SeaHawk LD1500 Bedienungsanleitung
L D 1 5 0 0
QUICK START GUIDE LD1500
1. SeaHawk LD1500 Installation
The LD1500 is a panel mounted device. There are four mounting holes on the sides of the unit spaced 6.6 inches
(.167m) apart. Use drywall anchors if securing the unit to drywall.
2. Connecting the Water Leak Detection Cable
The LD1500 requires a leader cable (included in the leader cable kit: part #LC-KIT). One end of this leader cable
connects into the LD1500. This end of the cable has four stripped, bare wires. The other end features a mating
connector which connects with the SeaHawk Water Leak Detection Cable (SC). The end of the cable is finished with
a removable End-of-Line terminator (EOL).
Connect the 15 foot (4.57m) leader cable to the LD1500. From left to right, with the screws of the terminal block
connector facing up, the wires that screw into the terminal connector should be colored: white, black, green, and
red. If the terminal connector is removed from the end of the cable, make sure the wires are in this same order when
the connector is reapplied.
Once the leader cable is plugged into the terminal blocks, it is ready to be connected to the SC cable. To do this,
unscrew the end terminator (EOL) from the end of the leader cable. Attach the first length of SC cable to the leader
cable. Route the SC cable according to a cable layout diagram; see Section 3-2.1, pg. 6, of the Product User Guide
for detail about the layout diagram. Secure the EOL terminator on the unoccupied end of the SC cable.
Supplies for Installation
LD1500 Unit
SeaHawk Leak Detection Cable (SC)
24 VDC or 24 VAC (recommended)
Wall Adapter, part #WA-DC-24-ST
Cross Over Cable (blue with yellow ends)
Leader Cable Kit (purchased separately)
End Terminator (EOL)
15ft. (4.57m) leader cable
P1 TB1
Power
TB2
Cable
Interface
P2
RJ45
SW1 TB3
EIA-485
P4
EIA-232
Craft Port
RGBW
Leader CableSensing Cable
End
Terminator
(part # LC-Kit)
L D 1 5 0 0
A
lthough the information contained in this document is believed to be accurate and correct, RLE Technologies assumes no responsibility, and
disclaims all liability, for any damages resulting from the use of this information or any error or omission in this document. RLE Technologies does not
warrant, guarantee, or make any representations as to the performance, fitness for use, safety, or reliability of any existing or future wiring, equipment,
additions or modifications to equipment, or any other component of the original or modified system. Specifications are subject to change without
notice. 110070 Rev 1.0 (1/2009) ©2009 RLE Technologies
104 RACQUETTE DRIVE
FORT COLLINS CO 80524
WWW.RLETECH.COM
970 484-6510
3. Apply Power to the Unit
The LD1500 operates on either 24VAC or 24VDC power. A power supply should be run to the location of the
unit. RLE recommends the use of a 24VDC wall adapter power supply (part # WA-DC-24-ST), which is available
separately. The LD1500 should begin booting upon applying power. Wait approximately one minute. No alarm
should be present.
4. Communication
Note: Consult your IT Department before attempting this. The LD1500 comes from the factory with a default
IP address of 10.0.0.188,a default Subnet Mask of 255.255.255.0 and a gateway (Def. Route) of 10.0.0.1.
Depending on the user’s network configuration the LD1500 may not communicate over a user’s network initially.
The default address must be changed to an IP address that corresponds with the user’s network before the
LD1500 can communicate over the network.
5. Set the IP Address
There are two ways to set the IP address: via the Web browser or via the RS232 interface:
Web Browser
To set the IP address using a Web browser, first plug the crossover network cable (blue with yellow ends) that
shipped with the LD1500 unit into the laptop or workstation that will be used to configure the LD1500. This cable
is not intended to be connected to a network hub. Write down the computer’s IP address and Subnet Mask. Then
change the IP address and Subnet Mask of the computer from its existing address to one that will allow it to
communicate with the LD1500, such as 10.0.0.185.
Connect the other end of the crossover network cable to the Ethernet port on the LD1500. Access the unit
through a Web browser by typing the LD1500’s default IP address (10.0.0.188) into the location bar. Enter the
LD1500 user name when prompted (Default Username: ld1500, Default password is blank). Select the
Configuration Menu link, then select the Network Settings link. Change the IP settings to those provided by the
network administrator. Press the Submit Changes button. The unit will save the new IP address and reboot.
Once the LD1500 reboots, the system status LED on the front of the unit will stop flashing. You may now use the
new LD1500 IP address and reset the computer to its original IP address and Subnet Mask. This may require
assistance from your IT Department. The LD1500 is now configured to communicate on the network. Connect
the PC and the LD1500 to the network. From the PC Web browser, type in the new IP address of the LD1500.
Enter the user name and password as stated above to verify network access to the LD15000.
EIA-232 Interface
To set the IP address using the RS232 interface, see the LD1500 User Guide available on the Product User
Guide CD (included with your LD1500), or download the Product User Guide from the LD1500 webpage located
on our website at www.rletech.com.
Inhaltsverzeichnis
Andere SeaHawk Controller Handbücher
