Sena SP53 Bedienungsanleitung
Prism Tube WiFi Instruction
1. Basic Operation
1.1 Turning the Camera On or Off
On Off
Note
• Recording will start shortly after the camera is turned on. Recording stops shortly
before the camera is turned off.
• A microSD card must be inserted to record video.
1.2 WiFi on/off
After powering on, WiFi initializes and turns on. If you are not using WiFi in 3 minutes,
WiFi will be turned off.
There is no way to turn only WiFi on or off. If the WiFi is turned off with the Prism Tube
WiFi on, you have to power off it and on again.
Note
- If you do not see the preview after starting recording by watching the app, the
WiFi will turn off in 3 minutes.
- If you are not using the app after changing the camera settings with the app, the
WiFi will turn off in 3 minutes after you change the settings.
- WiFi will turn off if you do not change the settings in 3 minutes, while the app is
connected.
When configuring with App, communication is not continuously performed during
setting. Therefore, if there is no input for 3 minutes regardless of whether the screen
turns off, WiFi turns off.
1.3 Switching Between Normal Recording and Loop
Recording
While the camera is turned on, press the SD Card Format Button for 1 second to switch
between normal recording mode and loop recording mode.
Note
The Blue LED blinks once during normal recording and twice during loop recording.
2. Battery
Checking the Battery Level
Turn on the camera and check the battery level via the Status LED.
Low Battery Warning
Charging the Battery
3. Firmware Upgrade
To install the latest firmware of the camera, follow the directions below.
1) Turn off the camera and connect it to your PC via a USB cable.
2) Download the latest firmware from www.sena.com.
3) Move the downloaded firmware file into the root folder of
the storage device (MicroSD Card)
4) Connect to the root folder of the storage device (MicroSD Card)
5) Disconnect the camera from the PC
6) The update will be executed automatically when you turn on the camera.
At this time, the camera LED blinks green and the camera LED turns red to
indicate steady state.
7) Turn off the camera and Turn on the camera.
4. Memory Card
4.1 Formatting the Memory Card
To format the memory card, turn on the camera and press and hold the SD Card Format
Button for 10 seconds until the LED alternates red and blue.
Note
It is recommended to format the SD Card using this method. You can format the SD
Card using a PC or App
5. Transfer
Transferring Video Files
Note. Turn off the camera and connect it to your PC via a USB cable. Your PC should recognize
the camera as a removable device.
6. CONFIGURATION SETTINGS
the camera configuration menu, you can change the
settings of the Prism Tube WiFi through the the Sena Camera App.
7. TROUBLESHOOTING
7.1. Fault Reset
If the Prism Tube is not working properly for any reason, push the pin-hole reset button
located on the back of the camera while it is turned on.
7.2. Factory Reset
To factory reset , turn on the camera and press and hold the SD Card Format Button for
5 seconds until the red LED flash.
Safety Precautions
Please ensure that the product is properly used by observing the warnings and cautions
below to prevent any risk and/or damage to property.
Product Storage and Management
• Keep the product free of dust. It may damage mechanical and electronic parts of the
product.
• Do not store the product in high temperatures as this may reduce the life span of electronic
devices, damage the battery, and/or melt plastic parts of the product.
• Excessive heat (e.g. exhaust heat) can cause damage to the decoration, the inner shell of
the helmet and the interior lining.
• Do not store the product in cold temperatures. Abrupt changes in temperatures may cause
condensation and damage electronic circuits.
• Do not clean the product with cleaning solvents, toxic chemicals, or strong detergents as
this may damage the product.
• Direct contact with motor fuel, thinners or solvents can destroy the structure of the inner
and outer shell. Make sure the helmet does not come into contact with such substances,
even for cleaning purposes.
• Do not paint the product. Paint may obstruct moving parts or interfere with the normal
operation of the product.
• Do not drop or otherwise shock the product. It may damage the product or its internal
electronic circuits.
• Do not disassemble, repair or modify the product as this may damage the product and
invalidate the product warranty.
• Do not store the product in humid environments, especially for long time storage.
• The helmet should be replaced after 5 to 7 years, depending on use and care. Although the
outer shell is in principle capable of a longer service life, the occurrence of material fatigue
and wear to other components, as well as the overall action of the helmet and the unknown
conditions in which the helmet has been used, make it advisable for your own safety to
replace the helmet after this period of use.
• Original components (in particular on the outer shell, inner shell and restraint system)
should not be altered or removed. The fitting of additional parts from other manufacturers
that have not been recommended can reduce the protective effect and renders the DOT
certification and all warranty and insurance claims invalid.
• Use only original parts, replacement parts and accessories that Sena has expressly
approved for your helmet.
Product Use
• Motorcycling is associated with particular risks and dangers for the rider and passenger.
These risks and dangers can be reduced, but not eliminated completely, by wearing a
helmet. It is impossible to state precisely what the protective effect of a helmet will be in the
event of an accident. Safe riding techniques, adapted to the particular road and weather
conditions, are essential for your safety.
• To provide adequate protection, the helmet must fit well and be securely fastened.
• Always fasten the chinstrap before setting off and check that the fastening system and
strap are correctly in position.
• Never ride with the chinstrap unfastened or incorrectly adjusted. The chinstrap must be
correctly
positioned and must not come loose when pulled. The fastener is not correctly closed if the
chinstrap becomes loose when pulled.
• The full protective function of a helmet can no longer be guaranteed after an accident or
impact. Like the crumple zone of a car, the impact energy of a collision is absorbed by
complete or partial destruction of the structure of the outer and/or inner shell of the helmet.
Because of the way helmets are designed, this damage is rarely visible from the outside.
The safety helmet is designed to absorb only one impact. It is therefore essential to replace
the helmet after a fall, accident or other violent impact. For safety reasons, the old helmet
should be rendered unusable.
• The helmet safety mechanism described above can also cause small cracks in the shell
when the helmet is dropped from a small height (less than 1 meter).
• Any helmet that has been subjected to a violent impact should be replaced.
• No helmet provides absolute protection from all conceivable impacts. This helmet has been
specially developed for motorcycle riding and is unsuitable for other purposes.
• Examine the helmet for damage at regular intervals. Small scratches will not impair the
protective function of your helmet.
• In some regions, it is prohibited by law to ride motorcycles while wearing headsets.
Therefore be
certain to comply with all relevant laws in the region before using the product.
• Use of the product at a high volume for a long period of time may damage your eardrums
or hearing ability. Keep the volume at a modest level to prevent damage.
• Do not cause impact to the product or touch it with sharp tools as this may damage the
product.
• Do not use the product in high-temperatures or apply heat to the product as this may cause
damage, explosion, or fire.
• Keep product away from pets or small children. It may damage the product.
• In any place where wireless communication is prohibited, such as hospitals or airplanes,
turn off the power and refrain from using the product. In a place where wireless
communication is prohibited, electromagnetic waves may cause hazards or accidents.
• Do not use the product near hazardous explosives. When it is near any explosion hazards,
turn off the power and heed any regulations, instructions, and signs in the area.
Battery
This product has an irreplaceable rechargeable battery inside. Therefore, when using the
product, make sure to adhere to the following:
• Never separate the battery from the product as this may damage the product.
• The battery performance may be reduced over time with usage.
• In recharging the battery, make sure to use an approved charger provided by the
manufacturer. Use of a non-approved charger may cause fire, explosion, leakage, and other
hazards may also reduce the life time or performance of the battery.
• Any 3rd party USB charger can be used with Sena products if the charger is approved by
either the FCC, CE, IC or other locally approved agencies that Sena accepts.
• Store the battery at temperatures of 15°C~25°C (59°F~77°F). Higher or lower temperatures
may
reduce the capacity and life of the battery, or may cause temporary non-operation. Do not
use the
product in sub-zero temperature, because it may cause serious reduction of the battery
performance.
• If you apply heat to the battery or throw it into a fire, it may explode.
• Do not use the product with a damaged battery. It may explode and/ or cause accidents.
• Never use a damaged charger. It may explode and/or cause accidents.
• Battery life may vary depending on conditions, environmental factors, functions of the
product in use, and devices used with it.
Certification and Safety Approvals
FCC Compliance Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a digital device
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment on and off, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. The antenna used for this transmitter must not transmit
simultaneously with any other antenna or transmitter, except in accordance with FCC multi-
transmitter product procedures.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void user’s authority to operate the equipment.
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
The distance between the antenna of the device and the head surface is at least 53.6mm
and use 53.6mm or more.
La distance entre l'antenne de l'appareil et la surface de la tête est d'au moins 53,6 mm et
d'utiliser 53,6 mm ou plus..
WEEE (Waste Electrical and Electronic Equipment)
The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that
all electrical and electronic products, batteries, and accumulators must be taken to separate
collection at the end of their working life. This requirement applies to the European Union
and other locations where separate collection systems are available. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please do not
dispose of these products as unsorted municipal waste, but hand it in at an official collection
point for recycling.
DOT Certification
This product conforms to the DOT FMVSS 218 (US) helmet safety standards as defined by
the United States Department of Transportation Federal Motor Vehicle Safety Standard. This
certification applies to the United States of America. The approval label can be affixed
permanently to the outside of the helmet (United States, Argentina, Australia and others). Do
not remove or attempt to remove the approval label from the helmet. Do not affix approval
labels of unknown origin to the helmet. These are more than likely counterfeit labels. It is
against the law to affix counterfeit labels to helmets. If you are in any doubt over the origin of
the approval label affixed to your helmet contact Sena directly, and not your dealer.
Product Warranty and Disclaimer
Limited Warranty
Sena Technologies, Inc. (“Sena”) guarantees the product quality based on the technical
specification stated in the product manual, and data regarding product warranty. Here,
product warranty extends to the product only. Sena will not be liable for any loss, damage of
human life, or loss of property which may result from using the product beyond defective
parts or flaws that occur due to problems in manufacture.
Warranty Period
Sena guarantees free-of-charge repair or replacements of defective parts of the product or
flaws that may have occurred due to problems in manufacture for a period of 5 years for the
helmet and 2 years for the electronic parts. Each period starts from the date of the initial
purchase. The limited warranty extends only to the original consumer purchaser of the
product and is not assignable or transferable to any subsequent purchaser/end-user.
Termination
Quality warranty of the product becomes effective on the date of initial purchase. In addition,
the quality warranty of the product expires when the warranty period expires. However, in
the following cases, the warranty will be terminated prematurely.
• In the event the product has been sold or transferred to a third party.
• In the event the manufacturer's name, serial number, product label, or other markings have
been modified or removed.
• In the event any unauthorized person has tried to disassemble, repair, or modify the
product.
Notice and Waiver
By buying and using this product, you relinquish considerable legal rights including any claim
for compensation for damages. Therefore, be certain to read and understand the following
terms and conditions before using the product. Use of this product will constitute consent to
this agreement, and forfeiture of rights to all claims. If you do not consent to all the terms and
conditions of this agreement, return the product for a refund.
1. You agree that you, your descendants, legal proxies, successors, or transferees will not
raise permanent volitional request for any suit, claim, implementation, redemption or similar
action from Sena with regard to any occasion such as difficulty, pain, suffering,
inconvenience, loss, injury, or death which may occur to you or a third party during the use
of this product.
2. You must completely understand and accept all risks (including those occurring due to
any careless behavior of yours or others) which may occur during the use of this product.
3. You are responsible for ensuring that your medical condition permits usage of the product
and that you are in sufficient physical condition for using any device which can be used with
Inhaltsverzeichnis
Sprachen:
Andere Sena Digitalkamera Handbücher
