SecuControl FTL Bedienungsanleitung

FTL Test Blocks

Reference Handbook

FTL-reference-en v.181

All information provided in this document is the property of SECUCONTROL .

SECUCONTROL grants its customers or potential customers the right to download,

copy, store and print this document for the sole purpose of assisting them in the correct

application of the products mentioned in this document.

All other uses of this document are expressely prohibited.

Intellectual Property Notice

This publication contains proprietary information under protection of the following

(among others) patents: DE 10 2005 025 108, DE 10 2008 016 388, US 7,271,357

and US 7,884,597.

Contents Disclaimer

Although the information and recommendations in this document are presented in

good faith and believed to be correct as of publication date, SECUCONTROL makes

no representations as to the completeness or accuracy thereof. In no event shall

SECUCONTROL be responsible for damages of any nature resulting from the use of

or reliance upon the contents of this document.

Continuous Improvements

Products developed by SECUCONTROL are continuously improved. The information

in this document may, therefore, be out of date.

Please make sure you have the latest release of this document before proceeding by

checking its name and revision code. This information is printed on the front cover

of this document, underneath the title. The latest release of this document can be

downloaded from www.secucontrol.com/downloads. Alternatively, you may contact

SECUCONTROL at any of the addresses provided on the rear cover of this document.

Contents

1 Introduction 1

The FTL Test Block .............................. 1

Key Features ................................. 1

Applicable Models .............................. 1

Unpacking ................................... 1

Part Number and Manufacturing Date Location ............... 2

Safety Symbols ................................ 2

General Safety Instructions .......................... 2

2 Principle of Operation 3

Closed Circuit ................................. 3

Open Circuit .................................. 3

Signal Injection ................................ 3

3 Application 5

Schematic Symbols .............................. 5

Typical Connection Schematic ........................ 6

4 Installation 7

Panel Cutouts, Drilling Plans and Mounting ................. 7

Wiring ..................................... 9

5 Operation 11

6 Technical Speciﬁcations 13

Electrical ................................... 13

Mechanical .................................. 14

Dimensional Drawings ............................ 14

7 Models Available 17

Number of banana jacks ............................ 17

8 Accessories 19

Adapters for use with Insulated Banana Plugs ................ 19

Adapters for use with Wide Test Leads .................... 19

ii CONTENTS

Jumper Cable ................................. 20

Current Measurement Probe ......................... 20

FTL 19” Rack Plates ............................. 21

Covers for 19” FTL Rack Plate Cutouts ................... 22

9 Spare Parts 23

Disconnect Pins ................................ 23

Dust Covers .................................. 23

Fitting Set ................................... 23

10 Ordering Information 25

Part Numbers ................................. 25

Available Conﬁgurations ........................... 25

1 Introduction

The FTL Test Block

The FTL is a test block for interfacing substation devices (protection relays, fault

recorders, revenue meters, . . . ) to the voltage and current transformers and to other

equipment on the system side of a power grid.

The FTL Test Block uses Disconnect Pins to isolate the substation devices from the

system side equipment. Once isolated, secondary injection can be performed using

banana jacks on the front side of the Test Block.

Key Features

•Finger-safe Test Block and Disconnect Pins increase safety during testing.

•Disconnect Pins are keyed to the corresponding parts of the Test Blocks, pre-

venting mistakes and errors during test.

•Extremely low internal resistance (<2 mΩ) helps reduce heat inside cabinets

and panels.

•Available in 8, 10, 12, 14, 16, 18 or 20 pole conﬁgurations.

Applicable Models

Information in this document applies to all FTL Test Blocks manufactured after May

2011.

Unpacking

Unpack the product carefully and make sure that all pertinent parts like dust covers

and screws are put aside so they will not be lost.

Check the contents against the packing list. If any of the contents listed are missing,

please contact SECUCONTROL immediately (see contact information at the rear cover

of this manual).

1. INTRODUCTION

Examine the product for any shipping damage. If the product is damaged, notify

the shipping company without delay. Only the consignee (the person or company

receiving the unit) can ﬁle a claim against the carrier for shipping damage.

Part Number and Manufacturing Date Location

Part number and manufacturing date are stated on a label on the right side of the Test

Block.

Safety Symbols

The following symbols are located on different parts of the equipment and in this

manual:

Paragraphs marked with this symbol contain information which,

if not properly followed, may cause damage to the equipment

and/or installation.

Paragraphs marked with this symbol contain information which,

if not properly followed, may cause personal injury or even

death.

General Safety Instructions

Installation and operation of the products described in this manual is only to be per-

formed by personnel that has been trained or is knowledgeable in substation protec-

tion, automation and control.

This instruction manual is an integral part of the scope of delivery and provides basic

instructions for installation and operation of the equipment here described. Shall ad-

ditional information be needed, please contact SECUCONTROL at any of the addresses

provided on the rear cover of this document.

Do not disassemble the Test Block. Correct alignment of internal parts is critical in

order to provide insulation and arch-avoidance.

The warranty will be void if the Test Block is disassembled (or otherwise handled

inappropriately). SECUCONTROL does not assume responsibility for any damages

arising out of mishandling of our products, including test blocks that have been disas-

sembled by parties other than SecuControl.

2 Principle of Operation

Closed Circuit

In the resting state the contacts of the FTL Test Block are

closed. In this situation, the signals from the system side

of the installation (side A) are connected to the measuring

and protection devices (side B).

Open Circuit

To open the Test Block’s contacts, the disconnect pins are

moved from the parking position to the test position. In

this situation, the devices on the B-side are insulated from

the installation side.

Signal Injection

With the disconnect pins in the test position, signal injec-

tion can be performed using the banana jacks on the front

side of the Test Block.

3 Application

Schematic Symbols

Following symbols are suggested in order to represent the FTL Test Block in schematic

diagrams.

Symbol Description

Signal, Voltage (single pole)

- C

C - - C

- C -

C -

Current (2-pole, 4-pole)

3. APPLICATION

Typical Connection Schematic

V V V

C - - C C - - C C - - C

10 004 AA

Inhaltsverzeichnis

Andere SecuControl Prüfgeräte Handbücher

SecuControl

SecuControl ITS 4600 Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung