Seanix 42PSEA06 Bedienungsanleitung
Page 0 of 83
Page 1 of 83
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE
EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT
GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND
DISCLAIMS RELIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
Date：2006/06/20
Page 2 of 83
CONTENTS
1、SPECIFICATION
1-1 General Specification …................................................….....……........................………....…. 4
1-2 Feature Summary ........................... ...................... .............................……………...………….. 5
1-3 External Interface .......................... ...................... ...............................................................…. 6
1-4 User Interface …......................... ..................................….....……........................………....…. 12
1-5 External Mounting Requirements .......................................................……………...………….. 13
1-6 Environmental Requirements .............................. ...............................................................…. 13
2、Precautions and Notices
2-1 Precaution of assembly. ....................................................................................................... 13
2-2 Precaution of Operation....................................................................................................... 13
3、Operation
3-1 Operation of Remote Control Transmitter ...........................................................................… 14
3-2 Front panel controls .....................................................................................................……… 15
3-3 OSD MENU Description ..................................................................................................……. 16
4、Trouble Shooting Chart
4-1 PANEL Trouble shooting………………….........................................................................…… 20
4-2 Turn PDP on and Check .... .................... .................................................................................. 20
5、White-Balance Adjustment
5-1 Equipments list and prepare………………………………………………………………………… 25
5-2 Preparation and Adjustment process……………………………………………………………… 25
6、DDC program and test
6-1 The list of Instrument ………………………………………………………….. …………………… 27
6-2 Program and test process ……………………………………………...………..………………….. 27
7、Flash Update
7-1 The list of Instrument……………………………...………………………………………………….. 28
7-2 The Operation explaining Flash Update ……………..………...………………………………….. 28
8、Software Platform Reference TV application
8-1 Introduction …………………………………………………………………………………………... 31
8-2 The Phobos Reference TV application …………………………………………………………... 31
9、Block diagram & Explain
9-1 PDP Block diagram and functions…………………………………………….…….. ……………… 33
9-2 Image board block diagram and signal introduce/process……………………………………..… 34
10、Waveform of signal
10-1 Waveform of input signal…………………..….. ………..……. …..…. …. ………………..…… 37
10-2 Signal waveform in the Image board …..….. ………..……. …..…. ……. ………………..…… 40
Page 3 of 83
11、Check and Measure
11-1 Image board…………………..….. ……….. …. ……………..……... ……………………..…… 43
11-2 SIDE AV board……………….…..…..……..….. ………..…….. …. ……………………..…… 45
11-3 PDC board……………….…..…..……..….. ………..…….. . ……. ……………………..…… 45
12、Mechanical Introduction
12-1 PDP internal view..…..….. ………..………. ……..……….….. …. ……………..…… 46
12-2 Mechanical of cabinet front disassembly……. ……..……….….. …. ……………..…… 47
12-3 Disassembly and assembly..…..….. ………..……. ……. ……. …. ……………..…… 48
12-4 Block Wiring diagram..…..….. ………..……. ……. ……. ………… ……………..…… 56
13、PCB LAYOUT
13-1 Image board PCB LAYOUT.……………………………………………………………………….. 59
13-2 Key board PCB LAYOUT……………………..…..…..….. ………..…….. …. ……………..…… 59
13-3 Side AV board PCB LAYOUT………………..…..…..….. ………..…….. …. ……………..…… 59
13-3 PDC board PCB LAYOUT……………….…..…..….. ………..….. ….….. …. ……………..…… 59
14、Schematic diagram……………………………………………………...........................……………...… 61
Page 4 of 83
1、SPECIFICATION
1-1 General Specification
Item Specification
Screen size 42 inch plasma display panel
Aspect 16:9
Display pixels 1024 x 768
Effective display size 933.89mm x 532.22mm
Number of color 16.7 million colors（8 Bits）
Contrast Ratio 10000:1 (in dark room，NTSC)
Panel
Spec
Peak brightness 1100 cd/㎡（NTSC）
TV Tuning 1 Tuners, Air:2~69 channels Cable:2~135 channels
Sound system MTS+SAP
TV Mode
Color system ATSC / NTSC
Video RCA x 1 NTSC
AV1 ( S_Video/Video) S-Video1 x 1 NTSC Audio: L/R x 1
Video RCA x 1 NTSC
AV2 ( S_Video/Video) S-Video2 x 1 NTSC Audio: L/R x 1
480i
1080i
480P
Video Mode
AV3 / AV4
COMPONENT X 2
(YCbCr/YPbPr)
YCbCr/YPbPrx 2
720P
Audio: L/R x 2
Signal input Analog：D-Sub 15 pin
Plug and play DDC / 2B
Support Frequency FH:31KHz to 80KHz ，FV:50Hz to 85Hz
D-Sub Mode
VESA: 640 x 480
VESA: 800 x 600
VESA: 1024 x 768
VESA: 1280 x 1024
PC Mode
D-Sub Audio Earphone (3.5ø)
Signal input Digital：DVI-D 24 pin
Plug and play DDC / 2B
DVI Mode
720P
1080i
480P
DVI Mode
DVI Audio Earphone (3.5ø)
Power input sources AC 100-240V , 50/60Hz
Power Power consumption ≤450W
Operation Temperature + 0 °C ~ + 40 °C
Storage Temperature - 10 °C ~ + 50 °C
Environment
Humidity 10% -- 85%
Dimension Width x Height x Thickness 1038 x 726.5 x 240 (mm)
Net weight With Stand 34Kg
Accessory Remote Control Transmitter, Battery X 2, Power Cord, User’s Manual, RCA Cable,
D-SUB Cable, DVI Cable.
Page 5 of 83
1-2 Feature Summary
The following is the specification summary for the display:
z107 cm (42”) 16:9 Large Screen Flat Panel Plasma Display
zResolutions: 1024 (H) X 768(V) pixels, (1 pixel = 1 R, G, B cells)
z0.912 mm (H) X 0.693mm(V) pixel pitch.
zViewing Angle: 160° Vertically and Horizontally
zInternal TV Tuner, Air: 2~69 channels Cable: 2~135 channels
zTypical Maximum Contrast Ratio: 10000:1
zTypical Maximum Brightness: 1100 cd/m2
zATSC receiver, MPEG-2 decoder
zNTSC receiver, Video decoder
zDual Video, Dual S-Video
zDual Y Pb Pr (480i,480p,720p,1080i) HDTV Ready
zPC D-SUB 15Pin INPUT
zD-SUB analog video with rate 50Hz to 85 Hz vertical refresh rate and 31KHz to
80KHz horizontal frequency
zDVI-D Signal (TMDS) INPUT, Support HDTV, SDTV
zClosed Caption / V-chip
zComposite, S-Video, and component video receiver
zMIPS controller
zAuto Scan TV Channels
zField upgradable firmware
zUniversal Power Supply designed for worldwide application
zOperating power consumption less than 450 W
zStandby power consumption less than 1 W
Page 6 of 83
1-3 External interface
Most of these interfaces are located at the back-panel. There’s also a group of connectors located
on the side of this device for easier access. The following figures depict these A/V connectors.
Back Panel A/V Connectors
Side A/V Connectors
S-
V
ideo Video L R Earphone
AV2 Input
Page 7 of 83
1-3-1 Video/Audio Inputs
The following sections specify the video/audio inputs for 42PSEA06.
1-3-1-1 TV Antenna Interface
①. TV Antenna Connector
42PSEA06 shall provide a F-type cable connector with 75 ohms termination on its back
panel for reception of radio frequency signals.
②. TV Systems
42PSEA06 shall be capable of receiving the following broadcasting systems in the North
America region.
•Analog terrestrial and cable broadcasting in NTSC system and “M” sound system.
•All 18 formats specified for ATSC digital broadcasting
•Clear QAM digital cable broadcasting
③. TV Channel Coverage
The RF tuner shall be capable of covering 55.25 to 859.25 MHz and tuning to the following
channels:
•VHF: channel 2 through 13
•UHF: channel 14 through 69
•Mid band cable: A1 through A8, A through I
•Super band cable: J through W
•Hyper band cable: AA through ZZ, AAA, BBB
•Ultra band cable: channel 65 through 94, 100 through 125
④. Closed Caption
42PSEA06 shall support closed caption and text mode for both video and TV system. These
supports shall include channel ½ and field ½ selectable features.
⑤. V-Chip
42PSEA06 shall support MPAA grade for movie and TV Parental Guideline for TV. This
support shall include changeable password.
1-3-1-2 AV1
A standard definition (SD) analog video/audio source designated as AV1 shall be located on its
back panel. It comprises the following electrical connections. Only one of the two video inputs
shall be connected.
①. S-Video Input
42PSEA06 shall provide a 4-pin mini-DIN connector for connection to an external S-Video
source.
②. CVBS Video Input
42PSEA06 shall provide a RCA type receptacle for connection to an external CVBS source.
Page 8 of 83
③. Audio Inputs
42PSEA06 shall provide two RCA type receptacles for the stereo audio signal associated
with AV1 input.
1-3-1-3 AV2
A standard definition analog video/audio source designated as AV2 shall be located at the side
of 42PSEA06. It comprises the following electrical connections. Only one of the two video
inputs shall be connected.
①. S-Video Input
42PSEA06 shall provide a 4-pin mini-DIN connector for connection to an external S-Video
source.
②. CVBS Video Input
42PSEA06 shall provide a RCA type receptacle for connection to an external CVBS source.
③. Audio Inputs
42PSEA06 shall provide two RCA type receptacles for the stereo audio signal associated
with AV2 input.
1-3-1-4 AV3
A YPbPr/YcbCr type component video interface designated as AV3 shall be located on its back
panel. It comprises the following electrical connections.
①. Video Inputs
42PSEA06 shall provide three RCA type receptacles for connection to an external component
video source.
②. Audio Inputs
42PSEA06 shall provide two RCA type receptacles for the stereo audio signal associated
with Component1 input.
1-3-1-5 AV4
A YPbPr/YcbCr type component video interface designated as AV4 shall be located on its back
panel. It comprises the following electrical connections.
①. Video Inputs
42PSEA06 shall provide three RCA type receptacles for connection to an external component
video source.
②. Audio Inputs
42PSEA06 shall provide two RCA type receptacles for the stereo audio signal associated
with Component2 input.
Page 9 of 83
1-3-1-6 PC Input
42PSEA06 accommodates a VGA type computer connection as specified below.
①.Video Input connector
42PSEA06 shall provide a 15-pin D-Sub connector on its back panel for connection to a
VGA type video source. The VGA signal input on the display shall be capable of receiving
RGB analog video, H and V syncs, and DDC. The table below specifies pin-outs of this
connector.
Analog Connector Pin-outs
PIN MNEMONIC SIGNAL
1 RV Red Video
2 GV Green Video
3 BV Blue Video
4 NC None
5 GND Ground (DDC Return)
6 RG Red GND
7 GG Green GND
8 BG Blue GND
9 +5 V +5 V (from the PC)
10 SG Sync Ground
11 NC None
12 SDA DDC Data
13 HS Horizontal Sync
14 VS Vertical Sync
15 SCL DDC Clock
②. Audio Inputs
42PSEA06 shall provide a 3.5 mm jack for the stereo audio signal associated with VGA
input.
③. Input Formats
42PSEA06 shall support the following input format on its VGA input.
Horizontal Vertical
Mode Resolution Total Nominal
Frequency
(KHz)
Sync
Pola-rity
Nominal
Freq.
(Hz)
Sync
Pola-rity
Nominal
Pixel
Clock
(MHz)
VGA 640x480@60Hz 800 x 525 31.469 N 59.940 N 25.175
SVGA 800x600@60Hz 1056 x 628 37.879 P 60.317 P 40.000
XGA 1024x768@60Hz 1344x806 48.363 N 60.004 N 65.000
WXGA 1280x1028@60Hz 1688x1066 64 N 60 P 108
1
6
11 15
5
10
Inhaltsverzeichnis
