SECURICO VENUS Bedienungsanleitung

User Manual

VENUS

Manufacturers of World Class Security, Fire & Automation Systems

www.securicoelectronics.com

FIRE ALARM SYSTEMS

STAND ALONE PIR MOTION SENSORS

GUARD MONITORING SYSTEMS

WIRED INTRUDER ALARM SYSTEMS

WIRELESS INTRUDER ALARM SYSTEMS

HYBRID INTRUDER ALARM SYSTEMS

AUTOMATION & IP SYSTEMS

VIDEO DOOR PHONES

PRODUCT RANGE:

- 1 -

ARMED MODE

The system is in the armed mode when all active* zones are

operational and can bring the system into alarm state.

*certain zones can be temporarily omitted from the system. See

section2-6.

Therearefourtypesofzonesinthecontrolpanel:

ENTRY/EXIT:An entry/exit zone will actively raise an alarm only if the

systemisArmed.However,anentry/exitzoneallowsforaprogrammed

delayduringwhichthe user canenterthecodeand prevent alarmfrom

sounding. If the user does not enter the code in the programmed

amount of time, the alarm will sound. The main entry is usually the

entry/exit zone so as to allow the user to enter the premises without

raisingthealarm.Entry/Exitzonesarealsoreferredtoasdelayzones.

IMMEDIATE:An immediate zone will actively raise an alarm only if the

system is armed. If anyone enters the premises through an immediate

zone while the system is Armed, the alarm will sound immediately.

Immediate zones usually include all the doors and windows other than

the main entry, since the user is unlikely to enter the premises through

these.

PANIC:APaniczoneisa24hourzoneandwillraiseanalarmwhenthe

panic switch is pressed irrespective of whether the system is armed or

disarmed.

1-2 ZONES

FIRE :AFire zone isa24hourzoneandwillraise an alarm in caseafireis

detectedirrespectiveofwhetherthesystemisarmedordisarmed.

In the case of an alarm, the sounders will be activated and the automatic

speech dialer will call all programmed numbers and play the

correspondingemergencymessages.

1-3 FACTORY SETTINGS

1. The MASTER CODE is set to 1234

The SERVANT CODE is set to 5678

2. ZONE 1 is set as the entry/exit zone

ZONE 2 is set as the immediate zone

ZONE 3 is set as PANIC zone

ZONE 4 is set as FIRE zone

3. The ENTRY/EXIT delay is set to 30 seconds

4The SOUNDER TIME is set to 2 minutes

- 2 -

Allzoneswillbearmedandthe ARMEDLEDwillglow.

The immediate zones must be closed before arming the system. If any

active immediate zones is open, the corresponding LED will flash along

with an audio indication. The entry/exit zone must be closed within the

entry/exitdelaytime.

This unique feature allows us to temporarily make all entry/exit (delay)

zones into immediate zones. When the system is armed at night and all

users are within the premises, the entry/exit time is not required. This

featureisparticularlyhelpfulwhenthesystemisinstalledinaresidence.

- PressENTER

- PressARM

- PressHELP

All zones will be armed and all delay zones will temporarily become

immediatezones

If arming sound is not required, it can be silenced. The system will arm

itselfsilentlyendingwithabeeptoindicatethatthesystemisarmed.

Press ENTER

Press ARM

- 3 -

IMPORTANT NOTE : If the system is in alarm state, the master code has

to be entered twice. The first time will switch off the sounders. The second

time will stop the automatic speech dialer. If you wish to stop the sounder

but want the speech dialer to continue dialing the programmed numbers,

enterthecodeonlyonce.

- PressENTER

- PressARM

- Press0

EnterMASTERCODE todisarmthewholesystem.

EnterSERVANTCODEtodisarm zonesallocatedtotheservants.

(PleaseseeFactorySettingsinSection1-3)

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressCODE

- PressPROG

- PressMASTtochangeMASTERCODEOR

- PressSERVtochangeSERVANT CODE

- PressPROG

- Enternew4digitcodeXXXX

- Thesystemwillsoundfourbeeps

- Repeatandconfirmnew4digitcodeXXXX

- PanelreturnstoDAYMODE

- 4 -

*If the two codes entered do not match, the system will sound fast error

beepsandreturntodaymode.Thepreviouscodewillberetained.

(PleaseseeFactorySettingsinSection1-3)

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressDELAY

- PressPROG

- EnternewEntry/Exitdelay(2to255seconds)

- PressENTER

- SystemreturnstoDAYMODE

If the time entered is not within the specified time range, the system will

sound fast error beeps and return to day mode. The previous Entry/Exit

delaywillberetained.

(PleaseseeFactorySettingsinSection1-3)

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressSNDR

- PressPROG

- EnternewSoundertime(2to20minutes)

- PressENTER

- SystemreturnstoDAYMODE

- 5 -

*If the time entered is not within the specified time range, the system will

sound fast error beeps and return to day mode. The previous Sounder

delaywillberetained.

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressZONE

- PressPROG

- PressMASTtoomitmasterzones

- PressPROG

- ZoneLEDswillglow

- Enter the zone numbers you wish to omit and the corresponding

LEDs will SWITCH OFF (LEDs will toggle ON and OFF if a

number is entered more than once. If a zone LED is OFF, the

zonewillbeomitted)

- PressENTER

- SystemreturnstoDAYMODE

IMPORTANTNOTE: Asa safetyfeature,once thesystemisdisarmed,all

master zones will automatically be re-activated. The above procedure

must be followed each time you wish to part set the system and omit

certainmasterzones.

- EnterMASTERCODE

-PROGRAMLEDwillblink

-6 -

- PressPROG

-PROGRAMLEDwillglow

- PressZONE

- PressPROG

- PressSERVto changeSERVANTZONES

- PressPROG

- ZoneLEDswillglow

- Enter the zone numbers you wish to allocate to the servants and

the corresponding LEDs will SWITCH ON. (LEDs will toggle on

theoffifanumberisenteredmorethanonce.IfazoneLEDison,

thezonewillbeincludedintheservantzones)

- PressENTER

- SystemreturnstoDAYMODE

IMPORTANT NOTE : Servant zones once programmed will remain al

allocated till re-programmed using the above procedure. Only one

category, Master or Servant zones can be programmed at a time. To

program/re-programanyzonestatus,theproceduremustberepeated.

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillblink

- PressLOG

- PressPROG

- TheZoneLEDofthelastzoneinwhichtherewasanintrusionwill

glow

- PressENTERtoseethePREVIOUSZONE

- Ifalongbeepisheard,thelogisempty orfinished

- PressEXITtoreturntoDAYMODE

- 7 -

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressREC

- PressPROG

- Press1torecordIntrusionMessage2ortorecordfiremessage

- The recording will start and you must record the message within

20 seconds (The PROGRAM LED will glow during the recording

period)

- ThesystemreturnstoDAYMODEaftertherecordingtimeisover

Only one message can be recorded at a time. To record the

secondmessage,theaboveproceduremustberepeated.

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressPLAY

- PressPROG

- Press1toplay IntrusionMessage2ortoplay firemessage

MessagewillplayandpanelwillreturntoDAYMODE.

Only one message can be played back at a time. To play the second

message,theaboveproceduremustberepeated.

- 8 -

- EnterMASTERCODE

-PROGRAMLEDwillblink

- PressPROG

-PROGRAMLEDwillglow

- PressTEL

- PressPROG

- Press 1to set intrusion message numbers 2or to set fire

messagenumbers

- Enter the first number ( Max 14 digits, message, press DIAL for

pausewhenusingEPABX)

- PressENTER,twobeepswillbeheard

- EnterthenextnumberandthenpressENTER

- Continue this process till all numbers are entered (Max 15) and

thenpressENTERtwicetoend

- ThesystemreturnstoDAYMODE

Onlyonemessage numberscanbe enteredatatime.Toenter thesecond

messagenumbers,theaboveproceduremustberepeated.

The system can be brought out of the programming mode by pressing

EXITinsteadofPROG.

The system can dial and play the intrusion message without activating the

sounders.

- PressEnter

- PressDIAL

- 9 -

If the user has FORGOTTEN the code, the panel has to be RESET to

FACTORYSETTINGS

ToresettoFactorySettings:

- Disconnect all power supply and the battery from the main

controlpanel.

- Presskey1and4simultaneously

- Reconnect the power supply while keeping 1and 4keys

pressed.

- The panel will reset to factory settings and MASTER CODE will

beresetto1234.

Pleaserefertosection1-3forFactorySettings.

In order to make it easier to operate the control panel, the key pad is fully

backlit. The key pad will illuminate if a button is pressed or any zone is

opened.ThelightSWITCHOFFautomaticallyafter2minutes.

As an additional safety feature, the control panel has one mains AC fuse

on the power supply card and TWO SAFETY FUSES on the main circuit

board.Intheeventofanoverloadinthepowersupply,sounderorauxiliary

supply circuits, a fuse will blow. This fuse must be replaced. You may

contactyournearestservicecentreforassistance.

- 10 -

ELECTRICAL

Quiescentcurrent:75mAtypical

Currentwithdialing&massageplay:160mA

Maximumsounder1currentoutput:1A

Maximumsounder2currentoutput:1A

SoundersaturationVoltage:<1Vat1A

Remotekeypads:Uptofive

Non-volatileMemory:ProgrammingandLog

Zoneresponsetime:<500ms

ZoneLoopsResistance:<5kohmforNORMALLYCLOSED

POWERSUPPLY

MainssupplyVoltage:220+10%-15%50Hz

TotalcurrentOutput:800mAat220VAC(FuseJA20mmOnMainCard)

Regulation:<9%

Ripple:<200mVRMS

Batteryvoltage:12VDC

Battery type:SMFRechargeable

Batteryrecharge voltage:13.8V+/-0.2VD

Fuse:250mA20mmACMainsonPSCard

ENVIRONMENTAL

OperatingTemperature:0ºCto45ºC

StorageTemperature:-20ºCto60ºC

Maximumhumidity:95%non-condensin

Environment:residential/commercial/lightIndustrial

PHYSICAL

Dimensions:236mmx226mmx80mm

MaxBatteryDimensions:150mmx110mmx64mm

- 11 -

- 12 -

1) +Z1- ToZONENO.1Devices(Shortwithjumperifnotapplicable

2) +Z2- ToZONENO.2Devices(Shortwithjumperifnotapplicable

3) HELP ToPANICZONEDevices(Shortwithjumperifnotapplicable

4) FIRE ToFIREZONEDevices(Shortwithjumperifnotapplicable

5) -HT1+ To SOUNDERS

6) -HT2+ To AdditionalSOUNDERS/STROBELIGHT

7) -AUX+ 12VDCSupplytosensor/detectors

8) -LO+ Telephonelineouttootherextensions

9) LI+ELI- Telephonelinein

- 13 -

- 14 -

Inhaltsverzeichnis

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung