Sennetech SCT-1047 Bedienungsanleitung
SCT-1047 Ver. 1.0
1
CAMERACONTROLCODETRANSLATOR
PELCO RS-422 to JAVELIN RS-232 Ver. 1.0
SCT-1047
www.sennetech.net
Sennetech, Inc. 6455 W. Bath Rd. Perry, MI 48872 U.S.A. Ph (517) 675-1150 Fax (517) 675-1151
2
SCT-1047 Ver. 1.0
3
SPECIFICATIONS
SIZE: 5.57"W x 1.52H x 5.45D
WEIGHT: 1.5 lbs.
POWER: 9Volt to 15VoltAC or DC at 75ma
INDICATORS: Front panel LEDs: Power, Rx, & Tx
PELCORS-422 INPUT: (1)mating3-pin screw terminal connector
JAVELINRS-232OUTPUTS: (4)mating3-pin screw terminal connectors
PRODUCTDESCRIPTION
The SCT-1047 is a Pelco to Javelin control code translator designed to permit control of Javelin
camerasfromPelco controllers. ItreceivesPelco RS-422 commandsandtransmits the appropri-
ate commands in Javelin RS-232 format (9600 baud N81). There are four independent Javelin
outputs.
The unit's operating mode is set with an internal configuration switch. It can be configured to
accepteitherPelco "P"or"D" code. Theoutputcan be Javelincodecompatible with eitherJO208
ACUsorJO308ACUs.
Inputandoutput connectionsaremade with matingscrewterminal connectors. FrontpanelLEDs
indicatestatusof power,receive,andtransmit.
There is an optional 19" rack mount panel (one rack unit high).
4
To settheconfiguration switches, remove the
back panel, which is secured by two screws.
Then slide the cover back to expose the
switches.
Theswitchescanbechangedwhilethe code
translatorispowered up andthenew settings
will take effect immediately.
SW1-8
PELCOCODETYPE
ON: "P"CODE
OFF:"D"CODE
Settomatchthe typeof codefrom
thePelcocontrolsystem
WhensettingupPelco com portsto
workwithacodetranslator,configure
theportthe sameasitwouldbe fora
Pelcodome.
SW1-7
"P"CODE BAUDRATE
ON: 9600 BAUD
OFF:4800BAUD
Thisswitchisignored if SW1-7isOFF.
SW1-5
JAVELINCODETYPE
ON: JO208
OFF:JO308
SETTINGTHE SWITCHES
CONFIGURATION
SWITCH
U11 U10 U9 U8
U13
U6
U3
U4
CN7 CN6 CN5 CN4 CN2
CN1
U2
U1
SW1
SENNETECH
55-9702
12345678
ON
OFF
SCT-1047 Ver. 1.0
5
Pelco
RS-422
input
Power
input
JavelinRS-232 outputs
Connect output Tx & Com
to Javelin Rx & Com pins.
Ifconnectingtoa J0310 SDU
SCT-1047 SDU
Tx------------------pin2
Com---------------pin5
Ifconnectingto aJavelinRemote
Receiverfor controlof JO208
ACUsviaa JO107multiplexer
SCT-1047 RCVR
Tx------------------pin2
Com---------------pin7
Power
indicator Pelco
receive
indicator
Javelin
transmit
indicator
FRONTPANEL
REARPANEL
INSTALLATION
Power TxRx
CODETRANSLATOR
PELCO
RS-422 IN POWER
9V to 15V
AC or DC
JAVELIN RS-232 OUTPUTS
S Rx Tx Com Rx Tx Com Rx Tx Com Rx Tx Com
6
SCT-1047 Ver. 1.0
7
OPERATION
Pan, Tilt, Zoom, Focus, and Iris commands are converted directly. Additional functions use the
followingtable.
PELCO COMMAND JAVELIN COMMAND
Prog Pset 1 to 16 StorePre-position(1 to 16)
Goto Pset 1 to 16 RecallPre-position(1to 16)
Pelco Program Preset [61] to [68] commands set the Javelin camera movement limits.
61 Set Set Right Limit
62 Set Clear RightLimit
63 Set Set Down Limit
64 Set ClearDownLimit
65 Set Set Left Limit
66 Set Clear LeftLimit
67 Set Set Up Limit
68 Set Clear UpLimit
There are six Javelin "F" or "R" commands that can be used to control relays. PelcoAux
commandsareconverted to these commands.
1On R1
2On R2
3On R3
4On R4
5 On R5 orAuto Scan
6 On R6 or RandomScan
8
January 2006 SCT-1047 Ver. 1.0
Inhaltsverzeichnis
Andere Sennetech Elektronisches Wörterbuch Handbücher
Sennetech
Sennetech SCT-CTX Bedienungsanleitung
Sennetech
Sennetech SCT-1034 Bedienungsanleitung
Sennetech
Sennetech SCT-1027 Bedienungsanleitung
Sennetech
Sennetech SCT-CRX-Pelco-Pelco Bedienungsanleitung
Sennetech
Sennetech SCT-CRX-Pelco-Vicon Bedienungsanleitung
Sennetech
Sennetech SCT-1066 Bedienungsanleitung
Sennetech
Sennetech SCT-1058 Bedienungsanleitung
Sennetech
Sennetech SCT-1060 Bedienungsanleitung
Sennetech
Sennetech SCT-1041 Bedienungsanleitung
Sennetech
Sennetech SCT-CTX-Pelco-Panasonic v20 Gebrauchsanweisung
