SeaLevel COMM+8.422.PCIe Bedienungsanleitung

COMM+8.422.PCIe

User Manual | 7802e and 7802eS

Contents

CONTENTS...........................................................................................................................................................2

INTRODUCTION ................................................................................................................................................... 3

BEFORE YOU GET STARTED ...............................................................................................................................4

HARDWARE DESCRIPTION ................................................................................................................................. 6

HARDWARE CONFIGURATION............................................................................................................................7

INSTALLATION & CONFIGURATION.................................................................................................................10

TECHNICAL DESCRIPTION ...............................................................................................................................12

SPECIFICATIONS ...............................................................................................................................................14

APPENDIX A – TROUBLESHOOTING................................................................................................................15

APPENDIX B – HANDLING INSTRUCTIONS.....................................................................................................16

APPENDIX C – ELECTRICAL INTERFACE ........................................................................................................17

APPENDIX D – ASYNCHRONOUS COMMUNICATIONS ..................................................................................18

APPENDIX E – MECHANICAL DRAWING .........................................................................................................19

APPENDIX F – HOW TO GET ASSISTANCE .....................................................................................................20

APPENDIX G – COMPLIANCE NOTICES ..........................................................................................................21

WARRANTY ........................................................................................................................................................22

Introduction

The Sealevel COMM+8.422.PCIe (Item# 7802e) provides a PCI Express 1.0a compliant interface adapter

with eight asynchronous serial ports for industrial automation and control applications. The serial ports are

field selectable for RS-422 or RS-485 and support data rates to 921.6 Kbps.

RS-422 mode for is designed for long distance device connections up to 4000ft. where noise immunity and

high data integrity are essential. RS-485 mode can capture data from multiple peripherals in an RS485

multi-drop network. Up to 31 unit load RS-485 devices can be connected to each port to automate your data

collection. You can even mix the ports in any of the interface combinations to provide maximum flexibility

to your application.

In RS-485 mode, the transmitter is automatically enabled in hardware, eliminating the need for application

software control. This allows the 7802e to be used with standard serial communications applications and

removes the risk of bus contention and data corruption. The Sealevel SeaCOM software driver and utilities

make installation and operation easy XP, Vista, Windows 7, and Windows 8 operating systems.

The 7802e ships with a low profile PC bracket for use in systems with a low profile PCI Express slot. If you

need a standard size PC bracket, order the 7802eS.

Features

•PCI Express eight-port serial interface adapter

•Each port individually configurable for RS-422 or RS-485

•High performance OXPCIe954 UART with 128-byte FIFOs

•Each port supports data rates to 921.6K bps

•Oscillator and clock prescaler support wide range of baud rates

•Supports 9-bit protocol framing

•PCI Express 1.0a compliant via X1 connector

•Compatible with all low profile and standard size PCI Express slots

•Includes 36” cable that terminates to eight DB9M connectors

•Automatic RS-485 enable/disable

Before You Get Started

What’s Included

The COMM+8.422.PCIe is shipped with the following items. If any of these items are missing or damaged,

please contact Sealevel for replacement.

•COMM+8.422.PCIe Serial I/O Adapter – Four-Port 422/485 Serial Interface

•7802e – PCI Express Board with Low Profile PC Bracket

•7802eS – PCI Express Board with Standard Height PC Bracket

•CA231 – 68 pin Male to (8) DB9 Male Cable

Advisory Conventions

Warning

The highest level of importance used to stress a condition where damage could result to the

product, or the user could suffer serious injury.

Important

The middle level of importance used to highlight information that might not seem obvious or a

situation that could cause the product to fail.

Note

The lowest level of importance used to provide background information, additional tips, or other

non-critical facts that will not affect the use of the product.

Optional Items

Depending upon your application, you are likely to find one or more of the following items useful for

interfacing the COMM+8.422.PCIe to real-world signals. All items can be purchased from our website

(www.sealevel.com) or by calling (864) 843-4343.

Terminal Block Kit (Item# KT106)

Terminal Block Kit - TB06 + (2) CA127 Cables

Terminal Block Kit (Item# KT105)

Terminal Block Kit - TB05 + CA127 Cable

Terminal Block Kit (Item# TB34-8)

Terminal Block Kit (8 Pack) - DB9 Female to 5 Screw Terminals

(RS-422/485)

Hardware Description

PCI Express Board

The 7802e is a low profile PCI Express 1.0a compliant board via single lane x1 slot. It can be used in any

single- or multi-lane PCI Express slot. It is available in standard height PCI Express as item# 7802eS.

68Pin Board Connector

The board integrates a 68 pin female connector for interfacing the serial ports via the included cable.

DB9M Serial Connectors

The 7802e ships with an eight-port cable (Item# CA231) that includes eight DB9 male serial connectors.

The pin out for these connectors is detailed in the following Technical Description section.

Hardware Configuration

Address and IRQ selection

The COMM+8.422.PCIe is automatically assigned I/O addresses and IRQs by your motherboard BIOS or by

a ‘Plug-n-Play’ Operating System. Adding or removing other hardware or moving the adapter to another slot

may change the assignment of I/O addresses and IRQs.

Clock Modes

The COMM+8.422.PCIe derives a 62.5MHz clock from the PCI express link which is divided by a 8 bit clock

prescaler and a 16 bit clock divisor to provide a wide range of possible baud rates. Note that there are many

combinations that can give the same result (e.g. Prescaler=1 and Divisor = 8, Prescaler =2 and Divisor = 4,

or Prescaler=8 and Divisor = 1). As long as the calculated data rate is within +/- 2% you should communicate

fine.

Baud Rates

The following table shows some common data rates and the rates you should choose to achieve them

when using the COMM+8.422.PCIe.

For This Data Rate Clock Prescaler Choose This Divisor DLM:DLL

1200 bps 3.625 898

2400 bps 3.625 449

4800 bps 1.875 434

9600 bps 1.875 217

19.2K bps 1.375 148

38.4K bps 1.375 74

57.6K bps 22.625 3

115.2K bps 1 34

230.4K bps 1 17

460.8K bps 2.125 4

921.6K bps 2.125 2

Electrical Interface Selection

Each of the eight ports on the COMM+8.422.PCIe can be individually configured as an RS-422, or RS-485

interface. This is selectable via the port DIP-switch, each is labeled with its port number.

Switch 1 (Silk M1) Switch 2 (Silk M0) Mode Select

OFF OFF RESERVED

OFF ON 422

ON OFF 485 With Echo

ON ON 485 No Echo

Line Termination

Typically, each end of the RS-485 bus must have line-terminating resistors (RS-422 terminates at the receive

end only). A 120-ohm resistor is across each RS-422/485 input in addition to a 1K-ohm pull-up/pull-down

combination that biases the receiver inputs. Each switch allows customization of this interface to specific

requirements. Each switch position corresponds to a specific portion of the interface. If multiple

COMM+8.422.PCIe adapters are configured in an RS-485 network, only the boards on each end should have

switches T, P & P ON. Refer to the following table for each position’s operation:

Switch Name Function

3 T Adds or removes the 120 ohm termination.

4 PU Adds or removes the 1K ohm pull-up resistor in the RS-422/RS-485 receiver circuit

5 PD Adds or removes the 1K ohm pull-down resistor in the RS-422/RS-485 receiver circuit

6 L Connects the TX- to RX- for RS-485 two-wire operation.

7 L Connects the TX+ to RX+ for RS-485 two-wire operation.

RS-485 ‘ECHO’

In ‘RS-485 With Echo’ mode both the receiver and the transmitter are enabled simultaneously. Every time a

character is transmitted; it is also received. This can be beneficial if the software can handle echoing (i.e.

using received characters to throttle the transmitter) or it can confuse the system if the software does not.

An RS-485 ‘No Echo’ option is selected by placing both Mode switches (M0, M1) in the ‘On’ position.

Figure 1 - RS-422 Mode

Figure 2 - RS-485 2-wire with 'Echo'

Figure 3 - RS-485 2-wire, No 'Echo'

1234567

123456 7

Installation & Configuration

Windows Installation

Do not connect the hardware until the software has been fully installed.

Only users running Windows 7 or newer should utilize these instructions for accessing and

installing the appropriate driver via Sealevel’s website. If you are utilizing an operating system

prior to Windows 7, please contact Sealevel by calling 864.843.4343 or emailing

[email protected] to receive access to the proper driver download and installation

instructions.

1. Begin by locating, selecting, and installing the correct software from the Sealevel software

driver database.

2. Type in or select the part number (#7802e) for the adapter from the listing.

3. Select “Download Now” for SeaCOM for Windows.

4. The setup files will automatically detect the operating environment and install the proper

components. Follow the information presented on the screens that follow.

5. A screen may appear with text similar to: “The publisher cannot be determined due to the

problems below: Authenticode signature not found.” Please click the ‘Yes’ button and

proceed with the installation. This declaration simply means that the operating system is

not aware of the driver being loaded. It will not cause any harm to your system.

6. During setup, the user may specify installation directories and other preferred

configurations. This program also adds entries to the system registry that are necessary

for specifying the operating parameters for each driver. An uninstall option is also included

to remove all registry/INI file entries from the system.

7. The software is now installed, and you can proceed with the hardware installation.

Do not connect the hardware until the software has been successfully installed. To install Sealevel

software, you must log in as an administrator or have administrator privileges in Windows.

To install Sealevel software, you must log in as an administrator or have administrator privileges

in Windows.

Andere Handbücher für COMM+8.422.PCIe

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SeaLevel Computerhardware Handbücher

SeaLevel

SeaLevel ACB-ULTRA.LPCI Bedienungsanleitung

SeaLevel

SeaLevel SIO-104+2 Series Bedienungsanleitung

SeaLevel

SeaLevel LATCH-16 Bedienungsanleitung

SeaLevel

SeaLevel Relio Fanless Core 2 Duo R5200 Series Bedienungsanleitung

SeaLevel

SeaLevel Ultra COMM+2.PCIe 7205ec Bedienungsanleitung

SeaLevel

SeaLevel 3547 Bedienungsanleitung

SeaLevel

SeaLevel DIO-16.LPCIe Bedienungsanleitung

SeaLevel

SeaLevel Relio Fanless Core 2 Duo R5100 Series Bedienungsanleitung

SeaLevel

SeaLevel SeaLINK +2.SC Bedienungsanleitung

SeaLevel

SeaLevel ULTRA COMM+I.PCI 7103 Bedienungsanleitung

SeaLevel

SeaLevel COMM+2 Bedienungsanleitung

SeaLevel

SeaLevel ULTRA COMM+8.PCIe Bedienungsanleitung

SeaLevel

SeaLevel ISO-COMM Bedienungsanleitung

SeaLevel

SeaLevel SeaLINK+8/USB Bedienungsanleitung

SeaLevel

SeaLevel LATCH-16 Bedienungsanleitung

SeaLevel

SeaLevel VERSA COMM +4 Bedienungsanleitung

SeaLevel

SeaLevel UltraCOMM+2.LPCIe Bedienungsanleitung

SeaLevel

SeaLevel ROUTE 56 R Bedienungsanleitung

SeaLevel

SeaLevel DuoCom Bedienungsanleitung

SeaLevel

SeaLevel DIO-16.LCPI Bedienungsanleitung

SeaLevel

SeaLevel ULTRA 530.PCI Bedienungsanleitung

SeaLevel

SeaLevel ACB 56 Bedienungsanleitung

SeaLevel

SeaLevel eI/O-110 Series Bedienungsanleitung

SeaLevel

SeaLevel PC-SIO 3600-485 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung