Sekonic SR-3500 Bedienungsanleitung
-1-
Introduction
Thank you very much for purchasing our product.
Please read the operating manual before using this product, and be sure to use it properly.
After reading this operating manual, be sure to keep it in a place that you can access at any time.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Introduction
-2-
Table of contents
Safety precautions ............................................................................................. 5
Before using ......................................................................................................... 8
Power cord list for Europe ................................................................................. 11
Warranty ................................................................................................................. 12
Precautions for use ........................................................................................... 13
Names of parts .................................................................................................... 16
Operating panel functions and operating instructions ............................... 18
Product specications ..................................................................................... 19
Operation
Preparation ...................................................................................................... 21
Turning power on ............................................................................................ 25
Loading paper ................................................................................................. 26
Setting paper weight ...................................................................................... 28
Marking instructions ......................................................................................... 29
Connecting to a computer ............................................................................. 30
USB
1. Operating mode ............................................................................................ 31
2. Interface settings .......................................................................................... 32
RS-232C
1. Operating mode ............................................................................................ 33
2. Interface settings
2-1. Setting baud rate .................................................................................. 34
2-2. Setting character bit length .................................................................. 34
2-3. Setting parity ........................................................................................ 35
2-4. Setting stop bit ..................................................................................... 36
2-5. Setting ow control .............................................................................. 36
2-6. Setting character code ......................................................................... 37
Data reading settings
Setting column ................................................................................................ 38
Setting reading method .................................................................................. 39
Setting min. density level ............................................................................... 41
Setting density balance .................................................................................. 42
Setting reading side ........................................................................................ 43
Setting paper weight ...................................................................................... 44
Setting paper hold(SR-3500) ........................................................................... 45
Error detection settings ................................................................................... 46
Buzzer settings
Buzzer control ................................................................................................. 48
Buzzer sound adjustment .............................................................................. 49
Table of contents
-3-
Stacker settings .................................................................................................. 50
Printer settings
Printer control ................................................................................................. 51
SR-2300 SR-6500 mode
1. Character size setting ................................................................................... 52
2. Character interval setting .............................................................................. 53
SR-600 SR-9000 mode
1. Character size setting ................................................................................... 55
2. Character magnication setting .................................................................... 56
3. Character interval setting .............................................................................. 57
Barcode settings
Barcode control .............................................................................................. 59
Low power consumption settings
Sleep duration .................................................................................................. 60
Stanby duration ................................................................................................ 61
Displaying various information
Displaying the version .................................................................................... 62
Displaying front side reading sensor settings ............................................. 63
Displaying back side reading sensor settings ............................................. 64
Displaying optional unit settings ................................................................... 65
Displaying total count ..................................................................................... 66
Displaying serial number ................................................................................ 67
Operating tests
Feed test 1 ....................................................................................................... 68
Feed test 2 ....................................................................................................... 69
Printer test ....................................................................................................... 70
Printer jet test ................................................................................................. 71
Options
Stacker unit
Stacker unit specications ............................................................................ 72
Stacker unit (printer) preparation .................................................................. 73
Printing position adjustment ......................................................................... 76
Clearing paper jams ....................................................................................... 79
Stacker unit precautions for use ................................................................... 80
Back side reading unit ..................................................................................... 81
Printer unit
Printer unit specications .............................................................................. 82
Printer uniut preparation ................................................................................ 84
Printable area .................................................................................................. 84
Printing position adjustment ......................................................................... 85
Printer unit precautions for use .................................................................... 87
Barcode unit / V • Barcode unit / H
Barcode unit specications ........................................................................... 88
Table of contents
-4-
Barcode readable area ................................................................................... 90
Barcode reading position adjustment .......................................................... 92
Barcode unit precautions for use .................................................................. 94
Cleaning ................................................................................................................. 95
Cleaning procedures ...................................................................................... 95
Cleaning point ................................................................................................. 96
Service schedule .............................................................................................. 100
External diagram .............................................................................................. 102
List of menu modes ......................................................................................... 104
Error displays and countermeasures
1. Errors ........................................................................................................... 107
2. Warnings ..................................................................................................... 111
OMR glossary .................................................................................................... 114
Appendix Sheet creation reference
Table of contents
-5-
Safety Precautions
These “Safety Precautions” pages list various symbols for ensuring safe operation of this
product so as to prevent users or other people from being injured, or property from being
damaged.
Read these precautions thoroughly and understand the meanings of the symbols before
proceeding to the main text of this manual.
Safety Precautions
Warning
Improper operation by neglecting these instructions may result in death or serious
injury.
Caution
Improper operation by neglecting these instructions may result in personal injury or
property damage.
Neglecting these instructions may generate smoke or re.
Neglecting these instructions may cause electric shock.
Indicates a prohibited action.
Indicates that disassembly or modication is prohibited.
Indicates that the power plug must be removed from the outlet for safe
operation.
Instructs that do not spray the materials containing an inflammble gas or
liquid to the device.
-6-
Warning
Warning
Fire or electric shock may result if this product continues to be used
when there is a strange smell or sound.
In such a case, immediately turn the power switch off and then remove
the power plug from the outlet. After making sure that it is no longer
smoking, ask the sales shop for repair service.
Never attempt to repair by yourself since that may be very dangerous.
Do not modify or disassemble this device. That could cause fire or
electric shock.
Do not remove the cover from this device. That could cause electric
shock. Ask the sales shop to conduct any internal checking,
adjustment or repair.
Pay thorough attention to the above instructions. Otherwise, fire or
electric shock may occur.
Power plug precautions
• Do not pull on the cord when removing the power plug from the outlet.
• Do not use any power plug other than the specied one.
Make sure to use the adapter included in the package.
Device precautions
• Do not use it with a supply voltage other than the specied one.
• Do not install it in a place that may be wet with water or oil, steam,
moisture or dust.
• Do not insert or drop any metal, foreign combustible matter, etc., into
the port.
• Do not place containers with chemicals or water, or small metal pieces
near the device.
Do not cover the vent hole. That could cause heat retention, resulting
in re.
If the device is dropped or the cover is broken, immediately turn the
power switch off and remove the power plug from the outlet. Then,
contact the sales shop.
If any foreign matter should enter inside, immediately turn the power
switch off and remove the power plug from the outlet. Then, contact
the sales shop or Sekonic. If the device continues to be used with
foreign matter inside, re or electric shock may occur.
If water or other substances penetrate the unit, immediately turn the
power switch off and remove the power plug from the outlet. Then,
contact the sales shop or Sekonic. If the device continues to be used with
water or other foreign matter inside, re or electric shock may occur.
Do not spray any materials containing an inammable gas or liquid on
the device and be sure to keep this kind of materials away from this
device.
Use a cleaning cloth with suitable amount of cleaning liquid to wipe
off well, after removing the power plug from the outlet and the device
becomes to cool off.
-7-
Caution
Do not put heavy things on the device. Otherwise, it may fall or
collapse, resulting in injury.
Do not place the device in an unstable location. Otherwise, it may
fall or collapse, resulting in injury.
When opening or closing the upper part of the main body, do not
place your hand on the paper-feeding surface. Otherwise, fingers
may be caught, resulting in injury.
If you must touch the paper-feeding surface of the main body, be
careful not to allow your ngers to be caught or hit.
When doing maintenance on the device, for your own safety, be sure
to remove the power plug from the outlet.
When the device is not in use for long periods, for safety, remove the
power plug from the outlet.
Before moving the device, be sure to remove the power plug from
the outlet. If the cable is damaged, re or electric shock may occur.
Do not connect or disconnect the power plug if your hands are wet.
Otherwise, an electric shock may occur.
Caution
-8-
Before using(SR-3500)
Before using the device, check if all of the following items are included in the package. If
components are missing or damaged, contact the store where you purchased the device.
Note)
The package doesn’t include a RS-232C(9 pins) interface
cable. You may need to get one depending on your computer
port or connection method.
5. Power cord
For U.S.A
Mark entry sheet:
use it as an example when
designing entry sheets.
6. Operating manual
(this booklet)
7. A4 check sheets (5 sheets)
A4 mark entry sheets (5 sheets)
9. USB cable
1. Main body unit 2. Paper receiver 3. Paper discharge brackets
(
x 2: Not used when the select
)
stacker unit is installed.
For Europe
Note)
Refer to the power cord list
for Europe of next page.
8. CD-ROM
4. Paper feeding bracket
(
Not used when the select
)
stacker unit is installed.
Check sheet:
use it for checking OMR operations.
Operating manual
Before using
-9-
Before using
2. Strage bag
(Transparent plastic bag)
Stacker unit (Option)
* See the installation manual for components to be used for installation.
1. Stacker 2. Main tray 3. Selection tray
Printer unit (Option)
1. Ink cartridge
-10-
Before using(SR-6500)
Before using the device, check if all of the following items are included in the package. If
components are missing or damaged, contact the store where you purchased the device.
5. Power cord
For U.S.A
6. Operating manual
(this booklet)
9. USB cable
1. Main body unit 2. Main tray 3. Selection tray 4. Paper feeding
bracket
For Europe
Note)
Refer to the power cord list
for Europe of next page.
8. CD-ROM
10. Ink cartridge
Mark entry sheet:
use it as an example when
designing entry sheets.
7. A4 check sheets (5 sheets)
A4 mark entry sheets (5 sheets)
Check sheet:
use it for checking OMR operations.
11. Strage bag
(Transparent plastic bag)
Operating manual
Note)
The package doesn’t include a RS-232C(9 pins) interface
cable. You may need to get one depending on your computer
port or connection method.
Before using
Andere Handbücher für SR-3500
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
