Semtech IOT8EUSBREF-1 Bedienungsanleitung

Smart Building

Reference Kit

User Guide

IOT8EUSBREF-1 (EU 868)

IOT9USSBREF-1 (NA 915)

June 2019

Smart Building User Guide | Proprietary Information | Semtech Corporation

Welcome!

The Smart Building Reference kit is designed to provide validation of the network coverage within a

building, accelerate solution development and facilitate a portable demonstration to a wide range of

stakeholders.

By moving the location of the sensors to different spots around the building, users can determine a

gateway’s range of coverage.

By relying on readily-available hardware, solution developers can focus on providing customer value

through data collection and analysis while using off-the-shelf hardware available from external suppliers.

The self-contained nature of the Reference Kit makes it easy to set up, take down and move the network

in a matter of minutes.

All data collected in the kit is displayed on a dashboardaccessible by the user via a browser. The dashboard

shows the type of display which can be created with the data collected. The URL for the dashboard and

how to locate the log in credentials for your kit, are explained under the Getting Started section of this

guide.

Note: The reference kit does not allow access to the underlying data directly or the ability to change the

LoRaWAN Network Server (LNS) to which the gateways are connected. If those are desired requirements,

please contact Semtech at SB[email protected].

Additionally the user may separately access a dashboard that shows a permanent installation of a Smart

Building Reference Solution Kit inside an office facility. This provides the user with a rich set of historical

data to use in demonstrations. To access this dashboard, log in to the following site, using the credentials

below.

URL: lora-developers.semtech.com/smart-building-kit

Password: LoraWan592

The data in each dashboard is stored for a maximum of 30 days.

In this document we explain how to set up and use the kit.

Smart Building User Guide | Proprietary Information | Semtech Corporation

What is in the kit

The kit contains the following:

5 Desk Sensors

2 Grid-Eye Sensors

2 Temperature/Humidity Sensors

2 IR Blasters

5 Door/Window Sensors

5 Room Occupancy Sensors

1 Leak sensor

2 Mini-hub LoRaWAN gateways

1 Wi-Fi to Mobile Portable Hotspot

Getting started

To begin, log in by scanning the QR code or, using Chrome as your web browser,

navigate to lora-developers.semtech.com/smart-building-kit.

Note: Your individual login credentials can either be found on the inside cover of the

kit box, or on the DEVEUI data sheet provided with the kit.

Get to know your Hotspot and Mini-hubs

The mini-hubs and hotspot are preconfigured to work together. The hotspot includes 1GB of free data

service. If you need more data, you will need to sign up for a cellular service plan. For plan options, see

GlocalMe.

If additional options are needed, you can add up to two nano SIM cards in the hotspot. Use a needle to

pull out the available the SIM slots and insert the SIM cards.

Note: The hotspot included in this kit does not support SIM cards that require PIN codes.

Figure 1: Scan to log in

Smart Building User Guide | Proprietary Information | Semtech Corporation

Setting-up the kit

1. Fully charge the hotspot.

2. Once charged, press and hold the hotspot’s power button (#11) for five seconds and wait for the

device to boot.

3. The hotspot will automatically log-in and connect to the GlocalMe service.

Figure 2:

Hotspot Buttons and Ports

Figure 3:

Automatic Logon

Smart Building User Guide | Proprietary Information | Semtech Corporation

4. Once the hotspot displays the Wi-Fi name and Password, as illustrated in you can start setting-up

the mini-hubs.

5. Remove the cover plate on the first mini-hub. If necessary, attach the power adapter before

plugging-in the mini-hub to a wall socket as shown in Figure 5.

6. You will know the mini-hub is connected to the hotspot when the light on top turns green as shown

in Figure 6

Figure 4: GLocal Logon Complete

Figure 5: Plug-in the mini-hub

Figure 6: Connected to Hotspot

Smart Building User Guide | Proprietary Information | Semtech Corporation

Setting-up the sensors

In this kit, we are monitoring room or desk use, temperature, humidity and leaks. To this end, set up the

sensors as follows.

1. Grid Eye sensors are most effective if mounted on the ceiling or inside of a lighting fixture. Use the

adhesive tape provided with the sensor to mount it in an appropriate location in your conference

room. The Grid Eye sensor can be used to determine the number of people occupying a room. The

sensor begins the count when motion is detected and provides an update approximately every 5

minutes thereafter.

2. Window/Door sensors can be mounted on either side of the window frame or door frame, as

illustrated in Figure 7.

Note: The maximum allowable gap between a sensor and the corresponding magnet is 1 cm. Be

sure to align the sensor side with the blue LED to the magnet face with the notch, as illustrated in

Figure 8.

The Door/Window sensor will provide an indication of whether the door or window is open or closed.

Figure 7: Window and Door Sensor Placement

Figure 8: Sensor / Magnet Alignment

Smart Building User Guide | Proprietary Information | Semtech Corporation

3. The Desk Occupancy sensor may be mounted on the underside of a desk using the double-sided

tape provided. For best results, mount the sensor horizontally approximately 25 cm from the front

edge of the desk, as shown in Figure 9.

Figure 9: Desk Occupancy Sensor

Note: The sensor will send a message when motion is detected. No additional messages will be sent

as long as motion is detected anytime within succeeding 5 minute windows. Only after detecting no

motion during a 5 minute period will it send a message indicating that the desk is unoccupied.

Therefore, changes in condition may not be reflected in the dashboard immediately.

The daily Desk Occupancy statistics shown on the dashboard are calculated for the preceding day at

midnight.

4. To detect movement in a room, place the Room Occupancy sensor on a flat surface, such as a table

or bookshelf. The Room Occupancy sensor behaves much like the Desk Occupancy sensor. The two

have different parameters configured to account for the size of the space being monitored.

As with Desk Occupancy statistics, Room Occupancy statistics are only calculated for the preceding

24 hour period at midnight each day.

5. To detect the temperature and humidity in the room, place the Temp/Humidity sensor anywhere in

the room. To mitigate momentary changes in temperature due to opening a door or window, best

practice is to place this sensor away from doors and windows.

Smart Building User Guide | Proprietary Information | Semtech Corporation

6. The IR blaster can control wall-mounted HVAC systems, heaters, televisions and any other

electronic devices that use an infrared signal with a known Pronto code. A list of codes can be found

at either of these two websites:

http://irdb.tk/

http://www.remotecentral.com/cgi-bin/codes/

To use, place the IR blaster so that it is three to five feet from the item to be controlled, facing the

item’s infrared receiver.

Figure 10: Face of the IR Blaster

Next, navigate on your browser to your kit’s dashboard. Click on the Environment tab on the left

hand side. You will be presented with a screen which includes a place where the Pronto code can be

entered as shown in Figure 11.

Figure 11: Entering Pronto codes for the IR Blaster

Smart Building User Guide | Proprietary Information | Semtech Corporation

7. For information about how to remove or replace the battery in any of the devices, scan the QR code

below, or use the Chrome web browser to navigate to https://qrgo.page.link/iWxb.

Note: Regulations require that the battery must be removed from the device when shipping or flying

by air. Alternatively, you can re-insert the plastic tabs to disrupt the battery current.

Changing the Mini-Hub Wi-Fi connection

If you do not want to use the hotspot provided Wi-Fi network, you can configure the mini-hub to use

another network. To do so, follow these steps:

1. Leaving the mini-hub plugged-in, turn off the hotspot.

2. Using a computer, perform a network scan and select the open Wi-Fi network that starts with

MiniHub-xxxxx where xxxxx are the last 6 digits of the mini hub MAC address, as illustrated in Figure

12.

Figure 12: Mini-hub network

Smart Building User Guide | Proprietary Information | Semtech Corporation

3. Once the computer is connected to the mini-hub, open a web browser and type 192.168.4 in the

address bar.

4. Edit the WiFi SSID and WiFi Password to reflect the new WiFi network you want to connect to. Click

Apply to save your changes.

Mini-Hub LED status indicators and button functionality

LED indicators

Table 1 shows what the various LED colors and blink patterns displayed by the mini-hub indicate.

Color(s)

Blink Pattern

Mode

Status

GREEN

blinking 1 sec

WiFi STA not connected

GREEN

blinking 1/4 sec

WiFi STA connected, establishing connection to LNS, conﬁguring radio

GREEN

Solid

WiFi STA connected, Sta on connected to LNS, radio listening

GREEN/

ORANGE

blinking 1/4 sec

WiFi STA connected, CUPS transaction in progress

Note: Do not unplug device in this state

ORANGE

blinking 1/4 sec

CONFIG

Scanning WiFi networks, setting up conﬁguration AP

ORANGE

blinking 1 sec

CONFIG

Conﬁguration AP active

Table 1: LED Status Indicators

Button Functionality

To switch from GW (gateway) mode to CONFIG mode, press the Setup button for 10 seconds.

To reboot the mini-hub, while in CONFIG mode, press the Setup button for 5 seconds.

To return the mini-hub to factory settings, (and delete the Wi-Fi and LoRaWAN Network Server

credentials), press the Reset button for 5 seconds.

Andere Handbücher für IOT8EUSBREF-1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Semtech Controller Handbücher

Semtech

Semtech TS8000 Flash Series Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung