Sel 651RA Bedienungsanleitung

Date Code 20160329 SEL-651RA Recloser Control

Introduction

This 8-pin (size 22) receptacle provides an eight-pin male receptacle that exits

from the bottom of the cabinet. The 8-pin cable is internally wired to 300 Vac

voltage max inputs. The 8-pin receptacle provides a convenient way (by way

of external cable, which is not included) to connect external potential

transformer secondary outputs to the control. Depending on the secondary

input voltage option of your control, you may wire to just the Y-side, just the

Z-side, or both Y- and Z-side voltage inputs.

Parts

Installation

Step 1. Install the 8-pin (size 22) voltage input receptacle harness in

the bottom of the cabinet in the center hole in the back row. See

Figure 1.

a. Insert the receptacle harness inside the cabinet and

insert the four screws from outside.

b. Install the nuts on the screws from the inside of the

cabinet.

Step 2. Install the smaller ring terminal of the green/yellow ground

wire and the two drain wires to the last connector screw and

secure them with the last nut. See Figure 1.

Step 3. Use the existing nut to connect the larger ring terminal of the

green/yellow ground wire to the ground stud. See Figure 1.

SEL Part Number Description Quantity

SEL-C2253 8-pin (size 22) voltage input receptacle harness 1

SEL-C5241 Ground wire 1

080-0101 5/8 steel wire clamp 2

140-0500 4-40 x 1/2" screw 4

140-0740 4-40 hex nut 4

144-0140 Plastic cap 1

310-0050 Zip ties 12

SEL-651RA Installation Instructions for 8-Pin

(Size 22) Receptacle for Voltage Inputs

SEL-651RA Recloser Control Date Code 20160329

Figure 1 Install Ring Terminal

Step 4. If your unit is equipped with the fuse block for field wiring, go

to Wiring With Fuse Block. Otherwise, go to Wiring Without

Fuse Block.

Wiring Without Fuse

Block

Step 1. Form a drip loop and route the harness wires to the left toward

the 14-pin connector. See Figure 2.

Figure 2 Form Drip Loop and Route Harness Wires

Step 2. Join the 8-pin wires with the main harness and route the wires

through the wire loom and up the swing panel hinge through

the existing wire clamps.

Step 3. Route the wires across the top of the control module. The

accessory wires route separately from the main harness.

Step 4. Use the existing nuts to secure the wires to the top of the

control module with the two accessory wire clamps (if they are

not already installed). See Figure 3.

Date Code 20160329 SEL-651RA Recloser Control

Figure 3 Secure Wires on Top of Control Module

Step 5. Attach the eight-pin harness wires according to the table in

Figure 4 as required for your specific secondary input voltage

option. See Tabl e 1 for SIV-specific wiring. Note that the

Z-side wires have white heat shrink on the ring terminals.

Figure 4 Attach Wires to Control Module

Step 6. Zip tie wires as necessary.

Table 1 SIV-Specific Wiring

SIV Option MOT Character Wire

Single phase 1 A, B, C, D only (Y side)

6 PT A A, B, C, D, E, F, G, H (Y and Z sides)

Z-side PT B E, F, G, H only (Z side)

Z-side PT D E, F, G, H only (Z side)

Y-side PT F A, B, C, D only (Y side)

Main Harness

Accessory Wires

8-Pin Wires: To:

Z09

Z10

Z11

Z12

A (Black Wire)

B (Brown Wire)

C (Red Wire)

D (Orange Wire)

Z13

Z14

Z15

Z16

E (Black Wire)

F (Brown Wire)

G (Red Wire)

H (Orange Wire)

SEL-651RA Recloser Control Date Code 20160329

Wiring With Fuse

Block

Step 1. Form a drip loop and route the harness wires to the bottom of

the fuse block for field wiring. See Figure 5.

Figure 5 Route Harness Wires to Bottom of Fuse Block

Step 2. Cut the cables to a reasonable length, remove about 2 inches of

the jacket, and strip the individual wires about 7/16 of an inch.

Step 3. The Z-side cable is marked with white heat shrink on the Z-side

ring terminals to distinguish them from the Y-side ring

terminals. Mark the end of the Z-side wires (wires from where

the heat shrunk ring terminals were cut) for future reference.

Step 4. Attach the 8-pin harness wires according to the table in

Figure 6 as required for your specific secondary input voltage

option. See Tabl e 1 for SIV-specific wiring.

Date Code 20160329 SEL-651RA Recloser Control

Figure 6 Attach Wires to Fuse Block

Step 5. Zip tie wires as necessary.

From: 8-Pin

Black Wire (A, No Heatshrink)

Brown Wire (B, No Heatshrink)

To: Fuse Block

V1Y - Bottom

V2Y - Bottom

Red Wire (C, No Heatshrink)

Orange Wire (D, No Heatshrink)

V3Y - Bottom

NY - Bottom

Black Wire (E, Heatshrink)

Brown Wire (F, Heatshrink)

V1Z - Bottom

V2Z - Bottom

Red Wire (G, Heatshrink)

Orange Wire (H, Heatshrink)

V3Z - Bottom

NZ - Bottom

Z-sideY-side

SEL-651RA Recloser Control Date Code 20160329

Wiring Diagrams

Without Fuse Block

Ground Stud

Drain

Date Code 20160329 SEL-651RA Recloser Control

With Fuse Block

Ground Stud

Drain

Wiring between fuse block

and control module not shown.

V1Y

V2Y

V3Y

V2Z

V3Z

V1Z

SEL-651RA Recloser Control Date Code 20160329

All brand or product names appearing in this document are the trademark or regis-

tered trademark of their respective holders. No SEL trademarks may be used with-

out written permission. SEL products appearing in this document may be covered by

U.S. and Foreign patents.

Schweitzer Engineering Laboratories, Inc. reserves all rights and benefits afforded

under federal and international copyright and patent laws in its products, including

without limitation software, firmware, and documentation.

The information in this document is provided for informational use only and is sub-

ject to change without notice. Schweitzer Engineering Laboratories, Inc. has

approved only the English language document.

This product is covered by the standard SEL 10-year warranty. For warranty details,

visit selinc.com or contact your customer service representative. *PLS651RA-08*

2350 NE Hopkins Court • Pullman, WA 99163-5603 U.S.A.

Tel: +1.509.332.1890 • Fax: +1.509.332.7990

www.selinc.com • inf[email protected]

WARNING

Operator safety may be impaired if the device is used in a manner

not specified by SEL.

AVERTISSEMENT

La sécurité de l’opérateur peut être compromise si l’appareil est

utilisé d’une façon non indiquée par SEL.

Factory Assistance

We appreciate your interest in SEL products and services. If you have

questions or comments, please contact us at:

Schweitzer Engineering Laboratories, Inc.

2350 NE Hopkins Court

Pullman, WA 99163-5603 U.S.A.

Tel: +1.509.332.1890

Fax: +1.509.332.7990

Internet: selinc.com

Email: [email protected]

Inhaltsverzeichnis

Andere Sel Controller Handbücher

Sel

Sel C6200 FlexGen Merkblatt

Sel

Sel SEL-2241 Bedienungsanleitung

Sel

Sel SEL-351R Falcon Bedienungsanleitung

Sel

Sel SEL-3360 Bedienungsanleitung

Sel

Sel SEL-734W Bedienungsanleitung

Sel

Sel TB-03 Bedienungsanleitung

Sel

Sel SEL-3360-2 Bedienungsanleitung

Sel

Sel C6200 FlexGen Bedienungsanleitung

Sel

Sel M2500 Bedienungsanleitung

Sel

Sel SEL-734B Bedienungsanleitung

Sel

Sel C6200 FlexGen Bedienungsanleitung

Sel

Sel 3355-2 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch