Senect AQUACULTURE Series Bedienungsanleitung

Product type

Product

name:

SENECT®AQUACULTURE|CONTROL

150 W / 300 W

Versions:

AQUACULTURE|CONTROL –Basic (150 W)

AQUACULTURE|CONTROL –Basic (300 W)

AQUACULTURE|CONTROL –Pro (150 W)

AQUACULTURE|CONTROL –Pro (300 W)

Type:

AQC-A1-333-150

AQC-A1-333-300

AQC-A1-663-150

AQC-A1-663-300

Producer:

SENECT GmbH & Co. KG

An 44 –No. 11

76829 Landau / Germany

Important note:

Please read this manual carefully and store it so that you can use it later. Read the warning and safety

notes attentive.

More information and latest software releases or documents can be downloaded from:

www.senect.de

Further information, application descriptions and answers to frequently asked questions can

be also found on the SENECT Forum:

http://forum.senect.de/phpbb/

Table of contents

Product type............................................................................................................................................ 2

Table of contents..................................................................................................................................... 3

Used symbols and wording ..................................................................................................................... 4

General Security Notes............................................................................................................................ 4

Intented use ............................................................................................................................................ 5

Performance specification....................................................................................................................... 6

Getting started ........................................................................................................................................ 7

Scope of delivery ................................................................................................................................. 7

Installation and start-up...................................................................................................................... 7

Using the AQUACULTURE|CONTROL to switch outputs as a function of sensor measurements ...... 9

Controlling the drum filter with the AQUACULTURE|CONTROL....................................................... 11

Using the AQUACULTURE|CONTROL to switch outputs as a function of sensor measurements –

Short version ..................................................................................................................................... 16

Controlling the drum filter with the AQUACULTURE|CONTROL –Short version ............................. 17

Operation .............................................................................................................................................. 19

Display and symbols.......................................................................................................................... 19

Buttons and menu............................................................................................................................. 20

The Menu .............................................................................................................................................. 22

Filter settings..................................................................................................................................... 26

Sensor Menu ..................................................................................................................................... 30

Menu output ports and 230 V AC plugs............................................................................................ 32

Description of the major output functions ....................................................................................... 33

Additional functions .......................................................................................................................... 37

Menu WLAN ...................................................................................................................................... 40

Menu System Settings....................................................................................................................... 46

Technical data ....................................................................................................................................... 48

Information about the correct disposal ................................................................................................ 48

Guarantee.............................................................................................................................................. 48

Used symbols and wording

DANGER!

Warning of life threatening dangers.

WARNING!

Warning of possible life threatening and / or severe irreversible

injuries.

ATTENTION!

Warning of possible medium or slight injury.

ATTENTION!

Follow the notes to avoid damage of equipment.

NOTE!

Further information for the use of the device.

NOTE!

Further information for the use of the device.

General Security Notes

The SENECT® AQUACULTURE|CONTROL is an electronic control unit developed for measuring

and controlling water quality parameters and actuator like fish feeders, valves or drum filters.

Since it is an electric product the common prerequisites for a safe instrument usage

must be fulfilled. The device must be operatated with 230 V AC (~50 Hz). Ensure

that all cables are installed safely so that no obstacles for persons are built and all.

Mount all cables and electric devices protected against direct environmental

impacts like overheating by direct sunlight and water. Even if the product is

protected against spray water, the product´s lifetime will be elongated, if it is

mounted on a protected place.

For many applications a ground fault circuit interruper (interrupting current <= 30 mA) is

required by law. Inform yourself about the valid legislation. If the mains plug cable is damaged,

only the producer or a qualified person designated by the producer is allowed to repair the

damage.

Intented use

The operating temperature of the device must be between 0°C and +40°C. It is not allowed to

modify the SENECT® AQUACULTURE|CONTROL, to open the housing or to insert anything into

the housing.

If the power cable is damaged, it must be replaced by the producer or a qualified person

designated by the producer to avoid potential dangers.

The device is designed to be operated by professional users. It can be also operated by

children over the age of 8 years and persons with limited physical, sensorial or cognitive

ability, if they are supervised, trained in the operation of the device, able to operate the device

safely and if they understand potential risks resulting from the operation. It is for children or

persons with limited physical, sensorial or cognitive ability not allowed to perform any

maintenance works.

Please store this manual. We suggest the storage a copy of the manual in the vicinity of the

device.

Technical and optical changes of this manual are subject to alterations.

Warning: Before doing any maintenance work switch off all electric devices or unplug

the mains plug.

Intented use

The AQUACULTURE|CONTROL is an electronic control and measurement unit developed to

measure water quality parameters and control processes in professional industrial

aquaculture facilities.

Performance specification

The SENECT AQUACULTURE|CONTROL is a versatile measurement and control unit designed

for the use in aquaculture. There are four different versions available:

AQUACULTURE|CONTROL

Basic

150 W

Basic

300 W

Pro

150 W

Pro

300 W

Sensor input ports

Actuator output ports

2 (max. 1 A)

5 (max. 1 A)

24 V DC PWM, 4-

20 mA, 0-10 V

24 V DC PWM, 4-

20 mA, 0-10 V

24 V DC PWM, 4-

20 mA, 0-10 V

24 V DC PWM, 4-

20 mA, 0-10 V

High-power-

actuator output ports

1 (max. 5 A)

1 (max. 10 A)

1 (max. 5 A)

1 (max. 10 A)

24 V DC PWM

230 V AC mains plug

(max. 8 A, 2 A, 4 A)

Every type of SENECT sensor can be connected to the universal sensor input ports (e.g. the

oxygen sensor O2S, the pH sensor XR-1 or the water level probe PS). The

AQUACULTURE|CONTROL measures then the signal of the connected sensors, saves the

measurements internally (up to max. 3 months) and can control output ports depending on

the sensor readings or send alarm message, if the control unit is connected to the internet.

At its actuator output ports, 24 V DC actuators like valves or fish feeders can be connected

directly. Also actuators, which can be controlled via 4-20 mA or 0-10 V control signals can be

controlled directly. Actuators with 230 V AC can be switched with the actuator ports by using

the optional PowerSwitch SC24-230 or can be controlled directly, when they are connected to

one of the three 230 V AC output ports at the bottom side of the device. Please consider

always the max. allowed power consumption of actuators.

The AQUACULTURE|CONTROL can also be used to control drum or belt filters. Pleas consider

here:

The direct control of drum or belt filters is only possible for filter with a 24 V DC filter

motor with max. 5 A (AQC-A1-xx3-150) or 10 A (AQC-A1-xx3-300) or with a 230 V AC

filter motor. The spray pump must be operated with 230 V AC with a maximal

current of 8 A. For enabling all functions which need to adjust the motor speed of the filter

(e.g. intensive cleaning), 230 V or 400 V filter motors must be controlled via a variable

frequency drive connected to one of the actuator output ports (see Fig. 5).

Getting started

The integrated WLAN module can be used to embed the SENECT AQUACULTURE|CONTROL

into a WLAN network. With an established internet connection of the

AQUACULTURE|CONTROL, the control unit can download software updates and send alarm

messages. Additionally, with the SENECT Control App on an Android, Apple iOS or Windows

device, the AQUACULTURE|CONTROL can be operated remotely (Internet connection with

port forwarding and dynamic DNS necessary, for more details see chapter WLAN).

Please consider during the design of your control system that the sensors, cables and

actuators are not within the scope of delivery of the AQUACULTURE|CONTROL and have to

be ordered separately.

Getting started

Scope of delivery

o1 x AQUACULTURE|CONTROL unit with 3 m power cable

o1 x Wall mount set

o1 x Set of exchange fuses with 2 AT, 4 AT and 8 AT

o1 x Manual

Note

Please check directly after delivery, that the package is not destroyed or damaged

or was opened before. Please check also, that all parts as listed above are included.

If anything is missing or broken, please contact us as soon as possible within 14 days.

Unfortunately, we cannot accept later information of damage, which happened during the

transport.

Installation and start-up

Choose a place for your AQUACULTURE|CONTROL which is clean, dry and protected

from direct sunlight. Ensure that all cables are placed safely and all regulations are

fulfilled.

To mount the AQUACULTURE|CONTROL, place the delivered wall mounting parts on the back

of the device. Tight the parts with the delivered screws (3 x 10 mm, see Fig. 1). Afterwards,

you can use the wall mounting parts of the AQUACULTURE|CONTROL to attach the device to

its place, e.g. on a wall.

Plug the 230 V power plug of the AQUACULTURE |CONTROL in a spray water protected plug

(IPx4 or higher) but do not switch the AQUACULTURE |CONTROL on yet. The next steps inform

you how to connect the sensors and actuators.

Getting started

Fig. 1: Wall mounting parts and dimensions of the drill holes for the mounting of the AQUACULTURE|CONTROL.

Fig. 2: Sensor and actuator ports of the AQUACULTURE|CONTROL Pro. The AQUACULTURE|CONTROL Basic is equipped

without the upper row (SENSOR 4-6 and OUT 4-6).

Getting started

Using the AQUACULTURE|CONTROL to switch outputs as a function

of sensor measurements

Which sensors, which actuators and how the cables are conneced depend strongly on your

application. In general, you can follow these steps:

1. Mount sensors and actuator at their location.

2. Place and lay the cables safely to the AQUACULTURE|CONTROL, remove the

protection cap from the sensor input port and connect the sensor plug to the blue

marked „SENSOR“ input.

3. Switch on the AQUACULTURE|CONTROL and set the desired settings. To switch the

output ports, you have to assign a function to the selected output port.

Fig. 3: View from the bottom side of the AQUACULTURE|CONTROL.

Note: Changing languages can be easiliy done in the menu. Press the button MENU

and select under „System Einstellungen / Sprache“ the language „English“.

Getting started

Application example: Oxygen control

In this example, the oxygen sensor O2S is connected to SENSOR 1 and the „normally opened“

solenoid valve (Type: MVO-M7-SC, Art. No.: 3020) is plugged into actuator plug OUT 1.

(„Normally open“ is selected here, that in case of a power shutdown the valve opens

automatically and the fish still get oxygen.)

The desired oxygen level should be over 95% and if 100% are reached, the addition of oxygen

shall be stopped. Go to the menu (MENU / Output Ports / Plug 1) and set:

Function: Sensor Control –a new submenu appears (when you go back in the

menu)

In the submenu „Sensor Control“ set:

oControl Parameter: O2 % a.s.

oSensor Plug: 1

oStart value: 95%

oStop value: 100%

oMax. Duration: 00:00:00

oBreak Time: 00:00

In the submenu „Output signal“ set:

oPolarity: Low Active (the output is switched off, when the O2

concentration falls below 95% so that the [normally open] valve opens)

Now, all the settings are done and you can test the system, e.g. dipping the O2S sensor in

0-%-oxygen solution.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Senect Steuereinheit Handbücher

Senect

Senect FILTER CONTROL Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung