Securitron EcoPower EPS-05 Bedienungsanleitung

1 500-33530, Rev B



EcoPower™ Power Supply

Owner’s Manual



2 500-33530, Rev B

Table of Contents

Warranty....................................................................................................2

Models.......................................................................................................3

Structure....................................................................................................3

Block Diagram...........................................................................................4

Specifications............................................................................................4

Environmental .......................................................................................4

Mechanical ............................................................................................5

Electrical................................................................................................5

Regulatory Certifications .......................................................................6

Regulatory Compliance.........................................................................7

UL294 Access Control Performance Levels for Model EPS-05

Power Supply ........................................................................................7

Status Signaling ....................................................................................8

Access Control and FAI Operations..........................................................8

Installing the EcoPower Power Supply...................................................11

Install the EcoPower Power Supply using the included enclosure

box (flush with the wall stud and wall surface)....................................11

Install the EcoPower Power Supply using the included enclosure

box and surface mounted....................................................................15

Install the EcoPower Power Supply flush with the stud in an

existing 2-gang junction box................................................................17

Warranty

The EcoPower™ Power Supply is covered by the MagnaCare®lifetime

replacement no fault warranty. No registration is required. Product will

be replaced forever, for any reason, including but not limited to installation

error, vandalism, or act of God. Replacement product is shipped at

Securitron’s expense next day air if needed.

For more information, visit www.securitron.com

3 500-33530, Rev B

Models

EPS-05 EcoPower Power Supply in Enclosure

EPS-05B EcoPower Power Supply PCB only

Structure

4 500-33530, Rev B

Block Diagram

Specifications

Environmental

Parameter Value

Operating Ambient Temperature 0 to +49° Celsius (C)

Design Product Life 10 years, +49°C ambient,

continuous full load

Storage Temperature -25 to +85°C

Operating Humidity 5 to 90%, non-condensing

5 500-33530, Rev B

Mechanical

Parameter Value

Enclosure Polycarbonate, UL294 Level 1

Enclosure dimensions 4 1/8” X 4 1/8” X 3 13/16”

AC input wiring 3-wire with strain relief

DC1, LOCK, BAT, FAI, ACC wiring 10-position terminal strip

Electrical

Parameter Value

Input Voltage Range 100–240 VAC, ±10%

Input Frequency 50–60 Hz

Input Surge Resistance 6000 Vpk

Access Control Input Dry Contact, NO or NC; 32

VDC, 0.02A minimum

Fire Alarm Interface Input Dry Contact, NO or NC; 32

VDC, 0.02A minimum

Hi-Pot Test 2500 VAC or 3535 VDC

Leakage Current < 0.5 mA

Output Voltage at No Load Set to 14.0 VDC, ± 0.2%

Number of Outputs Two (2) Outputs:

DC1 (Reader): 12 VDC nominal

(9.4–14.6 VDC for compatibility)

LOCK: 12 VDC nominal (9.4–

14.6 VDC for compatibility)

If the battery is discharged

below 9.4V, the lock output is

de-energized

Total Peak Output Current 0.5A (Total current from both

outputs for at least 1 second)

Total Continuous Output Current 0.1A (Total continuous current

from both outputs)

Charging Current (BAT) 12 VDC nominal, 0.1A

maximum continuous, 0.34A

peak (< 2 seconds)

Standby Power < 20 mW at 230V, < 10mW

at115V

Load Regulation < 2.5% at 100 mA

Line Regulation < 0.2%

6 500-33530, Rev B

Output Voltage Ripple and Noise < 0.14 Vpp (20 MHz bandwidth

limit measurement)

Output Surge Resistance 2400 Vpk

Output Over Voltage Protection Under any single point

condition, output voltage shall

not exceed 120% of nominal

voltage

Battery Type and Capacity Sealed Lead Acid (SLA), 12V,

0.8 Ah

Battery Standby Time 20.5 hours dependent on lock

type (FSA or FSE) and usage.

Battery standby time is

designed for EcoFlex lock with

optional H1 controller only (not

for 100 mA load). H1 controller

draws an average of 5 mA.

The two total current draw is

about 20 mA.

Total Load Current 0.8 Ah Battery Backup Time

20 mA 20.5 hours

50 mA 6.5 hours

100 mA 2 hours



Regulatory Certifications

•UL294, "Access Control System Unit," 6th Edition

•UL603, "Power supply for use with Burglar Alarm System," 5th

Edition

•CAN/ULC-S533, "Egress Door Securing and Releasing Devices,"

3rd Edition

•GreenCircle Certified (99% Energy Savings)

NOTE: 50% - battery discharge time from fully charged

condition.

7 500-33530, Rev B

Regulatory Compliance

•EN60950-1:2006+A11:2009+A1:2010+A12:2011, "Information

Technology Equipment–Safety”

•FCC Part 15, Subpart B, "(unintentional radiator), Class A for

industrial and commercial use"

•EN55022:2010, "Class A for industrial and commercial use”

•EN55024:2010

•EN61000-3-2:2006+A1:2009+A2:2009

•EN61000-3-3:2008

•CE LVD and EMC directives currently in effect

•EU RoHS Directive

•EU REACH Regulation

UL294 Access Control Performance Levels for Model

EPS-05 Power Supply

NOTE: Without an attack-resistant enclosure, the EPS-05 cannot

power Mercantile, Bank Safe and Vault audible alarm

devices or Digital Alarm Communicator Transmitters

(DACTs).

Access

Control

Line

Security

Destructive

Attack Endurance Standby

Power

Example Conditions

and Notes

I I IV IV

Standby Power Level

IV when used with

Ecoflex Lock and H1

Controller

8 500-33530, Rev B

Status Signaling

Green LED Signaling AC Power Mode: Solid on

AC Standby Mode: 2s on / 2s off

AC Lost Mode: 1s on / 2s off

Output Voltage Abnormal: OFF

Battery Disconnected: Rapid flash (4 times per

second, then off for 1 second)

NOTE: Black text indicates condition; green text

indicates corresponding LED lighting pattern.

Red LED Signaling Power Supply Alarm Mode: ON

Power Supply Normal Mode: OFF

Output Voltage Abnormal: Blink at 1 Hz

Battery Discharged Below 9.6V: Blink at0.5 Hz

NOTE: If alarm has occurred and FAI set to

latch mode, power supply stays in alarm mode

until the reset button on the front panel is

pressed.

Buzzer Beep at 1/3 Hz for 30 seconds every 15 minutes

NOTE: Reset battery by pressing the reset

button on front panel for 5 seconds to silence

alarm for 24 hours.

Access Control and FAI Operations

The following table describes how the lock power output (DC2) responds

to the access control input under various DIP switch settings. This table

is only valid when the EcoPower has not received a fire alarm activation

signal at the FAI input.

Access Control

Input DIP Switch Settings Output

Access Dry

Contact State

Access DIP

Switch

Setting

Lock Type DIP

Switch Setting

LOC

Output

Voltage

FAI LED

(RED)

Open NO Fail-Safe (FSA) On Off

Open NO Fail-Secure (FSE) Off Off

9 500-33530, Rev B

Access Control

Input DIP Switch Settings Output

Access Dry

Contact State

Access DIP

Switch

Setting

Lock Type DIP

Switch Setting

LOC

Output

Voltage

FAI LED

(RED)

Open NC FSA Off Off

Open NC FSE On Off

Closed NO FSA Off Off

Closed NO FSE On Off

Closed NC FSA On Off

Closed NC FSE Off Off

NOTE: Because the lock circuit fails secure, listed panic hardware

shall be used to allow emergency exit from the protected

area.

The following table describes lock power output behavior when there is

an active fire alarm signal at the FAI input. This ensures the door is

unlocked when there is an active fire alarm signal. It should be noted

that the FAI signal will always override the access control signal.

FAI Signal DIP Switch Settings Output

FAI Dry Contact

State

FAI DIP

Setting

Lock Type DIP SW

Setting

LOCK

Output

Voltage

FAI LED

(RED)

Open NC FSA Off On

Open NC FSE On On

Closed NO FSA Off On

Closed NO FSE On On

10 500-33530, Rev B

NOTE 1: Unit should only be connected to a fire alarm panel when

used in a FSA configuration.

NOTE 2: If the DIP switch for FAI latching is set to the “Latched”

Position, the LOCK output and the red LED will remain in fire

alarm state even when an active FAI input is removed. The

user will need to depress the reset button on the bottom right

of the front panel for 1 second (see Figure 1, “Reset Button

and LED Locations”) to reset the fire alarm state (red LED off

and lock per access control input). The factory default DIP

switch settings are as follows:

DIP Switch Name Default Position Notes

Access control input Normally Open (NO) Normally Closed (NC)

FAI input NO NC

FAI Latch FAI Latching Disabled FAI Latching Enabled

Lock Type Fail-Safe (FSA) Fail-Secure (FSE)

Figure 1: Reset Button and LED Locations

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Securitron Stromversorgung Handbücher

Securitron

Securitron AQD5 Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung