Seamaid 501115 Bedienungsanleitung

You just bought the PAR56 lamp colour OR white from the SeaMAID range. Thank you for your trust.

Follow this guide and the online video for an easy and quick installation.

UNIVERSAL

PAR56 LAMP

PAR56WH references

501115 and 501139

PAR56RGB references

500682 and 500736

501399 and 501405

> Installation guide

With its universal size, the SeaMAID PAR56 lamp is installed without any particular work in

all niches of the market, replacing the traditional 300VA incandescent lamp.

PAR56 lamp Screw terminal 12 VAC Power

supply cable

1 2 3

Presentation of the product

> Installation

A step by step assistance

Recommendations

Precaution, for the existing niches, we recommend to change the support and the gasket for a

perfect sealing guarantee.

Be sure that the lamp(s) are connected with a safety isolating transformer with a power higher

by at least 20% to the total power of the installed projectors.

Using other types of transformer is prohibited.

To be synchronized in manual mode On/Off, the colour lamps must be connected to the same

electric power supply.

Always grease the back cup of the lamp, which is in contact with the gasket, when reassembling

and screwing.

Handle the lamps with care and on a clean cloth support.

> Installation / Replacement

A step by step assistance

1. Before any operation, turn off the ~12 V

power supply from the safety isolating

transformer

2. Remove the existing projector from its niche,

immerged in the pool and place it on the edge

taking care of protecting the front of the

installed lamp

3. Wipe the whole projector and the power

supply cable with a soft and dry cloth

4. Unscrew the gland to make the power supply

cable free

5. Unscrew the screws which maintain the sealing

support

6. Unscrew the connectors and take off the

existing lamp

7. Change the gasket

8. Install the new SeaMAID lamp taking care of

greasing the back cup in contact with the gasket

(silicon grease provided)

9. Re-screw the connectors of the power supply cable

10. Re-screw the sealing support tightening the

opposite screw by pair to distribute a balanced

force at any point of the lamp

11. Re-screw the gland blocking the power supply

cable

12. Replace the projector in its niche and wrap the

power supply cable around the back support

13. Turn on the power supply, the lamp lights

> Use

PAR56RGB 500682 and 501405 model, 16 programs with remote controller

The use of the remote controller requires a positioning face to the lamp at a maximum

distance of 10 meters, unfolded antenna. Metallic part close to the projector or a too

deep immersion (max 1 meter) may restrict the remote controller use at a very short

distance.

In this case, it is also possible to change programs using the on/off switch of the electric

supply power of the projector. A cut of the current of less than 2 seconds makes the

program change. After a cut of the current for over 10 seconds, switch on restarts from

the last program used

To control several lamps, it is possible to use a ~12V radio switch installed at the

output of the ~220V/12V toroidal transformer.

For its first use, the remote controller needs to be paired with the lamp(s) installed in

the pool.

Manual program including 11 static colours and 5 controlled atmospheres

with the provided remote controller.

Recommendations :

In all cases, refer to the

leaflet provided with the

product.

In case of difficulty during

the installation or use, it

is recommended to

watch the installation

video and to read the

FAQ on our website.

Buttons functions :

O > Off/On

S > Synchronization

C > Colour selection

P > Programs sélection

For the first remote controller use, it is necessary to pair it with the

projector

1. Insert the provided battery in the remote controller; press each

button and check that the red LED lights

2. From the general power supply, switch on the projector

3. Switch off the projector and count more than 20 seconds to

switch it on again

4. Make fast Off/On twice and switch on the projector

5. Press the buttons O et S together on the remote controller

6. The projector flashes several times and stays on, the pairing

process is confirmed.

Remote controller

PAR56RGB 500682 and 501405 model

> Use

PAR56RGB 500736 and 501399 model, 16 On/Off programs

Manual programs including 11 static colours and 5 controlled atmospheres

Recommendations :

In all cases, refer to the

leaflet provided with the

product.

In case of difficulty during

the installation or use, it

is recommended to

watch the installation

video and to read the

FAQ on our website.

The PAR56RGB On/Off lamp control is manual, using the on/off switch of the

projector power. A cut of the current of less than 2 seconds makes the program change.

After a cut of the current for over 10 seconds, switch on restarts from the last program

used.

For the first use, the lamp lights on the program 1 (all LED lit). Then you go to the 11

static colours, followed by 5 automatic programs.

It is as well possible to use a ~12V radio switch and install it on the ~220V/12V

safety isolating transformer output.

To be synchronized on the On/Off manual mode, the lamp must be connected to the

same power supply.

> Use

PAR56WH 501139 model, 3 intensities with remote controller

>The use of the remote controller requires a positioning face to the lamp at a

maximum distance of 10 meters, unfolded antenna. Metallic part close to the projector

or a too deep immersion (max 1 meter) may restrict the remote controller use at a very

short distance.

In this case, it is also possible to change programs using the on/off switch of the electric

supply power of the projector. A cut of the current of less than 2 seconds makes the

program change. After a cut of the current for over 10 seconds, switch on restarts from

the last program used

To control several lamps, it is possible to use a ~12V radio switch installed at the

output of ~220V/12V the toroidal transformer.

For its first use, the remote controller needs to be paired with the lamp(s) installed in

the pool.

Manual program including 3 controlled intensity levels

with the provided remote controller.

Recommendations :

In all cases, refer to the

leaflet provided with the

product.

In case of difficulty during

the installation or use, it

is recommended to

watch the installation

video and to read the

FAQ on our website.

Buttons functions :

O > Off/On

S > Synchronization

C > Colour selection

P > Programs selection

For the first remote controller use, it is necessary to pair it with the

projector

1. Insert the provided battery in the remote controller; press each

button and check that the red LED lights

2. From the general power supply, switch on the projector

3. Switch off the projector and count more than 20 seconds to

switch it on again

4. Make fast Off/On twice and switch on the projector

5. Press the buttons O et S together on the remote controller

6. The projector flashes several times and stays on, the pairing

process is confirmed.

> Remote controller

PAR56WH 501139 model

> Accessories

Find here the compatible and recommended accessories

Recommendations :

Discover the online SeaMAID

range products

In case of difficulty during

the installation or the

use, it is recommended

to watch the installation

video and read the FAQ

on our website.

SeaMAID low voltage radio switch:

To control 1 to 12 lamps, choose between the 1 and 4 channel

module to install on the ~12V projector(s) power supply

Model 500743

Model 500750

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Seamaid Schwimmbadbeleuchtung Handbücher

Seamaid

Seamaid LedInPool 500866 Programmierhandbuch

Seamaid

Seamaid 502778 Bedienungsanleitung

Seamaid

Seamaid 502778 Programmierhandbuch

Seamaid

Seamaid LEDINPOOL 502808 Bedienungsanleitung

Seamaid

Seamaid LedinPool 502860 Programmierhandbuch

Seamaid

Seamaid 501160 Bedienungsanleitung

Seamaid

Seamaid 500859 Programmierhandbuch

Seamaid

Seamaid LEDINPOOL 502815 Programmierhandbuch

Seamaid

Seamaid 502785 Programmierhandbuch

Seamaid

Seamaid LEDINPOOL Programmierhandbuch

Seamaid

Seamaid LEDINPOOL 502877 Programmierhandbuch

Beliebte Schwimmbadbeleuchtung Handbücher anderer Marken

BEGA

BEGA 88 913 Bedienungsanleitung

Wibre

Wibre 4.0171 Bedienungsanleitung

Pentair

Pentair INTELLIBRITE 5G Bedienungsanleitung

S.R.Smith

S.R.Smith poolLUX Plus pLX-PL60 Bedienungsanleitung

Pentair Pool Products

Pentair Pool Products FIBERworks 20100100 Bedienungsanleitung

GRE

GRE LAGP8 Handbuch

CONCORD

CONCORD PATHE G/R2-S2 Bedienungsanleitung

Pentair

Pentair MICROBRITE Bedienungsanleitung

Dot-Spot

Dot-Spot aq DS 50 Bedienungsanleitung

DMK

DMK UWR 200 Bedienungsanleitung

ACQUA SOURCE

ACQUA SOURCE WPLD-5R Bedienungsanleitung

OR STEEL light

OR STEEL light HIPPOCAMPE Bedienungsanleitung

ASTEL LIGHTING

ASTEL LIGHTING METEOR LSR0640 Bedienungsanleitung

emaux

emaux UL-S100 Bedienungsanleitung

Albixon

Albixon 18W/12V Bedienungsanleitung

emaux

emaux S100 Series Referenzhandbuch

iGuzzini

iGuzzini BH93 Bedienungsanleitung

Oase

Oase ProfiLux LED 350/01 Bedienungsanleitung