Seiko V137A Bedienungsanleitung

PARTS LIST /TECHNICAL GUIDE

ANALOGUE SOLAR Cal. V137A

[SPECIFICATIONS]

1/18

Item Cal. No. V137A

Power reserve

Driving system

Additional function

Crown operation

Loss/Gain

Regulation system

Number of jewels

Normal position

1st click position

Current consumption

Gate time for rate measurement

Power

supply

Motion of the second hand

Coil resistance

Power generator

Rechargeable battery

Operating voltage range

2nd click position

One-second intervals

Stepping motor 1 piece (Load compensated driving pulse type)

Diameter: Outside 18.5 mm

17.5 mm (between 3 o’clock and

9 o’clock )

Casing 18.1 mm

Height: 2.6 mm

• Energy depletion forewarning function (The second hand moves at two-second

intervals.)

• Overcharge prevention function

• Electronic circuit reset function

• Second hand stop function

• Date calendar

• Instant setting device for date calendar

Free

Time setting

Monthly rate:less than 15 seconds (worn on the wrist at temperature range

between 5 to 35 degrees Centigrade)

Use 10-second gate

Nil

Solar power generation system

Movement: less than 0.75 µA

Circuit block: less than 0.30 µA

Coil block: 1.60-2.20 kΩ

MT621 Manganese titanium lithium rechargeable battery

0.90V - 2.20V

From full charge to stoppage: Approximately 6 months

2 jewels

Date setting (clockwise)

3 hands

(hour, minute and small second

hands)

Cal. V137A

PARTS LIST

2/18

FEATURES

Cal. V137A is an analogue watch with a solar power generation system.

l Solar power generation system

The watch operates while charging electricity by converting light received on the dial to

electrical energy. It lasts for 6 months after full charge.

l Energy depletion forewarning function

When the energy stored in the rechargeable battery is reduced to an extremely low level, the

second hand starts moving at 2-second intervals instead of the normal 1-second intervals.

l Guideline of charging time

Environment/Light source Illumination

(lux)

Time required

for full charge

Time required

for steady

operation

Time to charge

1 day of power

General ofﬁces/ Fluorescent

Light

700 -16 hours 110 minutes

30W 20cm/Fluorescent light 3,000 90 hours 4 hours 30 minutes

30W 3cm/ Fluorescent light 10,000 30 hours 1.2 hours 8 minutes

Cloudy weather/Sunlight 10,000 30 hours 1.2 hours 8 minutes

Fair weather/Sunlight 100,000 10 hours 0.1 hours 1 minutes

The above table provides only a general guideline.

It is recommended that the watch be charged for as long as the charging time according to the

column "Time required for steady operation" in this table in order to assure the stable movement

of the watch.

l Caution for charging

When charging the watch, do not place it too close to a photo ﬂash light, spotlight, incandescent

light or other light sources as the watch temperature will become extremely high, causing damage

to the parts inside the watch.

When exposing the watch to sunlight for recharging, do not leave it on the dashboard of a car, etc.

for a long time, as the increase of watch temperature to an extremely high level can damage watch

parts or cause malfunctions.

While charging the watch, make sure the watch temperature does not exceed 60 °C.

Order of disassembly: 1 34

Order of assembly: 34 1

1 HOUR, MINUTE

AND SECOND

HANDS

2 DIAL

3 DIAL SHEET

8700 ***

4 SOLAR CELL

4025 562

8 CASE RING

MOVEMENT

5 HOLDING RING

FOR DIAL

0866***

6 DIAL WASHER

0491 735

7 CONTACT POINT

SPRING FOR SOLAR

CELL (3 PCS.)

4246 529

9 DATE DIAL GUARD

0808 891

10 DATE DIAL

0878***

11 DATE JUMPER

0810 890

12 HOUR WHEEL

0271 647

13 DATE DRIVING

WHEEL

0802 891

Types of oil

AO-3

AO-2

Oil quantity

Small quantity

Normal quantity

Liberal quantity

PARTS LIST Cal. V137A

3/18

Please see the remarks on the following pages.

14 RECHARGEABLE BATTERY

BLOCK

3026 24X

15 CIRCUIT BLOCK

COVER SCREW

(3PCS.)

0022 247

16 CIRCUIT BLOCK

COVER

4461 548

17 CIRCUIT BLOCK

4000 775

Cal. V137A

PARTS LIST

4/18

Please see the remarks on the following pages.

18 TRAIN WHEEL BRIDGE

0125 517

19 FOURTH WHEEL AND

PINION

0241 173

20 THIRD WHEEL AND

PINION

0231 904

23 MINUTE WHEEL

0261 904

21 FIFTH WHEEL AND PINION

0701 904

22 STEP ROTOR

4146 907

24 TRAIN WHEEL

SETTING LEVER

0391 890

25 SETTING LEVER

0383 891

27 SETTING WHEEL

0281 904

26 YOKE

0384 890

28 SETTING STEM

0351 892

29 CLUTCH WHEEL

0282 890

30 DATE CORRECTOR WHEEL

0806 890

31 COIL BLOCK

4002 543

32 ROTOR STATOR

4239 549

33 CENTER WHEEL

AND PINION

0221 607

34 MAIN PLATE

0100 605

PARTS LIST Cal. V137A

5/18

Please see the remarks on the following pages.

Cal. V137A

PARTS LIST

6/18

l

How to ﬁnd the correct parts, if not determined by 4 digit caliber number

Following parts are determined based on the design of watches, such as hands height, dial color,

and design of cases. Please refer to the SEIKO WATCH PARTS CATALOGUE in order to choose

the corresponding parts.

5 HOLDING RING FOR DIAL 0866 ***

10 DATE DIAL 0878 ***

SETTING STEM 0351 892

l

Other parts to pay attention to:

2 DIAL

3 DIAL SHEET

DIAL SHEET is used or not used depending on the design of watches.

Whether it is used or not can be judged from parts number of the DIAL.

Model with DIAL SHEET: The 9th digit of Dial number is “T.“

Example: V1370AA0TS14

Model without DIAL SHEET: The 9th digit of Dial number is “X.“

Example: V1370AA0XS14

l

Rotation movement:

The RECHARGEABLE BATTERY BLOCK is not assembled in the replacement movement for Cal.V137A.

PARTS LIST Cal. V137A

7/18

lTools and consumables required for disassembling/reassembling

•Movement holder

UNIVERSAL MOVEMENT HOLDER (S-682)

• Watch oils

SEIKO watch oils (AO-3 and AO-2)

AO-3 AO-2

4 SOLAR CELL

5 HOLDING RING FOR DIAL

* It is not necessary to separate the SOLAR CELL and the HOLDING RING FOR DIAL except in the case

that a part needs to be replaced.

• Disassembling and Reassembling of HOLDING RING FOR

DIAL

1. The HOLDING RING FOR DIAL is ﬁxed to the movement by

the hooking portion at 12 o’clock and 6 o’clock positions.

2. Insert the tip of a screwdriver into the gap between the

hooking portion and main plate to release the hooking

portion from the main plate as shown with the arrow mark

in the illustration.

TECHNICAL GUIDE Cal. V137A

8/18

REMARKS ON DISASSEMBLING AND REASSEMBLING

REMARKS ON DISASSEMBLING AND REASSEMBLING THE MOVEMENT

Set the notched portions of the DIAL SHEET to the guide post

(4 posts) of the HOLDING RING FOR DIAL, and check that the

DIAL SHEET is ﬁxed in position.

• Howtoinstall

2 DIAL

• Howtoinstall

3 DIAL SHEET (Not used in some models)

Set the notched portions of the DIAL to the guide posts (4 posts)

of the HOLDING RING FOR DIAL, and check that the DIAL is

ﬁxed in position.

1. Set the 2 hooking portions to 12 o’clock and 6 o’clock

positions as shown in the illustration.

2. Gently push the hooking portions of HOLDING RING

FOR DIAL so that they catch the main plate securely.

TECHNICAL GUIDE Cal. V137A

9/18

• DisassemblingandReassemblingofSOLARCELL

* Do not apply excessive force to the SOLAR CELL.

* Just like COIL BLOCK, SOLAR CELL gets damaged easily by static electricity. Be careful not

to get it magnetized, especially the part where it touches CONTACT POINT SPRING.

As there are 2 connection parts of the HOLDING RING FOR DIAL, release them side by side.

Set the SOLAR CELL to 2 guide posts, and assemble

it to the HOLDING RING FOR DIAL by gently pushing

the hooking positions of the SOLAR CELL as shown

by the arrow marks in the illustlation.

7 CONTACT POINT SPRING FOR SOLAR CELL

Set 3 pcs of CONTACT POINT SPRING FOR SOLAR CELL at the

correct position as shown in the illustration.

Note: While other solar movements normally use 2 pcs of

CONTACT POINT SPRING FOR SOLAR CELL, 3 pcs are used in

Cal. V137. The third piece is assembled to keep the metallic part

under the SOLAR CELL in positive potential in order to stabilize

the watch’s performance.

9 DATE DIAL GUARD

1. Lightly lift the A portion of the date dial guard with

tweezers to release it from the guide pin, and then move

it in the counterclockwise direction to put it on the guide

pin.

2. Release the B portion of the date dial guard in the same

way as described above.

3. Check that all the three hooking portions of the DATE

DIAL GUARD have come off from the MAIN PLATE, and

then remove the DATE DIAL GUARD.

1. Put the DATE DIAL GUARD on the MAIN PLATE so

that the A and B portions are over the guide pins, as

shown in the illustrations at right.

2. Move the portion D in the clockwise direction so that

it is caught under the MAIN PLATE.

3. Slightly move the portions C and E in the clockwise

direction alternately to set them under the MAIN

PLATE. Then, set the A and B portions to the guide

pins.

4. Check that the DATE DIAL GUARD is ﬁxed securely to

the MAIN PLATE.

TECHNICAL GUIDE Cal. V137A

10/18

A PORTION

B PORTION

HOOKING PORTIONS

DATE DIAL

GUARD

GUIDE PIN

TWEEZERS

C PORTION

B PORTION PORTION D

E PORTION

A PORTION

Inhaltsverzeichnis

Andere Seiko Betrachten Handbücher

Seiko

Seiko 4R57 Bedienungsanleitung

Seiko

Seiko Conceptual SUR533P Bedienungsanleitung

Seiko

Seiko Spectrum SVRD001 G510 Bedienungsanleitung

Seiko

Seiko 7S26 Bedienungsanleitung

Seiko

Seiko Pulsar 7T32 Bedienungsanleitung

Seiko

Seiko C-26 Bedienungsanleitung

Seiko

Seiko SARW043 Bedienungsanleitung

Seiko

Seiko Presage SPB399J Bedienungsanleitung

Seiko

Seiko GPS SOLAR ASTRON 5X53 Montageanleitung

Seiko

Seiko G757(GZC) Bedienungsanleitung

Seiko

Seiko Cal. 5M82 Bedienungsanleitung

Seiko

Seiko 0439A Kurzanleitung

Seiko

Seiko King Seiko SPB371J Bedienungsanleitung

Seiko

Seiko Map Meter / Mile Marker Bedienungsanleitung

Seiko

Seiko KINETIC 7D48 Bedienungsanleitung

Seiko

Seiko Pulsar Y182 Bedienungsanleitung

Seiko

Seiko SFJ001P Bedienungsanleitung

Seiko

Seiko V194 Bedienungsanleitung

Seiko

Seiko Cal. 8L35 Bedienungsanleitung

Seiko

Seiko DH33A Installationshandbuch

Seiko

Seiko 6R24A Kurzanleitung

Seiko

Seiko V693A Installationshandbuch

Seiko

Seiko KINETIC 7L22A Installationshandbuch

Seiko

Seiko SRWZ24 Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung

iTOUCH

iTOUCH 3360 Bedienungsanleitung