Sena 10C EVO Bedienungsanleitung

10C Evo

10C Evo Manual

Motorcycle Bluetooth Communication & Camera System

1. Turning On/Off the Headset

To power on the headset, press the Jog Dial and the Phone Button at the same time until the blue LED

appears. To power off the headset, press the Jog Dial and the Phone Button at the same time until the

red LED appears briefly.

2. Adjusting Volume

You can easily adjust the volume by rotating the Jog Dial.

3. Checking the Battery Level

When the headset is powering on, the red LED flashes rapidly indicating the battery level.

4 flashes = High, 70~100%

3 flashes = Medium, 30~70%

2 flashes = Low, 0~30%

When you power on the headset, keep pressing the Jog Dial and the Phone Button simultaneously for

about 3 seconds until you hear high tone triple beeps. Then you will hear a voice prompt indicating the

battery level is high, medium, or low.

4. Charging the Battery

You can charge the headset by connecting the supplied USB power & data cable into a computer’s USB

port or USB wall charger. The LED turns red while the headset is charging and turns blue when it is fully

charged. It takes about 3.5 hours to be completely charged.

5. Pairing with Mobile Devices - Phone, Music

1. Press and hold the Phone Button for 5 seconds until the LED flashes red and blue alternately and you

hear multiple beeps.

2. Search for Bluetooth devices on your mobile phone. Select the Sena 10C Evo in the list of the devices

detected on the mobile phone.

6. Using Phone Features

Answering Calls: Tap the Phone Button or the Jog Dial to answer the call.

Ending Calls: Tap the Phone Button or press the Jog Dial for 2 seconds until you hear a beep

Rejecting Calls: Press the Jog Dial for 2 seconds until you hear a beep while the phone is ringing.

Transferring Calls: Press the Phone Button for 2 seconds until you hear a beep.

7. Listening Music

Playing or Pausing Music: Press and hold the Jog Dial for 1 second until you hear a double beep.

Tracking Forward and Backward: Rotate while pressing the Jog Dial clockwise or counter clockwise.

8. Pairing with Other Headsets

The 10C Evo can be paired with up to three other headsets for Bluetooth intercom conversation.

1. Press and hold the Jog Dial of the headset A and B for 5 seconds until red LEDs of the both units start

to flash rapidly.

2. Simply tap the Jog Dial of any one of the two headsets A and B, and wait until the LEDs of both

headsets turn to blue and intercom connection is automatically established.

9. Using the Intercom

You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single

tap to intercom with the first intercom friend, double tap to intercom with the second intercom friend, and

triple tap to intercom with the third intercom friend.

10. Turning On/Off the Camera

To turn on the camera, tap the Camera Button. The camera turns off automatically after five minutes of

inactivity. To turn off the camera manually, tap the Camera Button and the Phone Button simultaneously.

11. Recording Videos

To record a normal video, set the video mode setting in the camera configuration to be video mode. Press

and hold the Camera Button for 1 second to start video recording. The green LED will flash. Press and

hold the Camera Button for 1 second to stop recording.

12. Taking Photos

Tap the Camera Button to take a photo. The green LED will flash and you will hear a shutter sound.

13. Turning On/Off the FM Radio

To turn on the FM radio, press and hold the Phone Button for 2 seconds until you hear a mid-toned

double beep sound.

14. Seeking Stations

Rotate while pressing the Jog Dial clockwise to search up the station dial or counter clockwise to search

down the station dial.

15. Listening to Preset Stations

Tap the Phone Button once to go upward to your next saved preset station.

16. Saving or Deleting Stations

1. To save the current station, press and hold the Jog Dial for 2 seconds until you hear a voice prompt,

“Preset (#)”.

2. Rotate the Jog Dial clockwise or counter clockwise, in order to select which preset number you want for

that specific station.

3. To save the current station, tap the Jog Dial again. You will then hear a voice prompt, “Save preset (#)”.

4. To delete the saved station in the preset number, tap the Phone Button. You will then hear a voice

prompt “Delete preset (#)”.

17-1. Settings

To enter into voice configuration menu, press and hold the Jog Dial for 10 seconds until the LED shows

solid blue and you hear high toned double beeps.

To enter into camera configuration menu, press and hold the Camera Button for 8 seconds until you hear

a voice prompt, “Camera setup”.

18. Factory Reset

If you want to restore the 10C EVO to factory default settings, press and hold the Phone Button for 10

seconds. Tap the Jog Dial. The headset automatically restores the default settings and turns off.

19. Installing the headset on your Helmet

Using the Clamp Unit

1. Loosen the two screws on the back plate of the clamp unit with the

included allen wrench.

2. Insert the back plate of the clamp unit between the internal

padding and external shell of the left side of the helmet.

3. Tighten the two screws until the clamp unit is fastened firmly to

the helmet.

4. Insert a microSD card into the card slot to use camera.

5. Attach the main unit to the clamp unit until you hear a click.

Note: This device can be weared on the head of human with separation distance of 5mm

FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

FCC ID：S7A-SP59

IC Caution:

- English:

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

- French:

Le présentappareilestconformeaux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitationestautorisée auxdeux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le

brouillageest susceptible d'encompromettre le fonctionnement.

IC：8154A-SP59

Andere Handbücher für 10C EVO

Inhaltsverzeichnis

Andere Sena Konferenzsystem Handbücher

Sena

Sena 30K Bedienungsanleitung

Sena

Sena 10Upad Bedienungsanleitung

Sena

Sena 50R Bedienungsanleitung

Sena

Sena 10R Bedienungsanleitung

Sena

Sena 50R Bedienungsanleitung

Sena

Sena SF2 Bedienungsanleitung

Sena

Sena 10C EVO for 10C-EVO-01 Bedienungsanleitung

Sena

Sena 5R Lite Bedienungsanleitung

Sena

Sena 10R-02 Bedienungsanleitung

Sena

Sena 10R Bedienungsanleitung

Sena

Sena ACS-RAM Bedienungsanleitung

Sena

Sena SRL-MESH Bedienungsanleitung

Sena

Sena 5S Bedienungsanleitung

Sena

Sena 10U Bedienungsanleitung

Sena

Sena SFR Bedienungsanleitung

Sena

Sena SRL-EXT Bedienungsanleitung

Sena

Sena SMH10R Bedienungsanleitung

Sena

Sena TUFTTALK Bedienungsanleitung

Sena

Sena 10s Bedienungsanleitung

Sena

Sena SPIDER RT1 Bedienungsanleitung

Sena

Sena 10s Bedienungsanleitung

Sena

Sena 3S PLUS Bedienungsanleitung

Sena

Sena SPIDER ST1 Bedienungsanleitung

Sena

Sena TUFFTALK M Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung