Sengoku OR-77 Leitfaden
1
Step 6
Unscrew the screw which holds the wind
cover and take off the wind cover.
Step 5
Unscrew 4 wing nuts.
Step 4
Carefully lift off the case.
Step 3
Unscrew 4 screws from the each side of
the case.
Step 2
Remove the wick adjusting knob by pull-
ing straight out. Remove the tank cap.
Step 1
Remove the batteries from the heater.
These Instructions are for the following models: OR-77 and OR-78.
Wick replacement should be performed on a completely cool heater after the tank is empty
and the remainder of the kerosene in the heater has been burned off.
Wick Replacement Instructions for Omni Radiant Kerosene Heaters
2
Wick Replacement Instructions for Omni Radiant Kerosene Heaters
Step 12
Insert the pinion on the inside of the wick
control shaft into top portion of the rack
of the wick holder.
Step 11
Replacement wick has a black line. Fold
the new wick and slide it into the holder
up to the line. The black line on the
outside of the wick should match the top
edge of the holder. Then carefully press
the wick against the teeth inside the
holder to obtain a rm grip.
Step 10
Remove the wick from the holder by
folding it inward. Loosen it from the sharp
metal teeth in the inner surface of the
holder and then slide it out.
Step 9
Remove the sleeve from the assembly.
Step 8
Pull out the wick holder assembly.
Step 7
Remove the automatic ignition assembly
by unscrewing 2 screws.
3
Wick Replacement Instructions for Omni Radiant Kerosene Heaters
Step 18
Check the function of safety shut off
mechanism by pushing down the manual
shut off lever or upsetting the pendulum.
Step 17
Check height of wick (10+-1mm). Check for
correct clearance between wick holder and
draft tube (all around). This can be done eas-
ily using 5/32 or 3/16 dia. drill bit.
Step 15
Position the adjuster shaft to the front of the
heater. Use the knob to rotate the wick con-
trol shaft clockwise by ¾ turn. This rotates the
ratchet clockwise by ¾ turn. Turn the knob
clockwise and counter-clockwise a few times to
make sure that the wick travels up and down
smoothly. Hold the latch to prevent the safety
shut off device from being activated.
Step 16
Reinstall the automatic ignition assembly.
Snug, but do not tighten 4 wing nuts on
the mounting studs, then raise the wick to
the full “up” position, and evenly tighten
wing nuts in several steps.
Step 14
Ensure that the rubber gasket is in place
and slide the wick and holder back on the
draft tube. Rotate them 90 degrees left
and right and up and down until the wick
slides freely.
Step 13
Replace the wick adjusting knob on its
shaft and check to see that the spring
of the wick adjuster assembly is free of
torque (has no tension).
4
Wick Replacement Instructions for Omni Radiant Kerosene Heaters
Step 21
Ensure the proper chimney position. In-
stall the batteries in the battery case. Fill
the tank with clean, pure 1-K kerosene.
Wait at least 60 minutes for kerosene to
fully saturate the new wick.
Step 19
Replace the wind cover.
Step 20
Replace the cabinet, tighten 4 screws and
reinstall the wick adjusting knob.
Andere Handbücher für OR-77
2
Dieses Handbuch passt für folgende Modelle
1
Andere Sengoku Heizung Handbücher
Sengoku
Sengoku MGN-110 Bedienungsanleitung
Sengoku
Sengoku OR-77 Bedienungsanleitung
Sengoku
Sengoku MGN -110 Bedienungsanleitung
Sengoku
Sengoku Mega-23K Bedienungsanleitung
Sengoku
Sengoku OR-77 Bedienungsanleitung
Sengoku
Sengoku HeatMate HME-GS10 Bedienungsanleitung
Sengoku
Sengoku MGN-110 Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung