choose is

not used by another device on the SCSI bus.

YourSeagate driveis shippedby the factory configuredas SCSI

ID 3—jumpers are attached to pins 3 and 4 and pin 5 and 6. You

must reconfigure the SCSIID if another device is assigned SCSI

ID 3 or if you are making the drive the bootable drive. The

bootable drive must be Drive C. It must be assigned the ID

number your SCSIadapterrecognizes as the first positionon the

bus. Usually, this is SCSI ID 0 (refer to your SCSI host adapter

documentation).

If installing your new drive puts more than two drives on the bus,

your SCSI adapter may require thatyou install a device driver or

that you reconfigure its onboard BIOS. Refer to your SCSI

adapter’s user guide for instructions on how to install the third

drive.If a device driver isrequired, it will beprovided bythe SCSI

adapter manufacturer.

Remote LED. You can connect a remote LED to the drive using

pins 9 and 10 on jumper block J8. Connect the LED ground wire

(usually the black wire) to pin 9.

Remote start. This setting causes the drive to wait for a specific

commandfromthehostbeforeitstartsorstopsthespindlemotor.

Parityenable.Parityisamethodthatissometimesusedforerror

detection. The drive is shippedwith parity enabled.

Terminators. The drive is designed with single-ended drivers

andreceiversandmustbeusedwithotherSCSIdevicesthatuse

single-ended drivers and receivers. These systems require that

terminators be used at both ends of the SCSI bus to ensure the

integrity of the signal. The drive has built-in terminators that can

be enabled or disabled as required. It is shipped with the termi-

8 Medalist 1080sl SCSI Installation Guide, August 1995

Andere Handbücher für MEDALIST 1080SL

Inhaltsverzeichnis

Andere Seagate Lagerung Handbücher

Seagate

Seagate EXOS 512E Series Bedienungsanleitung

Seagate

Seagate ST902503FGA2E1-RK Bedienungsanleitung

Seagate

Seagate Medalist 10240 Bedienungsanleitung

Seagate

Seagate Medalist ST31276A Bedienungsanleitung

Seagate

Seagate STD124000N Bedienungsanleitung

Seagate

Seagate ST2000NX0243 Bedienungsanleitung

Seagate

Seagate ST9120817AS - Momentus 5400.4 120 GB Hard... Bedienungsanleitung

Seagate

Seagate ST9100824A - Momentus 5400.2 100 GB Hard... Bedienungsanleitung

Seagate

Seagate ST31000322CS - Pipeline HD 1 TB Hard Drive Bedienungs- und Sicherheitshinweise

Seagate

Seagate ST310014ACE - U Series X 10 GB Hard Drive Bedienungsanleitung

Seagate

Seagate Savvio 15K Bedienungsanleitung

Seagate

Seagate ST446452W Bedienungsanleitung

Seagate

Seagate SkyHawk AI Bedienungsanleitung

Seagate

Seagate Momentus 5400.3 ST9100828SB Bedienungsanleitung

Seagate

Seagate SAVVIO ST9900805SS Bedienungsanleitung

Seagate

Seagate BARRACUDA 9 Bedienungsanleitung

Seagate

Seagate Momentus 4200 N-Lite ST940110A Bedienungsanleitung

Seagate

Seagate FreeAgent GoFlex TV Bedienungsanleitung

Seagate

Seagate CTT 8000 Bedienungsanleitung

Seagate

Seagate BlackArmor PS 110 Bedienungsanleitung

Seagate

Seagate Computer Drive Bedienungsanleitung

Seagate

Seagate BlackArmor WS 110 Bedienungsanleitung

Seagate

Seagate ST400FM0093 Bedienungsanleitung

Seagate

Seagate ST32122A - Medalist 2.1 GB Hard Drive Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung