Sealey WC06 Bedienungsanleitung

INSTRUCTIONS FOR

MOTORCYCLE WHEEL CHOCK

MODEL NO’S: WC06, WC07, WC08

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may

occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the

operator. It is the operators responsibility to secure the load. Check with vehicle manufacturer’s Manual before installing.

9Make sure the wheel of the equipment being mounted or dismounted is aligned with the chock.

9Inspect chock before each use. Check fasteners for tightness, replace any worn or damaged parts.

8DO NOT attempt to use a chock that is damaged in any way.

8DO NOT modify the chock in any way.

9Proper care and maintenance of the chock is critical to safety.

9Proper use of this product is critical to safety. Improper use may result in personal or property damage which is not covered by the

warranty.

2. i INTRODUCTION

Wheel chock supports the wheel of the motorcycle when in transit or storage. Made from black powder coated heavy-duty tubular steel with pre-

drilled holes and fixings which allow chock to be fixed to any suitable surface. A range of three sizes is available covering maximum tyre widths of

95mm, 140mm, and 165mm.

3. SPECIFICATION

Model Number Maximum Tyre Width

WC06 95mm

WC07 140mm

WC08 165mm

4. CONTENTS

Part Description Quantity Part Description Quantity

A Wheel Chock 1 E 1/4” x 5/8” Screws 2

B Spacer Mounting Plates 2 F 2” Screws 4

C Slotted Mounting Plates 2 G Washers 4

D Steel Threaded Studs 2 H Locking Nuts 4

WC06, WC07, WC08 | Issue 1 30/11/17

Original Language Version

Refer to

instruction

manual

Wear protective

gloves

5. ASSEMBLY

5.1. From the underside of the wheel chock place the Steel Threaded Studs (D) into the front holes. Secure in position from the top surface

 usingthe1/4”x5/8”screws(E),seeg.1.

5.1.1. Identifythephysicallocationforthexingsontheintendedmountingsurfaceandcheckforanyobstructions.Drilltherequiredholes

using a 1/4” drill.

5.1.2. SpacerMountingPlate(A)islaiddirectlyonthetopofthexingsurfaceandalignedwithxingholes,seeg.2.

5.1.3. PlaceSlottedMountingPlate(C)ontopofSpacerMountingPlate(A)andsecurewiththe2”screws(F)xedfromtheundersideusing

Washers (G) and Locking Nuts (H).

WARNING: Ensure that the round hole in the Slotted Mounting Plate (C) is nearest to the direction of loading of the wheel into the

 chock.Thiswillensurethatthechockissecuredwhenpushedforward.Ifadditionalxingisrequiredtoensuresafeoperationthere

 aretwofurtherpossiblexingholesateitherendoftheWheelChock.

Original Language Version

fig.1fig.2

WC06, WC07, WC08 | Issue 1 30/11/17

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sealey Motorradzubehör Handbücher

Sealey

Sealey PWH598 Series Bedienungsanleitung

Sealey

Sealey WORKSAFE SSP78.V2 Bedienungsanleitung

Sealey

Sealey MS065 Bedienungsanleitung

Sealey

Sealey LINK MONKEY Bedienungsanleitung

Sealey

Sealey WCT02 Bedienungsanleitung

Sealey

Sealey MCRS1 Bedienungsanleitung

Sealey

Sealey mc454 Bedienungsanleitung

Sealey

Sealey PWH615 Bedienungsanleitung

Sealey

Sealey MS162 Bedienungsanleitung

Sealey

Sealey PWH617 Bedienungsanleitung

Sealey

Sealey SWH199 Bedienungsanleitung

Sealey

Sealey PWH699R Bedienungsanleitung

Sealey

Sealey MS065.V2 Bedienungsanleitung

Sealey

Sealey FPS7.V2 Bedienungsanleitung

Sealey

Sealey MS080.V2 Bedienungsanleitung

Sealey

Sealey SMC3 Bedienungsanleitung

Sealey

Sealey MS062 Bedienungsanleitung

Sealey

Sealey RPS2KD Bedienungsanleitung

Sealey

Sealey FPS6 Bedienungsanleitung

Sealey

Sealey MS0630 Bedienungsanleitung

Sealey

Sealey TDMCHB Bedienungsanleitung

Sealey

Sealey Siegen Tools S01001.V3 Bedienungsanleitung

Sealey

Sealey VS1830.V2 Bedienungsanleitung

Sealey

Sealey MC401 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung