Securam ScanLogic Audit Bedienungsanleitung

SECURAM Systems Inc. Page 1

Part Number: FPC-0601A-M

．

Optical Fingerprint Reader

．

LCD Screen

．

Digital Pad

Document No.: S01A-FPC-0601A-M

Version No.: V1.01 USER

ScanLogic Audit Operating Instructions

SECURAM Systems Inc. Page 2

Important:

● For indoor use only.

● Use one 9V alkaline battery. Manufacturer recommends to use DuracellTM or

Energizer® Alkaline batteries.

Always use an alkaline battery for high quality performance.

● Battery Low Voltage: 5.4 ± 0.2V. The display will alert low battery when battery voltage

reaches 5.4±0.2V. PLEASE REPLACE THE BATTERY IMMEDIATELY.

Note: The voltage is checked during fingerprint verification. If the battery is low, nearing

5.4±0.2V, the EntryPad will not allow functions other than unlock. (Operations, such as

enrolling, deleting or time-delay setting, are not permitted until the battery is changed).

Security level classification

Level 1: EntryPad can be operated by a code.

Level 2: EntryPad must be operated by a fingerprint and its bound code.

Level 3: EntryPad must be operated by a fingerprint or a code.

Note: Factory default security level is Level 3.

For safety and security, all codes will be automatically deleted when security level is

changed. ID No. 01 code will be default code 1234567890.

As is the case with all biometric safe locks, the UL listing requires operation in Security

Level 2 only.

Battery Replacement Instructions

1) In the back of EntryPad you will see one 9 V alkaline battery. Take the battery out of the

battery compartment. Gently pull on the battery until it drops out.

2) Gently remove the connector by unsnapping it from the two terminals on the top of the

battery.

Never Pull on the Battery Leads.

3) Connect a new 9 V alkaline battery to the battery clip.

4) Put the battery and the leads completely back into the battery compartment.

For installation and wiring refer to the installation instructions.

About Default Codes:

The ScanLogic Audit has 1 default code 1234567890. However upon enrollment and use of

the first fingerprint (ID01), this default code is deleted. It is important to set a new code

relative to this fingerprint.

SECURAM Systems Inc. Page 3

Contents

1. Lock Set Up 4

2. Opening the Safe Lock System 4

3. Enrolling the first fingerprint 4

4. Open the Lock using an Enrolled Fingerprint 5

5. Enroll the second fingerprint 5

6. Enroll additional fingerprints 5

7. Set/Change User Code 6

8. Enable and Set User Code 6

9. Disable User Code 7

10. Disable User 7

11. Enable User 8

12. Set time delay 8

13. Time Delay - Unlock with an enrolled fingerprint 9

14. Time Delay - Unlock with a User Code 10

15. View Audit Trail 10

16. Set number of locks 10

16. Authorize access to locks 11

17. Delete One User 11

18. Delete All Users 12

19. Wrong entry penalty 12

20. Set Security Level 13

21. Enroll the first fingerprint and its bound code 13

22. Enroll the second or additional fingerprints and bound code 14

23. Set/Change the first code 14

24. Enroll the second or additional codes 14

25. Disable / Enable User 14

26. Set time delay 14

27. Unlock with an enrolled user 15

28. Set number of locks 15

29. Authorize access to locks 15

30. Delete one user / all users 15

31. Wrong entry penalty 15

32. System info. 15

33. Specifications 16

SECURAM Systems Inc. Page 4

1. Lock Set Up

 In the back of EntryPad, you’ll find a battery compartment. Install a brand new 9V

alkaline battery. It is recommended to use Duracell or Energizer standard alkaline

batteries.

2. Opening the Safe Lock System

The safe lock system is shipped in Security Level 3. This means that it can be opened with

either an enrolled fingerprint or a valid user code.

To open the safe lock using the default code, follow these steps:

 Press the button on the EntryPad above the word “Code” (It is the button marked “6 7

8”). This indicates to the safe lock system, that a valid code will be entered in order

to operate the safe lock.

 Now enter the default Administrator Code - which is 1234567890

o Important – The ScanLogic Audit has a Multi-Numeric EntryPad which means

that a single key on the EntryPad can represent more than one number. In

order to enter a “5”, press the button marked “345” just once. Likewise to

enter a “7”, press the button marked “678” just once.

 The lock opens; and after 6 seconds automatically relocks.

To open the lock with a fingerprint, a fingerprint must first be enrolled. See #3 below.

3. Enrolling the first fingerprint (Level 3: Fingerprint or Code)

 Place your finger on the Optical Fingerprint Reader.

 The LCD screen will show “Start Enrolling First User”.

 Hold your finger on the Optical Fingerprint reader through the following display

screens:

 This first fingerprint is now enrolled as User ID01. This Administrative (or Manager)

Fingerprint is used to access all programming including subsequent fingerprint

enrollment.

Note: The default password, 1234567890, will be deleted automatically after the first

fingerprint is enrolled and unlocked successfully. Be sure to set a code for User ID01 – See

#7- Set/Change User Code.

SECURAM Systems Inc. Page 5

4. Open the Lock using an Enrolled Fingerprint

To open the lock using an Enrolled Fingerprint follow these steps:

 Place your finger on the Optical Fingerprint Reader and hold.

 The LCD screen will display:

o “Verifying”

o “IDXX Verified” – indicating the ID number of this user

o “Door Open 06 seconds”

o The Lock can now be opened

5. Enroll the second fingerprint (Level 3)

 Unlock the safe lock system with the first enrolled fingerprint.

 After the successful verification, the screen will show “Select Menu”.

 Press “▲” or “▼” to scroll to “Enroll New User”.

Press “Menu/OK” again.

Place your finger (different from the first one) on the fingerprint reader

window and hold for the enrollment process to complete.

 The second fingerprint, with an ID No. 02, is now enrolled.

Note: ID No. 01 and ID No. 02 are administrators and can be used to perform programming

and to enroll additional fingerprints.

6. Enroll additional fingerprints (Level 3)

 Unlock the safe lock system with an administrator’s fingerprint (ID No. 01 or 02).

 After successful verification, the screen will show “Select Menu”.

 Press “▲” or “▼” to scroll to “Enroll New User”.

Press “Menu/OK” again.



Place another finger on the fingerprint reader window and hold for the

enrollment process to complete.

 The additional fingerprint is now enrolled as the next available User ID#

SECURAM Systems Inc. Page 6

7. Set/Change User Code (Level 3)

 Unlock the safe lock system with an administrator’s fingerprint (ID No. 01 or 02).



After successful verification, the screen will show “Select Menu”.

 Press “▲” or “▼”

to scroll to

“Set/Change User Code”

 Press “Menu/Ok”.

Enter a code (10 digits).

Enter the same code again.

 Now the new code is set or changed successfully.

Note:

● Administrators’ code can be set or changed using the method described above.

Non-administrators’ codes (ID03-ID30) must be enabled by the administrator first, then,

the user can set or change their own code.

8. Enable and Set User Code (Level 3)

This programming step is necessary to allow a User to have code access in addition to

fingerprint access.

 Unlock the system with an administrator’s fingerprint (ID No. 01 or 02).

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Enable User code”, press “Menu/Ok”.

Press “▲” or “▼” to select the ID No. to be enabled.

Press “Menu/Ok”

 In the example, the User ID No.3 code is enabled and is ready to be programmed.

To Program or “Set” the User Code:

 Unlock the safe lock system with the fingerprint of ID No.03.

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Set/Change User Code”.

SECURAM Systems Inc. Page 7

 Press “Menu/Ok”.

Enter a new code (10 digits).

Enter the same code again.

 The LCD will display ID:03 Code Saved.

 ID03 Code can now be used to unlock the safe lock system.

9. Disable User Code (Level 3)

This programming step is necessary to disable a User’s code access. It does not delete the

User’s enrolled fingerprint.

 Unlock the system with an administrator’s fingerprint (ID No. 01 or 02).

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Disable User Code”

 Press “Menu/Ok”.

Press “▲” or “▼” to select the user ID need to be disabled.

Press “Menu/Ok”

The code of ID No.3 is disabled.

Note: This function simply disables the user’s code. It does not disable or delete the

enrolled fingerprint associated with this ID#. To delete a fingerprint see #17 – Delete

User.

10. Disable User (Level 3)

This programming step is necessary to disable a User’s access rights both fingerprint and

code. It does not however delete the fingerprint or code but temporarily disables the

fingerprint and code. To delete a fingerprint see 17. Delete User

 Unlock the system with an administrator’s fingerprint (ID No. 01 or 02).

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Disable User”.

Press “▲” or “▼” to select the ID No. to disable (e.g. ID 03).

Press “Menu/OK”.

SECURAM Systems Inc. Page 8

Both the code and fingerprint enrolled as ID03 are now disabled.

Note: Administrators cannot be disabled.

11. Enable User (Level 3)

This programming step is necessary to enable a User’s access rights - both fingerprint and

code. This step would be performed after a User has been “Disabled” – See #9 Disable User.

 Unlock the system with an administrator’s fingerprint (ID No. 01 or 02).

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Enable User”.

Press “Menu/OK”.

Press “▲” or “▼” to select the ID No. to enable (e.g. ID 03).

Press “Menu/OK”.

Now the No. 03 user is enabled.

12. Set time delay (Level 3)

Time Delay is security protocol used to deter burglary. Provided the prospective burglar has

knowledge that a Time delay safe is in use, the likelihood of burglary is greatly reduced.

Time Delay is a feature that requires the User present an enrolled fingerprint or enter a valid

code, wait a prescribed period of time, and then present an enrolled fingerprint or enter a valid

user code again to gain access.

 Unlock the system with an administrator’s fingerprint (ID No. 01 or 02).

 The LCD will display “Select Menu”

 Press “▲” or “▼” to scroll to “Set/Cancel Time Delay”.

Press “Menu/OK”.

Press “▲” or “▼” to set time delay (00 to 99 min).

Press “Menu/OK”.

SECURAM Systems Inc. Page 9

The system will now prompt you to enter the Time Window value (in minutes)

Press “▲” or “▼” to select Time Window (01 to 15 min).

Press “Menu/OK”.

The Time Delay feature has now been set successfully.

Notes related to Time Delay operations:

 During Time Delay period, programming operations (such as enrolling, deleting users

etc.) can be accomplished. The lock however will remain locked.

 Time Delay Override: User ID01 and 02 are Time Delay Override Codes. These

codes can be used to override the time delay and gain access immediately.

 After the original time delay is re-programmed, the new time delay setting will go into

effect after the first successful unlock cycle.

13. Time Delay - Unlock with an enrolled fingerprint (Level 3)

In order to unlock a safe lock that has been programmed with Time Delay, follow these

steps:

 Place an enrolled finger on the fingerprint reader to verify.

 The fingerprint will be verified and then the LCD will display “Time Delay Start”

For example:

Time Delay is set 10 minutes and Time Window 5 minutes.

 Place an enrolled finger (ID: 03) on the fingerprint reader window and hold until

the LCD shows:

 The EntryPad will start counting up.

 The LCD screen flashes with the elapsed time every 15 seconds.

 When Time Delay finishes counting, two beeps will sound and the LCD screen will

show:

 The EntryPad will start counting down.

 The LCD screen flashes with remaining time every 15 seconds.

 Since the Time Window has been set as 5 minutes in this example, a valid

fingerprint or code must be presented during the 5 minute Time Window to unlock

SECURAM Systems Inc. Page 10

the EntryPad.

 The LCD will display:

 If an enrolled fingerprint is not presented and verified during the Time Window

period, the safe lock will remain locked. The Time Window will continue to

countdown and until the end, and then the LCD will show:

Note:

User ID01 and 02 are Time Delay Overide (TDO) codes. This means that these Users

can bypass or override any Time Delay settings, and the lock will open immediately..

14. Time Delay - Unlock with a User Code (Level 3)

Follow the same procedure as above, but instead of presenting an enrolled fingerprint

enter a valid User code. Remember to press the button marked “Code” to indicate that

you will be entering a code

15. To View the Audit Trail

 Open the lock using the Admin fingerprint

 When “Select Menu” appears,

press “▲” or “▼” to “Show Audit Trail”



Press “Menu/OK”.



You can now view all 500 time/date stamped audit events on screen by scrolling

through the evenings using the Up or Down buttons.

15. Set number of locks (Level 3)

Unlock with an administrator’s fingerprint (ID No. 01 or 02).When the LCD shows “Select

Menu”, press “▲” or “▼” to select “Set number of locks”.

Press “Menu/OK”.

Enter Mfc. code. 9316961396

Press “▲” or “▼” to set number of locks.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Securam Sicherheitssystem Handbücher

Securam

Securam ScanLogic Optical Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung