Seagate Medalist 1721 Bedienungsanleitung

......................................

Medalist 1721 (ST31721A)

......................................

Medalist 1010 (ST31010A)

......................................

for ATA (IDE)-Compatible PCs

......................................

Installation Guide

......................................

-2 Medalist 1721, 1010, Rev. B

Publication Number: 21200092-001, Rev. B, March 1999

Seagate, Seagate Technology, and the Seagate logo are regis-

tered trademarks of Seagate Technology, Inc. Medalist, DiscWiz-

ard, SeaFAX, SeaFONE, SeaBOARD, and SeaTDD are either

trademarks or registered trademarks of Seagate Technology,

Inc. or one of its subsidiaries. All other trademarks or registered

trademarks are the property of their respective owners.

Medalist 1721, 1010, Rev. B -1

Contents

What you need........................................................................ 1

Before you begin .................................................................... 1

Handling precautions............................................................. 2

Master/slave jumpers............................................................. 3

Attaching cables and mounting the drive............................ 5

Configuring your computer................................................... 8

Addressing drive capacity limitations................................ 10

Partitioning and formatting your drive............................... 12

Installation using Disk Manager........................................ 13

Windows 95 or Windows 98 installation ........................... 14

Standard DOS installation................................................ 15

Additional installation options............................................ 17

Non-ATA compatible slave jumper...................................... 17

Cable select jumper ............................................................. 18

Advanced Disk Manager options........................................ 19

Troubleshooting ................................................................... 22

Seagate Technology support services............................... 28

Storing and shipping your drive......................................... 34

iii

0 Medalist 1721, 1010, Rev. B

Medalist 1721, 1010, Rev. B 1

What you need

•Straight-edge and Phillips screwdrivers

•Four 6-32 UNC drive mounting screws

•An ATA host adapter and interface cable (max length: 18

inches) with enough connectors for all your drives

•An unused drive power cable for your new drive

•A bootable DOS system diskette (Seagate recommends using

DOS Version 5.0 or later.)

•If you are mounting this 3.5-inch drive in a 5.25-inch drive bay,

you need a mounting adapter or frame kit. Also, you may need

drive mounting rails if your drive bay is not designed for direct

mounting.

Before you begin

•Make sure your computer is turned off before you open the

case.

•Read the handling precautions following and inspect the drive

to make sure that it is not damaged.

•Save your foam-lined Seagatedisc drive box. Seagate has

approved this box for shipping a Seagate disc drive. Using any

other container or packing material voids your drive warranty.

2 Medalist 1721, 1010, Rev. B

Handling precautions

Disc drives are extremely fragile. Do not drop or jar

your drive.

Keep the drive in its antistatic bag until you are

ready to install it.

Protect your drive from static discharge by making

sure you are well grounded before touching the

drive. We recommend wearing a grounded wrist

strap throughout the installation process. Do not

touch the connectors or any part of the printed cir-

cuit board.

Always handle the drive by its edges or frame.

Do not apply pressure or attach labels to the circuit

board or the top of the drive.

Medalist 1721, 1010, Rev. B 3

Master/slave jumpers

If your new Seagatedrive will be the only drive in your computer,

you do not have to change any jumper settings. In this case, skip

ahead to “Attaching Cables and Mounting the Drive,” on page 5.

If you already have one hard drive in your computer and you are

installing a second drive, you must configure one drive as a mas-

ter and the other as a slave.

To configure the drive as a master or one drive only:

•Place a jumper on pins 5 and 6 (see Figure 1 on page 4).

The master drive usually defaults to being the “boot” drive

(drive C), from which the computer loads system software

when it first starts up.

To configure the drive as a slave:

•Remove all the jumpers.

•If you need to change the jumpers on your existing hard drive,

see the Disk Manager online manual, look on the drive label,

or contact the drive manufacturer.

4 Medalist 1721, 1010, Rev. B

Figure 1. Master and slave jumper settings

pin 1

ATA interface

connector

135

246

Slave

Master or single drive

4-pin power

connector

Medalist 1721, 1010, Rev. B 5

Attaching cables and mounting the drive

1. If you are attaching a new ATA interface cable to a single

drive, attach one end of the cable to the interface connector

on your host adapter or motherboard. Motherboard connec-

tors can be identified by the IDE or HDD 40-pin connector.

The ATA cable must be no more than 18 inches (457 mm)

long.

2. Thread the interface cable through the drive bay and attach

the connector at the end of the interface cable to your new

drive.

Note. If you have two drives, attach the second drive to the sec-

ond connector.

Figure 2. Attaching the cables

Caution. To avoid possible damage to your system,

make sure to align pin 1 on the host adapter or mother-

board with pin 1 on your drive or drives. Pin 1 on the

interface cable is usually indicated by a stripe along the

edge of the cable.

Pin 1

Host

adapter

6 Medalist 1721, 1010, Rev. B

Figure 3. Mounting screws

3. You can mount the drive in any orientation. Usually it is

mounted with the circuit board down.

4. Slide the drive carefully into the drive bay. Secure the drive

with four 6-32 UNC mounting screws in either the side-

mounting holes or the bottom-mounting holes. Insert the

screws no more than 0.22 inch (5.58 mm) into the bottom-

mounting holes and no more than 0.20 inch (5.0 mm) into the

side-mounting holes.

Caution. To avoid possible damage to the drive, do not

overtighten the screws or use metric screws.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Seagate Lagerung Handbücher

Seagate

Seagate BARRACUDA GREEN ST2000DL003 Bedienungsanleitung

Seagate

Seagate ST3300657SS - Cheetah 300 GB Hard Drive Bedienungsanleitung

Seagate

Seagate FreeAgent Pro Bedienungsanleitung

Seagate

Seagate Medalist Pro Series Bedienungsanleitung

Seagate

Seagate ST9120315AS - Momentus 5400.6 120 GB Hard... Bedienungsanleitung

Seagate

Seagate Barracuda ST1000DM003 Bedienungsanleitung

Seagate

Seagate HAWK 4 Bedienungsanleitung

Seagate

Seagate ST500LX003 Bedienungsanleitung

Seagate

Seagate ST336705LW Bedienungsanleitung

Seagate

Seagate Constellation ES Bedienungsanleitung

Seagate

Seagate Video 2.5 Bedienungsanleitung

Seagate

Seagate FreeAgent Go 160GB Bedienungsanleitung

Seagate

Seagate EXOS ST16000NM002G Bedienungsanleitung

Seagate

Seagate Duet Bedienungsanleitung

Seagate

Seagate Medalist 6540 Bedienungsanleitung

Seagate

Seagate 600 Pro SSD Bedienungsanleitung

Seagate

Seagate Pipeline HD ST1500VM002 Bedienungsanleitung

Seagate

Seagate ST32000641AS - Barracuda XT 2 TB Hard Drive Bedienungsanleitung

Seagate

Seagate Expansion Portable Drive 1TB Bedienungsanleitung

Seagate

Seagate Expansion Bedienungsanleitung

Seagate

Seagate Cheetah 18LP Bedienungsanleitung

Seagate

Seagate ST3120020A Bedienungsanleitung

Seagate

Seagate ST43400N/ND Bedienungsanleitung

Seagate

Seagate ST34501N Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung