Sengled A01-A60 Bedienungsanleitung

User Manual

A01-A60 LED Lamp

LED + Wi-Fi REPEATER

Features

Install like any other light bulb. Easy to setup and enjoy the extended Wi-Fi

signal coverage evenly.

Supports two Wi-Fi network mode: Access Point (AP) / Repeater

Two build-in antennas for high throughput data exchange rate of maximum

300Mbps

Compatible with most smart phones, tablets and computers that support Wi-Fi

IEEE 802.11b/g/n standard at 2.4GHz.

Remote LED lights ON/OFF and dimming control individually or by group

Download the free Boost Android or iOS App to explore even greater

functionality

Box Contents

One A01-A60 Bulb

User Manual

Limited Written Express Warranty

Product Specifications

Power Supply: 100~230V AC, 50/60Hz

Lamp Socket: E26/E27/B22

Power Consumption: 7.4W (LED + Wi-Fi Repeater), Peak 9W

Operating Temperature: -20°C ~ +40°C

Store Temperature: -40°C ~ +70°C

Operating Humidity: 10% ≤ RH ≤ 95%, Non condensation

Atmospheric Pressure: 86kPa ~ 106kPa

Colour: Neutral White

Dimensions: 120mm (H) x Φ60mm (Dia.)

Weight: 290g (approx.)

Spécifications de produit (par ampoule)

• Alimentation: 100 ~ 230V AC, 50/60 Hz

• Douille: E26 / E27 / B22

• Consommation d’énergie: 7.4W (LED + Wi-Fi Répéteur), Peak 9W

• Température de service: -20 °C à + 40 °C

• Stocker Température: -40 °C à + 70 °C

• Humidité de fonctionnement: 10% ≤ HR ≤ 95%, sans condensation

• Pression atmosphérique: 86 kPa ~ 106 kPa

• Couleur: Blanc neutre

• Dimensions: 120mm (H) x 60mm Φ (. Dia)

• Poids: 290g (environ).

LED Lights

Power: 6 Watts

Luminance: 470 lumens

Light Beam Angle: 240 degrees

Colour Temperature: 3000K - Warm White

CRI: 80

Dimming: Yes (Do not use with external or outside dimmers. APP SOFTWARE

DIMMING CONTROL)

Ampoules à LED

• Puissance: 6 Watts

• Luminance: 470 lumens

• Angle du faisceau lumineux: 240 degrés

• Température de couleur: 3000K - Blanc chaud

• CRI: 80

• Dimming: Oui ( Ne pas utiliser avec des variateurs de lumière ou à l'extérieur

APP LOGICIEL de commande de gradation)

Wi-Fi Repeater

Wi-Fi Standard: IEEE 802.11b/g/n

Wi-Fi Transmitter Frequency Range: 2.412 - 2.462 GHz

Power: 1.8 Watts (Standby), 2.8 Watts (Full load)

2T2R MIMO wireless technology

Security Mode: 64/128 bit WPA-PSK/WPA2-PSK, WPA/WPA2

Encryption Type: WEP64/WEP128/TKIP/AES

Wi-Fi Transmitter power:

@ 802.11b: +15dBm (Max)

@ 802.11g: +15dBm (Max)

@ 802.11n: +17dBm (Max)

Wi-Fi Receiver power:

@ 802.11b: -89dBm

@ 802.11g: -81dBm

@ 802.11n: -71dBm

Distance Range between Router and A01-A60 Bulb: 115 feet (near line of

sight)

SENGLED, Incorporated, registered in the United States and other countries. Specifications are

subject to change without notice. Apple, iPhone, iPad, iPod, iPod touch and Retina are

trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air, iPad mini and

Lightning are trademarks of Apple Inc. Other Trademarks and trade names are the property of

their respective owners.

INSTALLATION INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE

BACK COVER OR TAKE APART. THERE ARE NO SERVICEABLE PARTS INSIDE.

1. Before installing the Boost into an E26/E27/B22 light bulb socket, turn the

light switch to the OFF position. (DO NOT USE WITH EXTERNAL OR OUTSIDE

DIMMERS).

2. Screw the bulb into an E26/E27/B22 socket and turn the power on.

3. On the portable smart device (e.g. smartphone or tablet), make sure WLAN is

turned on and has been connected to the wireless router with a proper

passport.

4. Search for the “boost by Sengled” for corresponding operating system,

download and install it on a portable smart device:

Get App from Google Play Store for Android Devices;

5. Launch the boost by Sengled application, and a 'Welcome' page appears. At

the beginning, press the "network" tab to initialize boost A01-A60 bulb's

configuration. After that, click the “START” button to enter the configuration

and control interface of the bulb/s.

6. The App will search and list out nearby available wireless router/s

automatically. Choose one of the routers as the root router. Type in the

Access Password and press “Next” to move forward.

7. Input the access password which is as the router Wi-Fi router, click “Next” to

enter the Next step. At this point, APP will send multicast to make the lamp of

the Factory Settings is connected to the root router, and the program will search

out these lamps. The names of these lamps apply their MAC address the name of

the last two as a suffix, and display them on the interface for users to choose

whether to access the network.

If there is no any equipment, please check if the lamp is powered on, and click

the refresh button to try again.

8. The App will also search and list out nearby available boost A01-A60 bulb/s.

The default SSID of the bulb is “SENGLED_AP”. (ATTENTION: Figure shows

below, SSID Name of "LL_AP_00_**" only for engineering samples demo).

Press the “Start” tab for configuring all chosen boost A01-A60 bulbs. And the

lamps which are not chosen restore to the initial state of factory Settings. If

the root router is encrypted, the initialized bulb is also encrypted with a

default password of "12345678". Input the bulb password and wait for the

configuration process complete.

9. After the process of bulb network configuration has been succeeded, boost

A01-A60 bulb/s will reboot (THIS PROCESS MAY TAKE FEW MINUTES, PLEASE

BE PATIENCE). Press “Done” and return to the home page. If the configuration

failed, refresh the configuration to networking again.

10. The App begins to search the configured online LED bulb/s. (SINCE THE BULB

REBOOT PROCESS MAY TAKES FEW MINUTES, PLEASE BE PATIENCE AND

REFRESH THE LIST FROM TIME TO TIME). After searching out all configured

bulbs, the interface shows a Main Control Page. This can be used to control

the overall LED light dimming and ON/OFF.

11. To control the LED bulb individually, pull up the bulb list at the bottom, each

bulb can be dimmed separately. Click the arrow on the right, and it goes to

the bulb wireless network configuration page.

Main page shows that adjust total brightness. The list displays the brightness

of each lamp. The actual brightness is the brightness of each lamp multiplied

by the percentage of the total brightness.

12. Lamp configuration page is read-only mode by default as shown in the

following figure. If need editing the lamp information, click the edit button at

top right corner, and enter the lamp password to edit mode.

Enter the edit mode, basic setup can modify the SSID, the Name of the light, and

set the brightness which the lamp is in power memory last time, so as to recover

after the next to electricity save.

Security Settings change the lamp encrypted and password. Security Settings

page has a button "Removed from the network" which is used to light restore to

factory Settings and removed from the network. Users can use this button to

restore the default lights to networking again.

Under the 'General' tab, the wireless network parameters of the bulb are listed

(such as MAC address). User can change bulb's SSID (listed on the WLAN table,

visible name to public), or Name (listed on the boost by Sengled App) to a more

meaningful name, such as "Living Room AP" or "Living Room Wi-Fi". Press

"Apply" to active such changes.

Under the 'Security' tab, user can change the Encryption Mode, or change the

bulb access Password. Press "Apply" to active such changes.

13. If re-configuration of the wireless network is needed, press the Setting Menu

button on the Main Control Page and click the "Network" tab. Re-initialize all

bulbs on the network and start setup wizard again.

14. If the bulb cannot be detected by the portable smart devices or App in any

ways, user can press the physical RESET button to reset the configuration of

the bulb (in the middle of the LED lens), as shown below.

RESET button

IMPORTANT SAFETY INSTRUCTIONS

• Read and keep these safety instructions.

• Heed all warnings contained within these instructions.

• Please follow all user manual instructions when installing the product.

• Clean SENGLED product only with a dry towel.

• This Product is intended for indoor use only.

• Do NOT use this product outdoors.

• Do NOT get this product wet and do NOT use near any water source.

• The product should not be exposed to dripping or splashing liquids of any kind.

• Do not install the product near any heat sources, such as heater, radiators,

stove, heat registers or other apparatus that produce heat.

• Ensure that the product is stable and secured in place during installation. If the

product is dropped or falls out of the light socket, it may cause bodily harm.

• If the product is dropped or falls out of the light socket, it may be damaged.

Please check the product for any visible damage.

• To reduce the risk of electric shock, do NOT remove the back cover or take

apart. There are no serviceable parts inside.

• To prevent product failure, the bulb should only be installed in operating

environments.

• Do not block any ventilation openings on the product.

• Never push any objects into the openings or slots on the product. Doing so may

create an electric shock or fire hazard.

• Maintain sufficient distance around your product for sufficient ventilation, do

not put anything within at least 6 inches of lightbulb socket.

• For best protection against lightning, unplug the product from its power source

during a storm.

• Only use accessories specifically recommended by the manufacturer.

• Refer all servicing to qualified SENGLED service technician.

• Servicing is required when the product:

1) has been damaged in any way;

2) liquid has been spilled on the product;

3) objects have fallen into the product;

4) the product has been exposed to rain or moisture,

5) the product does not operate normally, or has been dropped.

• Repairs must be performed by a qualified SENGLED technician.

• For bulb with a weight significantly higher than that of the bulbs for which they

are a replacement, the increased weight may reduce the mechanical stability of

certain luminaires and bulb holders and may impair contact making and bulb

retention. Check that all sockets and bulb holders frequently and make sure they

are secure and stable.

• The bulb can be hot and should not be touched without taking care.

CAUTION: INDOOR OPERATIONS ARE ONLY ALLOWED

NOT FOR USE IN EMERGENCY LIGHTING.

BE SUITABLE FOR DAMP LOCATIONS.

ENSURE FIXTURE CAN SUPPORT ADDED WEIGHT OF BULB.

ATTENTION: L’UTILISATION EST AUTORISÉE UNIQUEMENT EN INTÉRIEUR.

NE PAS UTILISER COMME ÉCLAIRAGE D’URGENCE.

RISQUE DE CHOC ÉLECTRIQUE –UTILISER UNIQUEMENT DANS UN

ENDROIT SEC.

S’ASSURER QUE LE LUMINAIRE EST APTE À SUPPORTER LE

SUPPLÉMENT DE POIDS DE L’AMPOULE.

Inhaltsverzeichnis

Andere Sengled Arbeitsleuchte Handbücher

Sengled

Sengled Pulse Satellite Bedienungsanleitung

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

IKEA

IKEA STRÖMLINJE Bedienungsanleitung

Regent

Regent CHSL300 Bedienungsanleitung

Monzana

Monzana Spodaj MZUL277 Bedienungsanleitung