SENAO SL-2511SR Bedienungsanleitung
Senao
2-Port Switch Wireless Router
UserGuide
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
Model No. SL-2511SR
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted
in any form or by any means, mechanical, magnetic, electronic, optical, photocopying,
manual, or otherwise, without the prior written permission.
Trademarks
All product, company, brand names are trademarks or registered trademarks of their
respective companies. They are used for identification purpose only. Specifications are
subject to be changed without prior notice.
-1-
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against radio interference in a commercial environment. This
equipment can generate, use and radiate radio frequency energy and, if not installed and
used in accordance with the instructions in this manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
interference, in which case the user, at his own expense, will be required to take whatever
measures are necessary to correct the interference.
CE Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic compatibility,
EN 55022/A1 Class B, and EN 50082-1. This meets the essential protection requirements
of the European Council Directive 89/336/EEC on the approximation of the laws of the
member states relation to electromagnetic compatibility.
-2-
Table of Contents
Chapter 1 Introduction...............................................................................4
Functions and Features.........................................................................4
1.2 Packing List....................................................................................5
Chapter 2 Hardware Installation................................................................6
2.1 Panel Layout...................................................................................6
2.2 Procedure for Hardware Installation ..............................................8
Chapter 3 Configuring Wireless Access Point.........................................11
3.1 Start-up and Log in.......................................................................11
3.2 System Info...................................................................................13
3.3 Toolbox.........................................................................................14
3.4 Primary Setup...............................................................................15
3.5 DHCP Server................................................................................18
3.6 MAC Address Control..................................................................20
Appendix A TCP/IP Configuration for Windows 95/98..........................23
A.1 Install TCP/IP Protocol into Your PC..........................................23
A.2 Set TCP/IP Protocol for Working with This Device....................25
A.3 Specifications...............................................................................32
A.4 Regulatory Compliance Information...........................................34
-3-
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Wireless Access Point. This product
is specifically designed for Small Office and Home Office needs. It provides a solution for
building a LAN and sharing resources with or without wire, and is easy to configure and
operate even for non-technical users. Instructions for installing and configuring this
product can be found in this manual. Before you install and use this product, please read
this manual carefully for fully exploiting the functions of this product.
Functions and Features
High speed for wireless LAN connection
11Mbps data rate by incorporating Direct Sequence Spread Spectrum (DSSS).
Roaming
Provides seamless roaming within the IEEE 802.11b WLAN infrastructure.
IEEE 802.11b compatible
Allowing inter-operation among multiple vendors.
Auto fallback
11M, 5M, 2M, 1M data rate with auto fallback.
Auto-sensing Ethernet Switch
Equipped with a 2-port auto-sensing Ethernet switch.
DHCP server supported
All of the networked computers can retrieve TCP/IP settings automatically from
this product.
Web-based configuring
Configurable through any networked computer’s web browser.
-4-
MAC Address Access Control supported
Allows you to assign different access right for different users.
Firmware Upgradable
Provides firmware upgrade via Web Browser or Windows Application.
1.2 Packing List
Wireless Access Point unit
Installation CD-ROM
Power adapter
CAT-5 UTP Fast Ethernet cable
-5-
Chapter 2 Hardware Installation
2.1 Panel Layout
2.1.1. Front Panel
Figure 2-1 Front Panel
LED:
LED Function Color Status Description
POWER Power indication Green On Power is being applied to this
product.
M1 System status 1 Orange Blinking This product is functioning
properly.
WLAN Wireless activity Green Blinking Sending or receiving data via
wireless
On An active station is connected to
the corresponding LAN port.
Link/Act.
1~2 Link status Green Blinking The corresponding LAN port is
sending or receiving data.
10/100 Data Rate Green On Data is transmitting in 100Mbps
on the corresponding LAN port.
Port:
RESET To reset system settings to factory defaults, please follow the steps:
1. Power off the device,
2. Press the reset button and hold,
3. Power on the device,
4. Keep the button pressed about 5 seconds,
5. Release the button,
6. Watch the M1 LED, they will flash 8 times and then M1 flash once
-6-
per second.
-7-
2.1.2. Rear Panel
Figure 2-2 Rear Panel
Ports:
Port Description
12VDC Power inlet: DC 12V, 1.5A (minimum)
Port 1-2 the ports where you will connect networked computers and other
devices.
Connector TNC connector
RS-232 RS-232 for ISDN/TAmodem
2.2 Procedure for Hardware Installation
1. Decide where to place your WirelessAccess Point
You can place your Wireless Access Point on a desk or other flat surface, or you can
mount it on a wall. For optimal performance, place your Wireless Access Point in the
center of your office (or your home) in a location that is away from any potential
source of interference, such as a metal wall or microwave oven.
-8-
2. Setup LAN connection
a. Wired LAN connection: connect an Ethernet cable from your computer’s Ethernet
port to one of the LAN ports (number 1-2) on the AP. Repeat the process to
connect other computers to the AP. If you need to connect more than two
computers to the AP, use a 10/100 Fast Ethernet switch (preferred) or hub and
connect the Ethernet cable from the AP to the switch/hub’s UPLINK port. You
may need to switch on the UPLINK feature on the switch/hub. The AP supports
up to 253 network computers and devices.
b. Wireless LAN connection: locate this product at a proper position to gain the best
transmits performance.
Figure 2-3 Setup of LAN connections for this product.
Note: If an UPLINK port is not available, simply connect a
crossover Ethernet cable from theAP to the switch/hub.
-9-
Inhaltsverzeichnis
Andere SENAO WLAN-Router Handbücher
