Sealey AK714.V2 Bedienungsanleitung

INSTRUCTIONS FOR:

BLIND BEARING PULLER SET - 5PC

MODEL No: AK714.V2

2. INTRODUCTION

1. SAFETY

3. CONTENTS

26mm - 32mm Attachment (Part No: AK714.V2-01)

20mm - 25mm Attachment (Part No: AK714.V2-02)

Slide hammer (Part No: AK714.V2-03)

15mm - 20mm Attachment (Part No: AK714.V2-04)

11mm - 15mm Attachment (Part No: AK714.V2-05)

WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations are

adhered to when using this product.

DO NOT use this product if damaged.

Maintain product in good and clean condition for best and safest performance.

If the vehicle to be worked on is raised, ensure that it is adequately supported with axle stands or ramps and chocks.

Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.

Wear suitable clothing to avoid snagging. Do not wear loose jewellery and tie back long hair.

Account for all tools and parts being used.

If working off the vehicle, secure the work piece in a vice or clamp it to a work bench.

DO NOT operate puller if you are tired or under the influence of alcohol, drugs or intoxicating medication.

 IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual, to

establish the current procedure and data. These instructions are provided as a guide only.

2.1. Introduction

Fully chromed carbon steel medium stroke slide hammer. 370mm Overall length with 1.4kg hammer. Bearing

extractor collets with internal capacity from 11 to 32mm. Supplied in carry-case.

Original Language Version AK714.V2 Issue No.1 06/11/09

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these

instructions and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

4. INSTRUCTIONS

4.1. Prior to use of the required

attachment, disassemble and

grease as shown in fig.1.

Reassemble the attachment.

4.2. Screw the attachment into the

shaft, as shown in fig.2. Tighten

the attachment using a wrench.

Note: Do not over tighten.

4.3. Ensure the attachment jaws

are completely closed and insert

the attachment into the inner

diameter of the bearing, fig.3.

4.4 Turn the handle clockwise to

open the attachment jaws to

grip the bearing. See fig.4.

4.5. Hold the bearing puller as shown

in fig.5, slide the hammer to the

bearing end of the shaft and

then forcefully pull the hammer

to the other end of the shaft.

4.6. Ensure the bearing is being

pulled out evenly, if not, remove

the puller attachment and, using

a soft faced mallet, tap the

bearing until it is seated evenly.

4.7. Repeat paragraphs 4.5 and 4.6

until the bearing has been

removed.

4.8. Turn the handle anticlockwise to

close the jaws in order to

release the bearing from the

attachment head. See fig.5.

Loosen

Grease

Attachment Head

Fig.1

Tighten

Fig.2

Bearing

Attachment Head

Fig.3

Attachment Head

Hammer

Open jaws

Fig.4

Attachment Head

Hammer Close Jaws

Fig.5

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

Original Language Version AK714.V2 Issue No.1 06/11/09

Inhaltsverzeichnis

Andere Sealey Elektrowerkzeuge Handbücher

Sealey

Sealey HS102.V2 Bedienungsanleitung

Sealey

Sealey AK6290 Bedienungsanleitung

Sealey

Sealey SB951.V6 Bedienungsanleitung

Sealey

Sealey STW101 Bedienungsanleitung

Sealey

Sealey SPR001 Bedienungsanleitung

Sealey

Sealey HS103K.V2 Bedienungsanleitung

Sealey

Sealey E540.V3 Bedienungsanleitung

Sealey

Sealey PS981.V2 Bedienungsanleitung

Sealey

Sealey AK716.V2 Bedienungsanleitung

Sealey

Sealey AB933.V2 Bedienungsanleitung

Sealey

Sealey STW806 Bedienungsanleitung

Sealey

Sealey SM2502 Bedienungsanleitung

Sealey

Sealey VS709 Bedienungsanleitung

Sealey

Sealey YK509F Bedienungsanleitung

Sealey

Sealey HS100CE.V3 Bedienungsanleitung

Sealey

Sealey SB973.V3 Bedienungsanleitung

Sealey

Sealey Power Tools SA651.V3 Bedienungsanleitung

Sealey

Sealey CP1440MH Bedienungsanleitung

Sealey

Sealey STW804 Bedienungsanleitung

Sealey

Sealey SSG8E.V3 Bedienungsanleitung

Sealey

Sealey SA203 Bedienungsanleitung

Sealey

Sealey AK629 Bedienungsanleitung

Sealey

Sealey CP3001.V2 Bedienungsanleitung

Sealey

Sealey CP1202 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch