SECURECOM SC-GSM Bedienungsanleitung

SC-GSM Alarm Signaling Communicator v1.3 1 EN

C-

-G

Analog phone line simulator (GSM gateway) or translation of

Contact ID signals to SMS messages and alarm calls.

One device with 2 independent operating modes.

Manual v1.3

SC-GSM Alarm Signaling Communicator v1.3 2 EN

Table of Contents

1 Short functional description of device .................................................................................................. 3

1.1 Main features ............................................................................................................................. 3

1.2 Technical specifications .............................................................................................................. 3

2 Product Layout ...................................................................................................................................... 4

3 Connection ............................................................................................................................................ 5

3.1 Power supply .............................................................................................................................. 5

3.2 Emulated phone line .................................................................................................................. 5

3.3 Trigger inputs .............................................................................................................................. 5

4 Configuration of device ......................................................................................................................... 6

4.1 Setup program connection ......................................................................................................... 6

4.2 Moving data between the PC and the device ............................................................................ 7

4.3 Device code lock (protection) ..................................................................................................... 7

4.4 Device Status .............................................................................................................................. 7

4.5 General setting ........................................................................................................................... 8

4.6 Transparent mode ...................................................................................................................... 8

4.7 Standalone mode ....................................................................................................................... 9

4.7.1 Setting the signaling in standalone mode ........................................................................ 10

4.7.2 The Contact ID codes comparation .................................................................................. 10

4.7.3 The reporting procedure .................................................................................................. 11

5 LED signals ........................................................................................................................................... 12

6 Most frequently used Contact ID codes .............................................................................................. 12

SC-GSM Alarm Signaling Communicator v1.3 3 EN

1 Short functional description of device

In Standalone mode the unit behaves like a monitoring station receiver which receives and handles

the CONTACT ID communication of alarm control devices. It compares the report codes with the filled

in event codes of the program table and at the occurrence of the desired event it sends the assigned

SMS message and initiates a call (siren sound is played). By this means the users of the alarm control

panel can be notified of any signals, differed by the event and subject of event (user, zone, partition).

Notifications are not limited to differ only few kind of events as it is usual with all other GSM (SMS)

communicators, with trigger inputs only. The best describing definition for this feature would be:

Converting Contact ID messages to programmable SMS messages and phone call notifications

Further function is that by controlling the contact inputs the communicator sends the assigned SMS

messages and calls the pre-set telephone numbers.

In transparent mode fully replaces phone line. By this means the alarm control panel can send the

report codes to monitoring station, or a simple phone device can be used on places where the phone

line is not available (elevators, SOS or INFO call points, weekend houses,…)

By controlling the contact inputs the communicator immediately sends the CONTACT ID messages

assigned to the inputs to the given monitoring station number and this way shorting down the

signaling time of the alarm state to monitoring station, providing more precious time to react, while

complete communication to monitoring station with full information of events in progress can take its

time.

1.1 Main features



2 separate modes of operation in one device



PSTN line simulation for monitoring station signal transmission



SMS/CALL about 32 different kinds of CONTACT ID reports



Signals to 4 telephone numbers



2 contact inputs with independent signals SMS/CALL



Handling SIM PIN code



Forwarding SMS



Setting and diagnostics via USB connection

1.2 Technical specifications



Power 9-30V (DC)

Power consumption

300mA (max.) / 100mA (idle)



Telephone line data

Line voltage 48V

Loop current 25mA

Load impedance 100-470 Ohm

Dial tone 425Hz



Operating temperature 0…+70°C



Size 40x75x15mm

SC-GSM Alarm Signaling Communicator v1.3 4 EN

2 Product Layout

Sign

Part Description

ANTENNA CONNECTOR

GSM network antenna

Connector type: SMA, Impedance: 50 ohm, Frequency: 900/1800 MHz

SIM CARD HOLDER

For mobile network connection

Type: GSM voice band card, Dimension: 2FF mini SIM

LED status display

The LED status signals

USB CONNECTOR

For parameters setting, the communicator must be connected to the

computer through USB port. Type: USB mini-B

DC POWER (

12V/COM

)

Main power supply

Rated voltage: DC 9-30V, Rated current: max. 500mA

Communication line

(TIP/RING)

Simulated landline for the alarm control panel’s TIP/RING input

Line voltage: 48V, Loop current: 25mA, Impedance: 300ohm

INPUT

S (Z1, Z2

)

Contact Input (to negative supply “COM” ) for transmission of the signal

of external switches

SC-GSM Alarm Signaling Communicator v1.3 5 EN

3 Connection

In order to operate properly, the device must be equipped with a valid SIM card and the external

antenna must be connected to the antenna connector. Use the supplied antenna or any other GSM

antenna that suites the needs for installation. The SIM card should be inserted to the card holder

“door” (the moving part of card holder), as shown on picture. The Door must be pushed toward the

PCB until completely “closed”, i.e. the two parts of card holder are overlapping, and after that the card

holder should be LOCKED, by puling the holder ”door” toward the terminals (as marked on the holder).

The locking of card holder gives a click sound. If the card was not placed properly as it should be, the

card holder door can not be locked and turning the PCB in horizontal position with card holder toward

the ground will cause the holder to open. In this case, the device will not operate properly, and may

cause the damaging of SIM card. Please be sure that the SIM card is placed properly before powering

up the device.

Warning: The SIM card should never be removed or added while the device is powered up.

3.1 Power supply

SC-GSM communicators can be powered from USB connection for programming only (downloading of

settings). For normal operation required the external power (connected to terminals +12V and COM).

The device will be functional with any power voltage between 9 and 30 V DC is applied to the

terminals.

3.2 Emulated phone line

The TIP and RING terminals of the SC-GSM device provides an emulated phone line. Connect these

terminals where the PSTN (regular phone line) is supposed to be connected to the device that will use

this communicator. In case of connecting to alarm panel, use the INCOMMING LINE terminals, (usually

marked with TIP/RING or T/R, or Ti/Ri...).

3.3 Trigger inputs

There are 2 CONTACT inputs on device, marked as Z1 and Z2. These inputs are used to trigger a voice

call to a user, send a SMS message, or to send a specified Contact ID code to a monitoring station

(when device is set to transparent mode). These inputs are triggered when connected to the COM, i.e.

to the supply negative line. When connecting the device to an alarm panel, if the power is supplied

from alarm panel (connected to its AUX terminals) these inputs can be directly connected to PGM

outputs of alarm panel, that are “open collector” type, since when activated, these outputs provide a

shortcut to the panel ground. With such connection, no other wiring is required. If the PGM is REELAY

type (two connection points), than one pole of the output relay must be connected to the same place

with the communicator COM terminal, and the other to Z1 or Z2, in balance with programming.

SC-GSM Alarm Signaling Communicator v1.3 6 EN

4 Configuration of device

Connect the device with USB cable to a windows PC (Compatibility: Windows 7, 8.1, and 10), and a

new drive will be installed. When connected to that machine for first time, the driver will be installed

first, then the new drive will be found. This drive is the flash memory of SC-GSM device, and contains

the software and this manual. You can run the software from device, or copy it to your PC and run it

from there. When the device is powered through terminals, the USB cable can be plugged or

unplugged at any time, it will not affect the device. The windows machine might require a proper

closing of USB connection before unplugging the cable.

4.1 Setup program connection

If the device is password protected or a wrong type of device is connected on USB port, the

PASSWORD field is displayed. If a wrong password is entered, the software will display the status fields

only Settings are not displayed and can not be changed. This mechanism prevents unauthorized access

to device settings.

As the software successfully connects to the device, it reads out the device and shows the status,

device version and actual settings in device (marked red on following picture):

In case that software does not show a “connected” status or the firmware version, the USB connection

was not made properly. Please select a different USB port check the USB cable. If the problem persist,

the device USB driver might be in conflict with some other driver in windows, restart the windows or

try the connection on another machine.

SC-GSM Alarm Signaling Communicator v1.3 7 EN

4.2 Moving data between the PC and the device

Reading out data from the device happens automatically as soon as connection is established. Settings

can be saved to PC or loaded from PC file. These icons are used to handle the settings data:

(File_reading / File_saving / Download to device )

IMPORTANT NOTICE: if a new settings file is loaded or ANY setting is modified on software screen, all

data needs to be downloaded onto the device. You can make all required changes in software, and then

download data. Changes that were not downloaded will be terminated when the software is closed or

the connection is cut (cable unplugged).

4.3 Device code lock (protection)

The device can be locked with a security code. By default, there is no code but once entered, the code

will be required for each connection. After connecting, the new code can be entered with the icon:

After connecting via USB, if the device was set with a code, the software requests to enter

the device code. If you cancel the code entry, the software will display only the status and no settings

can be red or edited. After closing re-starting the software, the code entry box is displayed again. Only

after the right code was entered, the software will be fully functional, presenting the whole window

with all settings displayed and editable.

WARNING: If the password is lost or forgotten, only way to access to device setting is with FACTORY

DEFAULT. For that procedure, the device must be sent to appropriate service

4.4 Device Status

The left side of the software window is showing the device status. This part is ALWAYS VISIBLE, even

when the device is protected with code lock. These are the fields in the status view:

Field name Options (description)

SIM status Waiting (connecting...) / OK / PIN request

GSM signal A value between 0 and 31, (12-16 is minimal for reliable functionality)

Line state ONHOOK / OFFHOOK (emulated phone line idle / active)

Z1 input state IDLE / ACTIVE (Input Z1 idle / active)

Z2 input state IDLE / ACTIVE (Input Z2 idle / active)

Communicational event messages:

Dialed The number dialled by the alarm control panel

CID The CONTACT ID code sequence sent by the alarm control panel

Z1 Event Activated input one

Z1 Restore Input one got back to default

SMS sending Sends the SMS messages belonging to the event

CALL(1) Calls the first set number

DTMF recd. got DTMF code, that is acknowledgement from the notified number

USB Status of USB connection (Connected or Disconnected)

SC-GSM Alarm Signaling Communicator v1.3 8 EN

4.5 General setting

The General setting parameters are valid for both operating modes, and in this area the operating

mode (transparent or standalone) is selected

4.6 Transparent mode

In this mode, device can be used as a transparent GSM Gateway, to forward voice signals (DTMF or

speech) from a phone device or alarm panel through a GSM network, to called party or a monitoring

station receiver. The phone device (alarm panel) connected to the RING/TIP terminals make the

dialing, the SC-GSM device just dials that number, and opens the VOICE channel to transfer all sounds

in high quality through GSM network. In case of incoming call, the device will ringing, the connected

phone device or alarm panel.

Operating mode TRANSPARENT operating mode (chapter 3.6)

STANDALONE operating mode (chapter 3.7 )

PIN code PIN code of the SIM card must be entered here if the card is set to request a

PIN. If a wrong PIN is entered, the device will „lock” the PIN card by trying to

activate the SIM with entered code, over and over. After 3 unsuccessfull PIN

code entries, the SIM requires a PUK code. This code must be entered with a

different device (mobile phone)

Incomming SMS notice Incomming SMS messages will be forwarded to the given telephone number

Z1 input setting the sensitivity and type of contact input Z1

Z2 input setting the sensitivity and type of contact input Z2

(Next fields available in Standalone mode ONLY)

Phone numbers User phone numbers where the unit can send the signal in the form of SMS

and/or call (to maximum 4 numbers).

ACK If the ACK field is selected next to a number, the device requests an

acknowledge signal for every call made to this number. Acknowledge signal is

any DTMF signal (any number from telephone keypad). If the acknowledge is

not received, the call is repeated until the acknowledge is made, but maximum

3 times. If the Acknowledge is received, all further calls for that event are

terminated. This means that the called party, who acknowledges the call, will

STOP the calls to numbers that are next in order (T1/T4).

SC-GSM Alarm Signaling Communicator v1.3 9 EN

Z1 and Z2 contact inputs are used as inputs of independent alarm communicator, triggering them

causes the sending of programmed event code (Contact ID protocol) to the programmed Receiver

Phone Number, paired with the programmed Account Id.

The partition number in the message is 01 and the value of the zone in the message is 001 and 002 and

they cannot be changed. Communication format is CONTACT ID. You can find the requested Contact ID

code in the Chapter 6, or the “Contact-ID-codes-with-explanation.PDF” file.

The best example of usage of these inputs is when the SC-GSM is used with alarm panel, to send a

QUICK signal of an alarm state, while the dialer in alarm panel slowly makes the complete reporting of

complete events through the emulated phone line. To achieve this, it is enough to connect a PGM or

BELL output from alarm panel to a zone input, along with ring/tip lines and the AUX (power supply)

wires.

4.7 Standalone mode

This mode is used to send notifications and informations from alarm panel directly to USERS. When

the alarm panel transmits a selected Contact ID event Code (through emulated phone line on ring/tip

terminals), SC-GSM device simulates a monitoring receiver, accepts the code and confirms the event

reception to alarm panel. After that, the received Code is compared to all codes set in the „Alarm

Event Handling”, and if it exists in the tabble, the communicator makes the programmed procedure-

starts a voice call or sends SMS messages to selected user numbers (1-4). The two inputs do the set

procedure same way, but activated with an external triger (contact).

In this mode the device expects to receive signal in the format defined by the CONTACT ID standard.

The Contact ID Message is defined this way:

SUBSCRIBER ID

XXXX

EVENT QUALIFIER

Event or Restore

EVENT CODE

XXX

PARTITION

ZONE or USER

XXX

8556 1 401 01 001

SC-GSM Alarm Signaling Communicator v1.3 10 EN

In the example , the received Contact ID code /8556 18 1 401 01 001/ means that a system with ID

number (“account number”) 8556, has sent a signal that EVENT (1) of ARMING (401) was made in

Partition 01, by user 001. With settings as shown on picture on top of this page, Appropriate SMS

message for this code ,”ANGIE left home” (Angie is user 001), will be sent to sent to T1 telephone

number.

Another example: When the alarm occurs in zone 2 of the alarm system, the code 8556 18 1 130

01 002 will be transmitted, and the SC-GSM device will be sending the “Burglary in the Hall!” SMS

message to required two phone numbers and starting call the phone numbers T1 (01234567891) and

expect the ACKNOWLEDGE from the called party (any button on dialer pressed) will be expected. If the

T1 number is not acknowledged, the communicator calling the next phone number T2 ( 01234567892).

4.7.1 Setting the signaling in standalone mode

Each line of the table should be set like this:

Code

E/R

Part

Zone /

User

C1,C2,C3,C4

MS message

S1,S2,S3,S4

CID code

(3 digit)

E: event

R: restore

Partition

Code

(2 digit)

Zone or U

ser

code

(3 digit)

Telephone

numbers (T1-

T4) designated

to voice call

SMS message

to be sent if a

code occurs

Telephone

numbers (T1-

T4) designated

to SMS

sending

If the received Contact ID Code fits the setting in one line of the table, the SC-GSM will perform the

procedure of calls and messages as set in that line. Each line is independent from another. You can use

the same Code in several lines, if any of other “filters” that are used for the received code comparation

(E/R, Part, Zone/User) differ from each other.

4.7.2 The Contact ID codes comparation

Code: Contact ID code that should be received in the Contact ID message from alarm panel, in

order to make the procedure that is defined in same line of the table. You can find the

requested Contact-ID code in the Chapter 6, or the “Contact-ID-codes-with-

explanation.PDF” file.

E/R: Event or restore of the event defined by the code, along with the CODE it presents the

event that is being transmitted. For example 1-130 is Event for Burglary alarm, and the 3-

130 is RESTORE of Alarm state (zone closed or system disarmed). Also 1-401 means

ARMING, while 3-401 means DISARMING.

Andere Handbücher für SC-GSM

Inhaltsverzeichnis

Andere SECURECOM Tor Handbücher

SECURECOM

SECURECOM SC-GSM Betriebsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung